SL34063A SLS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

DC-TO-DC CONVERTER CONTROL CIRCUITS The SL34063A is a monolithic control circuit containing the primary functions required for DC -to-DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically designed to be incorporated in Step-Down and Step-Up and Voltage-Inverting applications with a minimum number of external components.

FEATURES

  • Operation from 3.0 V to 40 V Input
  • Low Standby Current
  • Current Limiting
  • Output Switch Current to 1.5 A
  • Output Voltage Adjustable
  • Frequency Operation to 100 kHz
  • Precision 2% Reference MAXIMUM RATINGS Rating Symbol Value Unit Power Supply Voltage VCC 40 Vdc Comparator Input Voltage Range VIR -0.3 to +40 Vdc Switch Collector Voltage VC(switch) 40 Vdc Switch Emitter Voltage (Vpin 1 = 40 V) VE(switch) 40 Vdc Switch Collector to Emitter Voltage VCE(switch) 40 Vdc Driver Collector Voltage IC(driver) 40 Vdc Driver Collector Current (Note 1) IC(driver) 100 mA Switch Current ISW 1.5 A Power Dissipation and Thermal Characteristics Ceramic Package, U Suffix TA = +25°C Thermal Resistance Plastic Package, P Suffix TA = +25°C Thermal Resistance Thermal Resistance PD RθJA PD RθJA PD RθJA 1.25 100 1.25 100 625 160 W °C/W W °C/W mW °C/ W Operating Junction Temperature TJ +150 °C Operating Ambient Temperature Range TA 0 to +70 °C Storage Temperature Range Tstg -65to+150 °C SL34063A

ORDERING INFORMATION

34063AD 0° to +70°C SO-8 34063AP1 Plastic DIP ELECTRICAL CHARACTERICISTICS (VCC = 5.0 V, TA= 0 to +70oC unless otherwise specified.) Characteristics Symbol Min Typ Max Unit OSCILLATOR Frequency (VPin 5 = 0 V, CT = 1.0 nF, TA = 25°C) fosc 24 33 42 kHz Charge Current (VCC = 5.0 V to 40 V, T A = 25°C) Ichg 24 33 42 µA Discharge Current (VCC = 5.0 V to 40 V, TA = 25°C) Idischg 140 200 260 µA Discharge to Charge Current Ratio (Pin7 to Vcc, TA=25°C) Idischg/Ichg 5.2 6.2 7.5 — Current Limit Sense Voltage (Ichg = Idischg, TA = 25°C) Vlpk(sense) 250 300 350 mV OUTPUT SWITCH (Note 3) Saturation Voltage, Darlington C onnection (ISW = 1.0 A, Pins 1, 8 connected) VCE(sat) — 1.0 1.3 V Saturation Voltage (ISW = 1.0 A, R Pin 8 = 82 Ω to VCC. Forced β = 20) VCE(sat) — 0.45 0.7 V DC Current Gain (ISW = 1.0 A, V CE = 5.0 V, TA = 25°C) hFE 50 120 — — Collector Off-State Current (VCE = 40V) IC(off) — 0.01 100 µA COMPARATOR Threshold Voltage (TA = 25°C) (TA = TLOW to THIGH) Vth 1.225 1.21 1.25 1.275 1.29 V Threshold Voltage (TA = 25°C) ** Vth 1.2375 1.25 1.2625 V Threshold Voltage Line Regulation (VCC = 3 0 V to 40 V) Regime 1.4 5.0 mV Input Bias Current (Vin=0V) IIB — -40 -400 nA TOTAL DEVICE Supply Current (VCC = 5 0 V to 40 V, CT = 1 0 nF, Vpin7 = VCC. VPin5 > Vth, Pin 2 = Gnd, Remaining pins open) ICC 2.5 4.0 mA NOTES: 1. Maximum package power dissipation li mits must be observed. 2.Low duty cycle pulse techniques are used during test to maintain Junction temperature as close to ambient temperature as possible 3.If the output switch is driven into hard saturation (non Darlington configuration) at low switch c urrents (< 300 mA) and high driver currents (>30 mA), it may take up to 2.0 µs to come out of saturation This condition will shorten the off' time at frequencies > 30 kHz, and is magnified at high temperatures This condition does not occur with a Darlingto n configuration, since the output switch cannot saturate If a non Darlington configuration is used, the following output drive condition is recommended Forced β of output switch = IC, output/(Ic, driver -7.0 mA*) > 10 *The 100 Ω . resistor in the emitter o f the driver device requires about 7.0 mA before the output switch conducts **Possible version for shipment Pin connection