DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
検 出 TACT Switch TM Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Soldering of the frame realizes higher solder strength Side Push Type with 1.55mm Height (Surface Mount Type)SKTD Circuit Arrangement ■ Typical Specifications Items Specifications Rating （max.） 50mA 12V DC Rating （min.） 10μA 1V DC Initial contact resistance 500mΩ max. Travel （mm） 0.15 Protective structure ※ IP67 equivalent 4,500 Japan Export Operating force Operating life （5mA 5V DC）Product No. ■ Product Line Operating direction Side push1.6NSKTDLDE010 200,000 cycles Dimensions Unit:mm PC board mounting hole and land dimensions （Viewed from switch mounting face）Style Packing Specifications Taping Reel size Unit:mm 4,500 Minimum order unit （pcs.） ø380 13.5 1.5 0.9 Guide bosses 3.9 2.9 0.95 1.5 1.550.45 Stem 3.7 2.31.15 1.15 0.95 0.95 1.1 0.8 1.1 1.4 2.10.7 0.7 2- Ø0.55 2- R 0.4 Through-hole 1 2 ① ② Number of packages （pcs.） Tape width （mm） Export package measurements （mm）1 reel 1 case / Japan 1 case / export packing 4,500 45,000 45,000 12 4 01× 4 01×214 For reels of 330mm diameter, please inquire. Note ※ Assumes the switch is left alone without being operated. Under the specified conditions, dust and water ingress with a significant impact on the switch's on-off function is prevented. IP67 dust and water resistance is guaranteed for the switch alone and performance may not be guaranteed depending on the mounting conditions and usage. 1.5 0.9 Guide bosses 3.9 2.9 0.95 1.5 1.550.45 Stem 3.7 2.31.15 1.15 0.950.95 1.1 0.8 1.1 1.4 2.10.7 0.7 2- Ø0.55 2- R 0.4 Through-hole 1 2 Refer to P.259 for soldering conditions.
検 出 TACT Switch TM Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Type Sharp Feeling Type Surface Mount Series SKHU SKTD SKSN SKTG SKSL SKSC SKRT SKRV SKRH Photo Features — Low–profile Mid-mount Half-mount Low–profile — 4–direction switch ＋push switch IP standard — 67 equivalency — 67 equivalency — — — — — Operating direction Dimensions （mm） Operation force coverage to 1N See the relevant pages for respective product description 1N to 2N 2N to 3N 3N to 4N 4N to 5N respective product description Life Cycle Electrical performance Rating （max.） （Resistive load） 5 0m A 12V D C Rating （min.） （Resistive load） 10μA 1V DC Insulation resistance 100MΩ m in. 10 0V D C 1min. Durability Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively Lifetime Shall be in accordance with individual specifications. Environmental performance Cold −40℃ 96h −30℃ 96h −40℃ 96h Dry heat 90℃ 96h 85℃ 96h 90℃ 96h 85℃ 96h 90℃ 96h 80℃ 96h 90℃ 96h Damp heat 60℃, 90 to 95%RH 96h Page 237 239 240 241 242 243 245 453 454 TACT Switch TM T ACT Switch TM Notes 1. The automotive operating temperature range to be individually discussed upon request. 2. ● Indicates applicability to all products in the series, while ○ indicates applicability to some products in the series. W：Width. The most outer dimension excluding terminal portion. D ：Depth. The most outer dimension excluding terminal portion. H ：Height. The minimum dimension if there are variances. NEW
検 出 TACT Switch TM Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type TACT Switch TM Soldering Conditions 1. Temperature measurement: Thermocouple φ 0.1 to 0.2 CA （K） or CC （T） at solder joints （copper foil surface） . A heat resistive tape should be used to fix thermocouple. 2. Temperature profile Condition for Reflow Available for Surface Mount Type. 180 150 260˚C max. 3 sec max. 230˚C Time 120 sec max. ʢpre-heating ʣ 3 to 4min. Time inside soldering equipment Temperature (˚C ) 40s max. 1. Prevent flux penetration from the top side of the TACT Switch TM 2. Switch terminals and a PC board should not be coated with flux prior to soldering. 3. The second soldering should be done after the switch is stable with normal temperature. 4. Use the flux with a specific gravity of min 0.81. （EC-19S-8 by TAMURA Corporation, or equivalents.） Notes 1. The above temperature shall be measured of the top of switch. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Notes Conditions for Auto-dip Available for Snap-in Type and Radial Type. Items Condition Flux built-up Mounting surface should not be exposed to flux Preheating temperature Ambient temperature of the soldered surface of PC board. 100℃ max. Preheating time 60s max. Soldering temperature 260℃ max. Duration of immersion 5s max. Number of soldering 2times max. SKHH, SKPD Series Items Condition Flux built-up Mounting surface should not be exposed to flux Preheating temperature Ambient temperature of the soldered surface of PC board. 1 10℃ max. Preheating time 60s max. Soldering temperature 260℃ max. Duration of immersion 5s max. Number of soldering 2times max. SKQJ, SKQK, SKEG Series Items Condition Flux built-up Mounting surface should not be exposed to flux Preheating temperature Ambient temperature of the soldered surface of PC board. 100℃ max. Preheating time 45s max. Soldering temperature 255℃ max. Duration of immersion 5s max. Number of soldering 2times max. Manual Soldering Items Condition Soldering temperature 350℃ max. Duration of soldering 3s max. Capacity of soldering iron 60W max. SKHH, SKHW, SKRG, SKPD Series Items Condition Soldering temperature 360℃ max. Duration of soldering 3s max. Capacity of soldering iron 60W max. SKTD, SKTG, SKQJ, SKQK, SKEG Series Items Condition Soldering temperature 350℃ max. Duration of soldering 3s max. Capacity of soldering iron 20W max.