SF1004G-Q1 TSC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
/cuspopen Low forward voltage drop /cuspopen High current capab ility /cuspopen High reliability /cuspopen High surge current capab ility Mechanical Data /cuspopen Case: Molded plastic /cuspopen Epoxy: UL 94V-O rate flame retardant /cuspopen Terminals: Leads solderable per MIL-STD- 202, Method 208 guaranteed /cuspopen Polarity: As marked /cuspopen High temperature soldering guaranteed: 2 6 0 oC/10 seconds .16”,(4.06mm) from c a s e . /cuspopen Weight: 2.24 grams TO-220 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 ℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol SF1004G-Q1 Units Maximum Recurrent Peak Reverse Voltage VRRM 200 V Maximum RMS Voltage VRMS 140 V Maximum DC Blocking Voltage VDC 200 V Maximum Average Forward Rec tified Current .375 (9.5mm) Lead Length @T C = 100 ℃ I(AV) 10.0 A Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) IFSM 125 A Maximum Instantaneous Forward Voltage @ 5 . 0 A @ 1 0 . 0 A VF 1.1 1.25 V Maximum DC Reverse Current @ T A=25℃ at Rated DC Blocking Voltage @ T A=100℃ IR 10.0 500 uA uA Reverse Recovery Charge(Per Diode) @IF=2A, VR ≧30V,-dIF/dt=20A/uS QS 9 NC Thermal Resistance Junction to Case (Note 3) RθJC 3.0 ℃/W Rating for Fusing (t < 8.3mS) I2t 65 A 2S Maximum Reverse Recovery Time (Note 1) Trr 25 nS Typical Junction Capacitance (Note 2) Cj 10 pF Operating Temperature Range TJ -50 to +150 ℃ Storage Temperature Range TSTG -50 to +150 ℃ Notes: 1. Reverse Recovery Test Conditions: I F=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Case Mounted on Heatsink. Size of 2 in x 3 in x 0.25 in, Al -Plate. PIN 1 PIN 3 Positive CT PIN 2 CASE
- 269 - RATINGS AND CHARACTERISTIC CURVES (SF1004G-Q1) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50/c87 NONINDUCTIVE /c49/c87 NON INDUCTIVE OSCILLOSCOPE (NOTE 1) PULSE GENERATOR (NOTE 2) DUT (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms (-) (+) 10/c87 NONINDUCTIVE -1.0A -0.25A +0.5A trr 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FOR WARD CURRENT . (A) 0 50 100 1500 CASE TEMPERATURE. ( C) o FIG.3- TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT .( A ) 0 20 40 60 80 100 120 140 1000 0.1 100 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) TJ=25 C0 TJ=100 C0 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FOR WARD SURGE CURRENT . (A) 1 2 5 10 20 100 50 150 120 NUMBER OF CYCLES AT 60Hz TJ=125 C0 8.3ms Single Half Sine Wave JEDEC Method FIG.5- TYPICAL JUNCTION CAPACITANCE CAPACITANCE.(pF) 15 2 10 20 50 100 200 500 100 REVERSE VOLTAGE. (V) Tj=25 C0 FIG.6- TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FOR WARD CURRENT . (A) 0.01 0.1 0.03 0.3 100 FORWARD VOLTAGE. (V) Tj=25 C Pulse Width=300 s 1% Duty Cycle o 1000