SL358 SLS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Low Power Dual Operational Amplifier The SL358 contains two independent high gain operational amplifiers with internal frequency compensation. The t wo op -amps operate over a wide voltage range from a single power supply. Also use a split power supply. The device has low power supply current drain, regardless of the power supply voltage. The low power drain also makes the SL358 a good choice for batter y operation. When your project calls for a traditional op -amp function, now you can streamline your design with a simple single power supply. Use ordinary +5VDC common to practically any digital system or personal computer application, without requiring an extra 15V power supply just to have the interface electronics you need. The SL358 is a versatile, rugged workhorse with a thousand -and- one uses, from amplifying signals from a variety of transducers to dc gain blocks, or any op -amp function. The attached pages offer some recipes that will have your project cooking in no time.

  • Internally frequency compensated for unity gain
  • Large DC voltage gain: 100dB
  • Wide power supply range:
  • Input common-mode voltage range includes ground
  • Large output voltage swing: 0V DC to VCC-1.5V DC
  • Power drain suitable for battery operation
  • Low input offset voltage and offset current
  • Differential input voltage range equal to the power supply voltage

ORDERING INFORMATION

TA = 0° to 70° C for all packages. LOGIC DIAGRAM PIN 4 = GND PIN 8=VCC PIN ASSIGNMENT

MAXIMUM RATINGS* Symbol Parameter Value Unit VCC Power Supply Voltages Single Supply Split Supplies ±16 V VIDR Input Differential Voltage Range (1) ±32 V VICR Input Common Mode Voltage Range -0.3 to 32 V ISC Output Short Circuit Duration Continuous TJ Junction Temperature Plastic Packages 150 Tstg Storage Temperature Plastic Packages -55 to +125 IIN Input Current, per pin (2) 50 mA TL Lead Temperature, 1mm from Case for 10 Seconds 260 °C *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C Notes: 1. Split Power Supplies. 2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit VCC DC Supply Voltage ±2.5 or 5.0 ±15 or V TA Operating Temperature, All Package Types 0 +70 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high -impedance circuit. For proper operation, V IN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC). Unused outputs must be left open.

DC ELECTRICAL CHARACTERISTICS(TA=0 to +70°C) Guaranteed Limit Symbol Parameter Test Conditions Min Typ Max Unit VIO Maximum Input Offset Voltage VO=1.4V VCC=5.0-30V;RS=0Ω VICM=0V to VCC-1.7V 9.0 mV ΔVIO/ΔT Input Offset Voltage Drift RS=0Ω , VCC=30V 7.0 µV/°C IIO Maximum Input Offset Current VCC=5.0V 150 nA ΔIIO/ΔT Input Offset Current Drift RS=0Ω , VCC=30V 10 pA/°C IIB Maximum Input Bias Current VCC=5.0V -500 nA VICR Input Common Mode Voltage Range VCC=30V 0 28 V ICC Maximum Power Supply Current RL=∞,VCC=30V,V0=0V RL=∞,VCC=5V,V0=0V 1.2 mA AVOL Minimum Large Signal Open-Loop Voltage Gain VCC=15V, RL≥2KΩ 15 V/mV VOH Minimum Output High- Level Voltage Swing VCC=30V,RL=2KΩ VCC=30V,RL=10KΩ V VOL Maximum Output Low- Level Voltage Swing VCC=5V,RL=10KΩ 20 mV CMR Common Mode Rejection VCC=30V, RS=10KΩ 65* dB PSR Power Supply Rejection VCC=30V 65 dB CS Channel Separation f=1KHz to 20KHz,VCC=30V -120* dB ISC Maximum Output Short Circuit to GND VCC=5.0V 60* mA Isource Minimum Source Output Current VIN+ =1V, VIN-=0V, VCC=15V, V0=0V 10 mA Isink Minimum Output Sink Current VIN+ =0V, VIN-=1V, VCC=15V, V0=15V VIN+ =0V, VIN-=1V, VCC=15V, V0=0.2V 12* mA µA VIDR Differential Input Voltage Range All VIN≥GND or V-Supply (if used) VCC* V *=@25°C