SE5012T SKYWORKS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

17 GND

Figure 2. SE5012T Pinout Table 1. SE5012T Signal Descriptions

1 EN PA enable 9 VDD LNA supply voltage

2 GND Ground 10 GND Ground

3 TXIN 5 GHz TX RF input signal 11 ANT 5 GHz antenna output

4 GND Ground 12 GND Ground

5 RX 5 GHz LNA output signal 13 DET Power detector output

6 GND Ground 14 H/L Lin High-low linearity control

7 C0 Switch control logic 1 15 VCC1 Power amplifier supply voltage

8 C1 Switch control logic 2 16 VCC2 Power stage supply voltage

Table 2. Recommended operating conditions are specified in Table 3. Electrical specifications are provided in Tables 4 through

  1. Figure 3 shows the power detector characteristics.

Table 2. SE5012T Absolute Maximum Ratings (Note 1) parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. Note 2: These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SE5012T Recommended Operating Conditions Table 4. SE5012T Electrical Specifications: Control Logic Characteristics (Note 1) Note 1: Performance is guaranteed only under the conditions listed in this table.

Table 5. SE5012T Electrical Specifications: Switch Logic Characteristics (Note 1) Note 1: Performance is guaranteed only under the conditions listed in this table. Table 6. Switch Control Logic Table Table 7. SE5012T Electrical Specifications: AC Characteristics (Transmit Characteristics) (Note 1)

64 QAM,

Note 1: Performance is guaranteed only under the conditions listed in this table.

Table 8. SE5012T Electrical Specifications: AC Characteristics (Receive Characteristics) (Note 1) Note 1: Performance is guaranteed only under the conditions listed in this table. Table 9. SE5012T Electrical Specifications: Power Detector Characteristics (Note 1) Note 1: Performance is guaranteed only under the conditions listed in this table. Figure 3. Power Detector Performance vs Frequency

Figure 4. Typical part markings are shown in Figure 5. Package moisture after the container seal is broken must be followed. Solder Reflow Information, document number 200164. done manually or in a production solder reflow environment.

  1. All dimensions are in millimeters.
  2. Dimensions and tolerances according to ASME Y14.5M-1994.
  3. Unless specified, dimensions are symmetrical about center lines.
  4. Via hole recommendations:

solder mask on the far side should tent or plug via holes. rounded corners offer better paste release.

  1. Solder mask recommendations:

Contact board fabricator for recommended solder mask offset and tolerance.

0.60 Typ

0.20 Typ

0.65 Typ

0.70 Typ

0.35 Typ

0.500 Typ

0.25 Typ

Figure 4. PCB Layout Footprint for the SE5012T

Figure 5. Typical Part Markings

0.15 C2X

0.30 X 45°

  1. All measurements are in millimeters.
  2. Dimensions and tolerances according to ASME Y14.5M-1994.
  3. Terminal #1 identification mark located within marked area.
  4. Unless specified, dimensions are symmetrical about center lines.

0.05 M C

0.10 M C A B

Figure 6. SE5012T Package Dimensions

  1. Measured from center line of sprocket hole to center line of pocket.
  2. Cumulative tolerance of 10 sprocket holes is ±0.20 mm.
  3. Other material available.
  4. Typical SR of form tape from 105 to 1011 Ω/SQ.
  5. All measurements are in millimeters unless otherwise stated.

Figure 7. SE5012T 16-pin QFN Carrier Tape Dimensions

DATA SHEET • SE5012T: 5 GHz FRONT-END MODULE WITH POWER DETECTOR Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 January 12, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202395D

Ordering Information

Model Name Manufacturing Part Number Evaluation Board Part Number SE5012T: 5 GHz Front-End Module with Power Detector SE5012T SE5012T-EK1 Copyright © 2012-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.