SFU-43-48H-HP-CDE

SFU-43-48H-HP-CDE SOURCE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

• Burst receive PON OLT transceiver
• “Fast Signal Detect” feature reduces ranging overhead
• Simplifed OLT “reset” timing
• Small Form Factor, 2 x 10 pigtailed bi-directiona l
• 1490 nm DFB Tx with isolator
• 1310 nm APD Rx
• 2488 Mbps downstream Tx/1244 Mbps upstream Rx
• Single 3.3 V supply
• ITU-T G.984.2 compliant
• 20 km reach; 28 dB link budget
• SC/UPC fiber connector; IEC 61754-4 compliant
• RoHS-5/6 compliant (lead exemption) Parameter Symbol Min. Typ. Max. Unit Supply Voltage Vcc_MAX 0 - 3.6 V Operation Relative Humidity RHs 5 - 90 % Storage Temperature Tstg -40 - 85 ºC Maximum Receiver Input Power PIn_max + 3 - - dBm TX Disable Logic High State TX_DIS_max 0 - Vcc+0.5 V RX Reset Logic High State Reset_max 0 - Vcc+0.5 V I2C Serial Data Logic High State SDAmax - - Vcc+0.5 V I2C Serial Clock Logic High State SCLmax - - Vcc+0.5 V Absolute Maximum Rating Parameter Symbol Min. Typ. Max. Unit Back Reflection at 1490 nm - - -20 dB Back Reflection at 1310 nm - - -20 dB 1490 nm to 1310 nm crosstalk - - -45 dB General Optical Parameters Parameter Symbol Min. Typ. Max. Unit Operating Voltage Vcc 3.135 3.3 3.465 V Total Supply Current ICC - - 450 mA Case Operating Temerature (-CDE) Topr -5 - 70 ºC Case Operating Temerature (-RDE) Topr -20 - 85 ºC Case Operating Temerature (-TDE) Topr -40 - 85 ºC Storage Temperature Tstg -40 - 85 ºC General Operating

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM Parameter Symbol Min Typical Max Unit Input Differential Impedence Rin 80 100 120 Ω Single Ended data input swing (ac coupled inside module) Vin, p-p 300 - 1200 mV Tx Disable (LVTTL) Vd 2 - Vcc V Tx Enable (LVTTL) Ven 0 - 0.8 V Tx_Fail_High (LVTTL) V_Fail 2.4 - Vcc V Tx_Fail_Normal (LVTTL) V_Normal 0 - 0.4 V Transmitter Specifications (Electrical) Receiver Specifications (Optical) Parameter Symbol Min Typical Max Unit Wavelength λ 1260 1310 1360 nm Upstream Data Rate +/- 100ppm (burst-mode) - 1244 - Mbps Receiver Sensitivityc RENS - -31 -28 dBm Receiver Overloadc ROL -8 -5 - dBm Receiver Burst-mode Dynamic Ranged 15 20 - dB BRST_Det Assert (Signal Detected) P_DET - - -28 dBm Receiver CID Tolerance CID 72 - - bits Maximum Reflectance of Receiver RX_r - - -20 dB c) At 10-10 BER with PRBS 223-1 Burst-Mode data at 1244 Mb/s d) The input power difference between two subsequent high and low burst data. Parameter Symbol Min Typical Max Unit Optical Power Pop 1.5 - 5 dBm Average launch power of off Tx Poff - - -40 dBm Wavelength λ 1480 1490 1500 nm Spectral Width (-20 dB) ∆λ20 - - 1 nm Side Mode Suppression Ratio SMSR 30 - - dB Extinction Ratio ER 10 - - dB Transmit eye mask G.984.2 Downstream Bit Rate +/- 100ppm - 2488 - Mbps Transmitter CID immunity 72 - - bits Optical Rise timea - - 160 ps Optical Fall timea - - 160 ps Optical Path Penalty - - 0.5 dB Tolerence to TX back reflectionb -15 - dB Transmitter Specifications (Optical) a) 20% to 80% values b) 1 dB degradation of receiver sensitivity

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM Receiver Specifications (Electrical) e) 20% to 80% values f) BRST_Det assert low when module receive “reset” signal, assert high when incoming burst is detected and latch to high state until next “Reset” signal. g) Timing for rising edge of “Reset” input singal is referenced to module pins with assumption of 4 bytes guard time after previous burst end h) RX output will start to chatter after T_chatter if there is no optical input or reset signal present. Parameter Symbol Min Typical Max Unit PECL Single ended data output swing(LVPECL) Vout,p-p 250 - 800 mV Data output rise timee tr - 250 - ps Data output fall timee tf - 250 - ps BRST_Det_Highf V_DETH 2.4 - Vcc V BRST_Det_Lowf V_DETL 0 - 0.4 V BRST_Det Response Time T_BRST_Det - - 6.4 nS Reset Input Timingg T_Reset_start -0.5 0 +1 Byte Reset Input Duration T_Reset 2 - - Byte RX output chatter time constanth T_chatter 300 - - nS Parameter Symbol Min Typical Max Unit I2C Serial Data High VSDA_H 2.0 - Vcc V I2C Serial Data Low VSDA_L 0 - 0.8 V I2C Serial Clock High VSCL_H 2.0 - Vcc V I2C Serial Clock Low VSCL_L 0 - 0.8 V TX Power DDM Error TXDDM - - +/- 3 dBm Case Temperature DDM Error TDDM - - +/- 5 ºC TX Bias DDM Error TXBIASDDM - - +/- 10 mA Vcc DDM Error VCCDDM - - +/- 0.3 V I2C Serial Logic & Digital Diagnostic Monitor (DDM)

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM EEPROM Pin Function Notes 1 Reset CMOS input. Assert “Reset” high at the end of previous burst, 2 bytes in duration

2 Pmon_analog Analog signal output for receiver optical input power monitoring

3 RX_GND Rx Ground

4 Reserved No User Connection; Internal use

5 Reserved No User Connection; Internal use

6 RX_GND Rx Ground

7 RX_Vcc Rx Vcc

8 BRST_Det LVTTL output. BRST_Det assert low when module receives “reset” signal, assert high when incoming burst is present.

9 RXD- Negative Data Output, LVPECL; DC coupled

10 RXD+ Positive Data Output, LVPECL; DC coupled

11 TX_Vcc Tx Vcc

12 TX_GND Tx Ground

13 TX_DIS Tx Disable. LVTTL input. Laser output is disabled when this pin is asserted high or left unconnected. Laser output is enabled when this pin is asserted low.

14 TXD+ Positive Data Input, LVPECL or CML (AC coupled; internally 100 ohms differential termi-

nation)

15 TXD- Negative Data Input, LVPECLor CML (AC coupled; internally 100 ohms differential termi-

nation)

16 TX_GND Tx Ground

17 SCL 2-Wire Serial Clock Input. Clocks data into and out of the device. 18 SDA 2-Wire Serial Data I/O Pin. Transfers serial data to and from the device. 19 TX_FAIL Tx Fail Alarm. LVTTL Output Active high.

20 TX_GND Tx Ground

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM Timing Diagram Detailed burst-mode receiver timing diagram is available upon request.

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM EEPROM Content DEC Addr. HEX Addr. Field Size (bytes) Name Default Value Description 0 00 1 Identifier 02h Module soldered to motherboard 1 01 1 Extended Identifier 04h Function defined by serial ID 2 02 1 Connector 0Bh (pigtail). Optical pigtail 3 03 8 Transceiver 00 00 00 00 00 00 00 00h Transceiver Code Field, not applicable 11 0B 1 Encoding 03h NRZ encoding 12 0C 1 Nominal Bit Rate in 100 MBps 19h 2488.32 Mbps 13 0D 1 Reserved 00h Reserved 14 0E 1 Length (9µ, km) in km 14h 20km 15 0F 1 Length (9µ, m) in 100 m C8h 20km 16 10 1 Length (50µ) in 10 m 00h Not Supported 17 11 1 Length (62.5µ) in 10 m 00h Not Supported 18 12 1 Length (Copper) in m 00h Not Supported 19 13 1 Reserved 00h Reserved 20 14 16 Vendor Name (ASCII) "LUMINENTOIC " Vendor Name (ASCII) 36 24 1 Reserved 00h Reserved 37 25 3 Vender IEEE Company ID 00 06 B5h LuminentOIC IEEE ID 40 28 16 Vendor Part Number (ASCII) "SFU4348HHPxDExxx" Vendor Part Number (ASCII) 56 38 4 Vendor Rev (ASCII) 31 20 20 20 Revision 60 3C 2 Laser Wavelength in nm 05 D2h 1490nm Tx Wavelength 62 3E 1 Reserved 00h Reserved 63 3F 1 Check Code for Base ID Fields xxh Checksum from byte 0-62 64 40 2 Options 00 1Ch TX_DIS, TX_Fault, SD 66 42 1 Upper Bit Rate Margin in % 00h BR, Max not specified 67 43 1 Lower Bit Rate Margin in % 00h BR, Min not specified 68 44 16 Vendor Serial Number (ASCII) "xxxxxxxxxxxxxxxx" 16 byte Serial number field (ASCII) 84 54 8 Date Code xx xx xx xx xx xx 20 20h Year(2 bytes) month(2 bytes) day(2 bytes) 92 5C 1 Diagnostic Monitoring Type 58h Ext Calibration, Average Power Measurement 93 5D 1 Enhanced Options E0h Optical Alarm/warning implemented Soft TX_DIS, TX_FAULT implemented 94 5E 1 SFF-8472 Compliance 02h Compliance to SFF-8472 Rev 9.4 95 5F 1 Check Code for Extended ID Fields xxh Checksum from byte 64-69 96 60 30 Vendor Specific "SFU-43-48H-HP-xDE-xx " LOIC part number (ASCII) 126 7E 2 Vendor Specific 0C 83h Upstream Bit Rate (100 Mbps units) and Receive Wavelength (10 nm units) 128 80 128 Reserved 00….00h Reserved; return to 0 I2C A0h Address For detailed specifications of EEPROM contents and externally calibrated digital diagnostic monitor (DDM) functions, please refer to SFF-8472 standard Rev 9.5.

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM DEC Addr. HEX Addr. Field Size (bytes) Name Default Value Description 0 00 2 Temp High Alarm xx xxh 80C (-CDE); 92C(-RDE); 92C(-TDE) 2 02 2 Temp Low Alarm xx xxh -13C(-CDE);-28(-RDE);-48C(-TDE) 4 04 2 Temp High Warning xx xxh 75C(-CDE); 87C(-RDE); 87C(-TDE) 6 06 2 Temp Low Warning xx xxh -8C(-CDE); -23C(-RDE); -43C(-TDE) 8 08 2 Voltage High Alarm 94 70h 3.8V 10 0A 2 Voltage Low Alarm 6D 60h 2.8V 12 0C 2 Voltage High Warning 8C A0h 3.6V 14 0E 2 Voltage Low Warning 75 30h 3.0V 16 10 2 Bias High Alarm 83 81h 110mA 18 12 2 Bias Low Alarm 02 64h 2mA 20 14 2 Bias High Warning 77 8Ch 100mA 22 16 2 Bias Low Warning 03 96h 3mA 24 18 2 TX Power High Alarm xx xxh +5.5 dBm 26 1A 2 TX Power Low Alarm xx xxh +0.5dBm 28 1C 2 TX Power High Warning xx xxh +5.0dBm 30 1E 2 TX Power Low Warning xx xxh +1.0dBm 32 20 2 RX Power High Alarm FF FFh No alarm 34 22 2 RX Power Low Alarm 00 00h No alarm 36 24 2 RX Power High Warning FF FFh No alarm 38 26 2 RX Power Low Warning 00 00h No alarm 40 28 16 Reserved 00….000h Reserved 56 38 4 RX_PWR(4) Calibration xx xx xx xxh 4th order RSSI calibration coefficient 60 3C 4 RX_PWR(3) Calibration xx xx xx xxh 3rd order RSSI calibration coefficient 64 40 4 RX_PWR(2) Calibration xx xx xx xxh 2nd order RSSI calibration coefficient 68 44 4 RX_PWR(1) Calibration xx xx xx xxh 1st order RSSI calibration coefficient 72 48 4 RX_PWR(0) Calibration xx xx xx xxh 0th order RSSI calibration coefficient 76 4C 2 TX_I(Slope) Calibration 01 A3h Slope for Bias calibration 78 4E 2 TX_I(Offset) Calibration 00 00h Offset for Bias calibration 80 50 2 TX_PWR(Slope) Calibration xx xxh Slope for TX Power calibration 82 52 2 TX_PWR(Offset) Calibration xx xxh Offset for TX Power calibration 84 54 2 T(Slope) Calibration 01 00h Slope for Temperature calibration 86 56 2 T(Offset) Calibration xx xxh Offset for Temperature calibration, in units of 256ths C 88 58 2 V(Slope) Calibration 01 00h Slope for VCC calibration 90 5A 2 V(Offset) Calibration 00 00h Offset for VCC calibration 92 5C 3 Reserved 00h reserved 95 5F 1 Checksum xxh Checksum 96 60 2 Transceiver Temperature xx xxh Temperature in C/256 98 62 2 Supply Voltage xx xxh Vcc 100 64 2 TX Bias Current xx xxh BIASMON 102 66 2 TX Optical Output Power xx xxh Back facet monitor 104 68 2 RX Optical Input Power xx xxh RSSI 106 6A 2 Reserved 0000h Reserved 108 6C 2 Reserved 0000h Reserved 6E.7 1bit TX_DIS State x Digital state of the TX Disable Input Pin. 6E.6 1bit Soft TX Disable x Read/write bit that allows software disable of laser. 6E.5 1bit Reserved. 0 Reserved. 6E.4 1bit Rate Select State 0 NOT SUPPORTED. 6E.3 1bit Rate Select 0 NOT SUPPORTED. 6E.2 1bit TX_FAULT x Digital state of the TX Fault Output Pin. 6E.1 1bit LOS 0 Digital state of the LOS Output Pin. NOT SUPPORTED 6E.0 1bit Data_ready_bar x Indicates transceiver has achieved power up and data is ready. I2C A2h Address 110

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM DEC Addr. HEX Addr. Field Size (bytes) Name Default Value Description 6F.7 1bit Reserved 0 Reserved 6F.6 1bit Reserved 0 Reserved 6F.5 1bit Reserved 0 Reserved 6F.4 1bit Reserved 0 Reserved 6F.3 1bit Reserved 0 Reserved 6F.2 1bit INTERRUPT_NOT x Interrupt state (active low) 6F.1 1bit MODE_EN 0 TX FAULT pin enable 6F.0 1bit APD_SHUTDOWN x APD shut-down latch. Write 0 to clear condition 70.7 1bit Temperature too high alarm x Temperature too high alarm 70.6 1bit Temperature too low alarm x Temperature too low alarm 70.5 1bit VCC too high alarm x VCC too high alarm 70.4 1bit VCC too low alarm x VCC too low alarm 70.3 1bit BIASMON too high alarm x BIASMON too high alarm 70.2 1bit BIASMON too low alarm x BIASMON too low alarm 70.1 1bit BFMON too high alarm x BFMON too high alarm 70.0 1bit BFMON too low alarm x BFMON too low alarm 71.7 1bit RSSI too high alarm x RSSI too high alarm 71.6 1bit RSSI too low alarm x RSSI too low alarm 71.5 1bit Reserved interrupt status bit x Reserved interrupt status bit 71.4 1bit Reserved interrupt status bit x Reserved interrupt status bit 71.3 1bit Reserved interrupt status bit x Reserved interrupt status bit 71.2 1bit Reserved interrupt status bit x Reserved interrupt status bit 71.1 1bit Reserved interrupt status bit x TX Fail went HIGH 71.0 1bit Reserved interrupt status bit x APD Shutdown event detected 114 72 1 Reserved 00h Interrupt Mask for ISRC0 115 73 1 Reserved 00h Interrupt Mask for ISRC1 74.7 1bit Temperature too high warning x Temperature too high warning 74.6 1bit Temperature too low warning x Temperature too low warning 74.5 1bit VCC too high warning x VCC too high warning 74.4 1bit VCC too low warning x VCC too low warning 74.3 1bit BIASMON too high warning x BIASMON too high warning 74.2 1bit BIASMON too low warning x BIASMON too low warning 74.1 1bit BFMON too high warning x BFMON too high warning 74.0 1bit BFMON too low warning x BFMON too low warning 75.7 1bit RX Power High Warning x RSSI too high warning 75.6 1bit RX Power Low Warning x RSSI too low warning 75.5 1bit Reserved 0 Reserved 75.4 1bit Reserved 0 Reserved 75.3 1bit Reserved 0 Reserved 75.2 1bit Reserved 0 Reserved 75.1 1bit Reserved 0 Reserved 75.0 1bit Reserved 0 Reserved 118 76 1 Reserved 00h Interrupt Mask for ISRC2 119 77 1 Reserved 00h Interrupt Mask for ISRC3 120 78 8 Vendor Specific 00 00 00 00 00 00 00 00h Vendor Specific I2C A2h Address 116 117 111 112 113

1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Rev A.0 SHOR T FORM LUMINENTOIC.COM Outline Drawing SBAT094. 54.21 739.3073.93 ]0010001[ 691. 89.4 085.1 31.04 005. 07.21 055. 79.31 432. 49.5 90.05 279.1 87.1 070. 036. 61.01 004. 500.010. 291.1 82.03 52.0+ 005. 000.- 010.+ 07.21 0 053. 98.8

01 NIP

02 NIP

1 NIP

11 NIP

1. 72.1 A LIATED 1 : 8 ELACS 010. 52.0 041. 65.3 SECALP 4 810. 15.0 64.0 020. 040.X2 20.1 PYT021. 40.3

IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran ties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu- ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2005 All rights reserved Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. SFU-43-48H-HP-xDE 1490nm/1310nm Single Fiber SFFB Transceiver Rev A.0 SHOR T FORM LUMINENTOIC.COM

Ordering information

n Order Option: SFU-43-48H-HP-CDE SFU-43-48H-HP-RDE SFU-43-48H-HP-TDE