SE2564L SKYWORKS | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 12
Technical content
Features
Dual Mode IEEE802.11b, IEEE802.11g, IEEE802.11n Integrated PA, TX Filter, Diversity switch Integrated Positive Slope Power Detector 20 dBm Output Power, 802.11b, 11 Mbits 17 dBm @ 3.0 % EVM, 802.11g, 3.3V Lead free, halogen free and RoHS compliant Small plated package, 3 mm x 4 mm x 0.9 mm, MSL 1
Ordering Information
Part No. Package Remark SE2564L 24 pin QFN Samples SE2564L-R 24 pin QFN Tape & Reel SE2564L-EK1 N/A Evaluation kit Product Description The SE2564L is a complete 802.11b gn WLAN RF front-end module providing all the functionality of the power amplif ier, power detector, diversity switch and 50 ohm matching on all RF ports . The SE2564L provides a complete 2.4 GHz WLAN RF solution from the output of the transceiver to the antennas in an ultra compact form factor. The SE2564L is designed for ease of use, with all the critical matching and harmonic filtering and integrated transmit/receive D PDT sw itch providing a 50 Ω interface to the antenna. The SE2564L also includes a transmitter power detector with 20 dB of dynamic range and a digital enable control for transmitter power ramp on/off control. The power ramp rise/fall time is 0.5 μs typical. Functional Block Diagram Figure 1: Functional Block Diagram
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 Pin Out Diagram Figure 2: SE2564L Pin Out (Top View Through Package) Pin Out Description Pin No. Name Description Pin No. Name Description
1 Det Power Detector Output 14 C4 Switch Control Logic
2 EN Power Amplifier Enable 15 GND Ground
3 GND Ground 16 ANT1 Antenna 1
4 RF_IN Transmit RF Input 17 GND Ground
5 GND Ground 18 ANT0 Antenna 0
6 GND Ground 19 GND Ground
7 GND Ground 20 VCC0 Supply Voltage
8 GND Ground 21 GND Ground
9 RX Receive RF Output 22 VCC2 Supply Voltage
10 GND Ground 23 GND Ground
11 C1 Switch Control Logic 24 VCC1 Supply Voltage
12 C2 Switch Control Logic
13 C3 Switch Control Logic Paddle GND Ground
RF_IN GND EN
1 DET
Bias, Enable
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside t he recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage on VCC -0.3 5.5 V VIN DC input on EN, C1, C2, C3, C4 -0.3 3.6 V TX RF Input Power. ANT0 and ANT1 terminated in 50Ω match - 12.0 dBm TA Operating Temperature Range -30 85 °C TSTG Storage Temperature Range -40 150 °C ESD HBM JEDEC JESD22-A114 all pins - 150 V ESD CDM JESD22-C101E all pins - 300 V Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit TA Ambient temperature -30 25 85 °C VCC VCC1, VCC2 supply voltage 2.9 3.3 5.5 V VCC0 supply voltage (may use GPIO) 2.7 - 3.6 V Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit ICC-G Total Supply Current POUT = 17 dBm, 54 Mbps OFDM signal, 64QAM - 130 - mA ICC-B Total Supply Current POUT = 19 dBm, 11 Mbps CCK signal, BT = 0.45 - 160 - mA ICQ Total Supply Current No RF - 85 - mA Icntl Control Line Current C1, C2, C3 or C4 = 3.3V 1 10 μA Icc0 Supply Current on VCC0 No RF, VCC0 = 3.3V - 70 100 μA ICC_OFF Total Supply Current No RF Applied, EN = R0 = T0 = T1 = R1 = VCC0 = 0 V - 1 10 μA No RF Applied, EN = R0 = T0 = T1 = R1 = 0 V; VCC0 = 3.3V - 71 110 μA
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 PA Logic Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage (Module On) - 1.8 3.3 3.6 V VENL Logic Low Voltage (Module Off) - 0 - 0.4 V IENH Input Current Logic High Voltage - - 2 10 μA IENL Input Current Logic Low Voltage - - 2 10 μA Switch Logic Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VCTL_ON Control Voltage (On State) - 3.0 - 3.6 V VCTL_OFF Control Voltage (OFF State) - 0.0 - 0.2 V ON Low Loss Switch Control Voltage High State = VCTL_ON - VCTL_OFF 2.7 - 3.6 V OFF High Loss Switch Control Voltage Low State = V CTL_OFF - VCTL_OFF 0 - 0.3 V CCTL Control Input Capacitance - - - 100 pF
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 Switch Control Logic Table Switch Logic Operational Mode C1 C2 C3 C4 TX – ANT0 TX – ANT1 RX – ANT0 RX – ANT1 ON ON ON ON ON OFF OFF OFF OFF ON ON ON OFF OFF ON OFF ON ON ON OFF OFF ON OFF OFF OFF ON ON OFF OFF OFF OFF ON ON OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF ON OFF OFF ON OFF ON ON OFF OFF ON OFF OFF ON OFF OFF ON ON OFF ON ON OFF All other configurations All switches set to OFF
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 802.11g/n Transmit Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit FIN Frequency Range - 2400 - 2500 MHz POUT Output Power
54 Mbps OFDM signal, 64
QAM, 3% Static EVM - 17 - dBm 3% Dynamic EVM - 17 - ACPR, IEEE Mask Spectral Mask POUT = 20 dBm, 11 Mbps CCK, BT = 0.45 11 – 22 MHz 22 – 33 MHz -35 -55 - dBc P1dB P1dB - - 23.0 - dBm S21 Small Signal Gain - 24 27 30 dB ΔS21 Small Signal Gain Variation Gain variation over single 40MHz channel Gain Variation over band 0.5 1.0 dB S213.2 Gain @ limit at Ref- vco spur frequency 3206 to 3312 MHz - - 15 dB Harmonics POUT = 19 dBm, 1 Mbps, CCK - -50 -45 dBm/MHz 3f - -50 -45 dBm/MHz tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - 0.7 - μs S11 Input Return Loss - 10 14 - dB STAB Stability CW, POUT = 20 dBm
0.1 GHz – 20 GHz
Load VSWR = 6:1 All non-harmonically related outputs less than -42 dBm/MHz RU Ruggedness PIN = 12dBm, Load VSWR = 6:1 No permanent damage
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 Receive Characteristics Conditions: VCC = 3.3 V, EN = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit FOUT Frequency Range - 2400 - 2500 MHz RXIL Insertion Loss - - 0.9 1.2 dB RXRL Return Loss - 10 15 - dB Delta Rx Delta between Rx paths ANT0 to RX or ANT1 to RX - - 0.5 dB Ton/off T/R on/off switching speed Switching speed between T/R modes. Vcc0=3.3V. 100 250 nSec TRISO Tx to Rx Leakage Device transmitting (EN = 3.3 V) with 17.0 dBm. @ ANT0 or ANT1, Power measured @ RX TX ↔ ANT0 or ANT1 = ON, RX ↔ ANT0 or ANT1= OFF - -3 0 dBm ANTRISOL Isolation between ANT0 and ANT1 Difference in transmitted signal level on ANT1 or ANT0 while transmistting from ANT0 or ANT1. TX ↔ ANT0 or ANT1 = ON, Rx and opposite ANT port terminated in 50ohm. 18 25 - dB
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 Power Detector Characteristics Conditions: VCC = EN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2564L-EK1 evaluation board, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit FOUT Frequency Range - 2400 - 2500 MHz PDR Power detect range, CW Measured at ANT0 or ANT1 0 - 21 dBm PDZsrc DC source impedance on PD_OUT - - 1 - kΩ PDVNoRF Output Voltage, POUT = No RF Measured into 1MΩ - 0.12 - V PDVp18 Output Voltage, POUT = 17 dBm CW Measured into 1MΩ - 0.45 - V PDVp21 Output Voltage, POUT = 21 dBm CW Measured into 1MΩ - 0.75 - V LPF-3dB Power detect low pass filter -3dB corner frequency PDCLOAD = 390 pF 270 290 400 kHz
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 10 Package Handling Information Because of its s ensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2564L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually att ached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 “ESD Control Policy”, Document Number SQ03-0062 Branding Information Figure 6: SE2564L Branding and Pin 1 Location SiGe 2564L Lot Lot Code Part Pin 1 Designator Pin 1 Terminal Finish Caution! Class 0 ESD sensitive device
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 11 Tape and Reel Information Parameter Value Devices Per Reel 3000 Reel Diameter 13 inches Tape Width 12 millimeters Figure 7: SE2564L-R Tape and Reel Information
SE2564L: 2.4 GHz High Efficiency Wireless LAN Front-End Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202423A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 12 Document Change History Revision Date Notes
1.0 Jun 19, 2009 Created
1.1 Jul 8, 2009 Added ISO label
1.2 Aug 18, 2009 Added Solder and Land Pattern
1.3 Sep 4, 2009 Updated Total Leakage Current in OFF state
Corrected Pinout Definition
1.4 Sep 18, 2009 Add Tape and Reel information
1.5 Sep 23, 2009 Add Dynamic EVM specification
1.6 Sep 29, 2009 Removed reference to pull down resistor, updated leakage current
1.7 Jan 21, 2010 Added ESD warning
1.8 Jan 29, 2010 Removed reference to incorrect part number
1.9 Jun 9, 2010 Updated MSL rating from MSL 3 to MSL 1
2.0 Nov 19, 2010 Updated recommended operating temperature range
2.1 Mar 7, 2012 Remove “Preliminary” from datasheet status.
2.2 Apr 10, 2012 Updated with Skyworks logo and disclaimer statement
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoev er for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this docume nt. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, e xcept as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTOR Y, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON -INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, T EXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life -sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such a pplications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications . Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, I nc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.