SF1115A

SF1115A RFM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605

Electrical Characteristics

199.000 MHz Passband Insertion Loss at fc IL 7.0 dB 1 db Passband BW1 1, 2 ±100 kHz Amplitude Ripple over fc±100 kHz 0.5 dBP-P Group Delay Variation over fc ±100 kHz GDV 500 nsP-P Rejection Room Temperature fc+800 to fc+400 kHz 1, 2, 3 dB Room Temperature fc-800 to fc-400 kHz fc-800 to fc-600 and fc+600 to fc+800 kHz fc-30 MHz to fc-800 kHz fc+800 kHz to fc+17 MHz fc-80 MHz to fc-30 MHz fc+17 Mhz to fc+80 MHz Operating Temperature Range TA -35 +85 Frequency Temperature Coefficient FTC 0.032 ppm/°C2 SM9171-10 Designed for GSM BTS Receiver IF Applications Compatible with National Semiconductor Chip Set Very Flexible Impedance Matching Unbalanced or Balanced Input or Output 9.1 x 7.1 mm Version of the SF1115A-1 Complies with Directive 2002/95/EC (RoHS) Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +15 dBm Max. DC voltage between any 2 terminals VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max. Soldering Profile 260°C for 30 s

199 MHz

Impedance Matching to 50Ω Unbalanced External L-C Impedance Matching to 200Ω Balanced External L-C Impedance Matching to 50Ω Input / 400Ω Output External L-C Case Style SMP9171-10 9.1 x 7.1 mm Nominal Footprint Lid Symbolization (YY = year, WW = week) RFM SF1115A YYWW Pb Notes: Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center fre- quency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. The turnover temperature, TO, is the temperature of maximum (or turnover) frequency, fo. The nominal frequency at any case temperature, Tc, may be calculated from: f=fo[1-FTC(To-Tc)2]. The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, imped- ances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Electrostatic Sensitive Device. Observe precautions for handling.

199 MHz SAW Filter

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 3 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605 Case Dimensions Dimension mm Inches Min Nom Max Min Nom Max A 8.86 9.09 9.40 0.349 0.358 0.370 B 6.88 7.11 7.40 0.271 0.280 0.291 C 1.91 2.00 0.075 0.079 D 0.99 0.039 E 0.79 0.031 H 1.0 0.039 P 2.54 0.100 10-Terminal Ceramic Surface-Mount Case 9.1 x 7.1 mm Nominal Footprint SM9171-10 Case Electrical Connections Connection Terminals Port 1 Input or Return Return or Input Port 2 Output or Return Return or Output Ground All others Single Ended Operation Return is ground Differential Operation Return is hot Materials Solder Pad Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80- 200 µinches (203-508 µm) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 µinches Thick Body Al2O3 Ceramic Pb Free B A C H E (10 Places) P (10 Places) D

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 4 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 5 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605 Reference Designator Value Additional Information 4.7 pF 0805 Presido ± 0.25pF 4.7 pF 0805 Presido ± 0.25pF 270 nH

1008 Coilcraft Q=65 @ 350MHz 10%

0805 Presido ± 0.25pF 18 pF 0805 Presido ± 0.25pF xfmr1 1:4 ADT 4-1UT, 300-600MHz xfmr2 4:1 ADT 4-1UT, 300-600MHz SAW Matching Components

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 6 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 7 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605 COVER TAPE SIZE KO COVER TAPE 0.32 mm ±0.3 2.15 mm ±0.2 W (CARRIER TAPE SIZE) AO BO P (PITCH) 1.5 mm +0.1 -0.0 4.0 mm ±0.1 2.0 mm ±0.1 1.75 mm ±0.1 7.5 mm ±0.1 1.5 mm +0.3 -0.0 PIN #1 USER DIRECTION OF FEED COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.55 mm ±0.1 Bo 9.59 mm ±0.1 Ko 2.30 mm ±0.1 Pitch 12.0 mm ±0.1 W 16.0 mm ±0.3

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 8 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605 Leader and Trailer specifications (Based upon EIA-481)

7 Inch Reel Quantity 500

A N C D B Dimension 178 +0.5 -0.2 20.2 +1.5 ±0.5 16.4 22.4 MAX

13 Inch Reel Quantity 2000

A N C D B Dimension 330 100 +0.5 -0.2 20.2 +1.5 ±0.5 16.4 22.4 MAX Dimensions of the leader and trailer Dimensional drawing of the reel

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 9 of 12 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SF1115A-100605 Additional items (1) Cover tape peeling strength The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction. The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling direction of 165° to 180° (see the figure) and a peeling speed of 300mm/min. ±10mm/min. [EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm Tape material (1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 108 or less Material: Polystyrene or Polycarbonate (2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 1012 or less t = 50 to 100µm width = 13.3mm Warranty periods Cover tape peeling strength and mounting performance of stored components. 2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N) Number of missing components There shall not be two or more consecutive missing components. Also, the maximum number of missing components shall be the larger of one piece or 0.1%. Storage environment Keep the product on which taping has been performed to a temperature below 40°C and a humidity within 80% RH. Do not subject in the direct sun. Fixing method 1. Insert the tip of the carrier tape into the groove. 2. Fix the tip of the cover tape with adhesive tape.

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 10 of RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com Labeling The following items are labeled on the surface of a reel. Product Part Number, Date Code, Quantity

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 11 of RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com

7 Inch

13 Inch

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 12 of RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com RFM Qualification and Reliability Test Test Standard Test Parameters Pass / Fail Criteria Life at Elevated Temperature MIL-STD-202 Method 108 Condition C 1,000 Hours 125°C Unbiased Within Electrical & Hermetic Spec. (Note 1) Temperature Cycling JESD22 Method JA-104 Air-to-Air -55 ×Cto +125 ×C 20 min. Dwell 1,000 cycles Vibration, Variable Frequency MIL-STD-883 Method 2007 Condition B 50g Max.

4 Cycles, 3 Axis

20 Hz to 2 kHz to

1,500g Max.

5 Shocks

±3 Axis Destructive Bond Strength MIL-STD-883 Method 2011 Condition C Wire Bond Pull Strength 2.0 grams (After Seal) Die Shear Strength MIL-STD-883 Method 2019 Shear Strength 0.6 kg (Strength/area limit in development) Solderability (Note 2) J-STD-002 Method B 8 hr. steam age 245 × C solder temperature 5 second dwell >95% wetted surface Physical Dimensions JESD22 Method JB-100 Critical Dimensions Within specifications Temperature Characteristics RFM Procedure Frequency over Temperature Within specifications Terminal Strength (Note 2) MIL-STD-833 Method 2004 Condition A & D Cond. A-Lead Tension Cond. B -Pad Adhesionr 24 8 oz. - 30 sec. Visual Requirements & meets Hermetic Spec. Resistance to Solvents MIL-STD-883 Method 2015 Solvents a, b, d Visual Requirements Steady State Life MIL-STD-883 Method 1005 1,000 Hours Max. Operating Temperature Rated Voltage Within Electrical & Hermetic Spec. (Note 1) Internal Water- Vapor Content MIL-STD-883 Method 1018 < 5,001 PPM Constant Acceleration MIL-STD-883 Method 2001 Y1 Direction 30,000g Within Electrical & Hermetic Spec. (Note 1) Substrate Attach Strength MIL-STD-883 Method 2027 Tensile Strength of Die Attachment Custom per Device