SE2433T SKYWORKS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 13
Technical content
Table 1. SE2433T Signal Descriptions (Note 1)
1 B2 Connect through bias resistor to Pin 11,
2 B1 Connect through bias resistor to Pin 11,
3 VCC1 Power supply. Connect to positive supply. 9 RFOUT RF output port.
4 RFIN Input port, Connect to 50 Ω single-ended RF
Note 1: The N/C pins can be connected to ground, but the DNC pin should be left floating. characteristics are shown in Tables 4 and 5. Table 2. SE2433T Absolute Maximum Ratings (Note 1) limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SE2433T Recommended Operating Conditions Table 4. SE2433T Electrical Specifications: DC Electrical Characteristics Table 5. SE2433T Electrical Specifications: AC Electrical Characteristics Note 2: IEEE 802.15.4 source. Note 3: From 50% of PAEN edge to 90% of final RF output power. Note 4: From 50% of PAEN edge to 10% of final RF output power. Note 6: Using recommended out put matching network.
Table 6. SE2433T Logic Characteristics Table 7. SE2433T Logic Controls
0 PA disabled 0
1 PA enabled 1
Note 1: Logic ‘0’ level compliant to V IL as specified in Table 6. Note 2: Logic ‘1’ level compliant to V IH as specified in Table 6.
Figure 3. POUT and ICC VS PIN, CW Figure 5. Small Signal Gain vs Frequency, CW
2400 MHz
2440 MHz
2483 MHz
Figure 7. PAE vs POUT, CW Figure 4. Gain vs POUT, CW Figure 6. ICC vs POUT, CW Figure 8. Gain vs POUT and VCC, CW
Figure 9. 2nd Harmonic vs POUT, Zigbee
2402 MHz
2441 MHz
2480 MHz
Figure 11. BT ACPR CH−2 vs POUT, BT-BDR-DH1 Figure 13. BT ACPR CH+2 vs POUT, BT-BDR-DH1 Figure 10. 3rd Harmonic vs POUT, Zigbee Figure 12. BT ACPR CH−3 VS POUT, BT-BDR-DH1 Figure 14. BT ACPR CH+3 vs POUT, BT-BDR-DH1
Table 8. SE2433T Evaluation Board Bill of Materials Figure 19. Package dimensions for the are shown in Figure 20, and tape and reel dimensions are provided in Figure 21. moisture after the container seal is broken must be followed. Solder Reflow Information, document number 200164. done manually or in a production solder reflow environment.
0.20 Typ
- All dimensions are in millimeters.
- Dimensions and tolerances per ASME 14.5M–1994.
- Unless specified, dimensions are symmetrical about center lines.
- Via hole recommendations:
0.025 mm Cu via wall plating (minimum), via holes to be filled with conductive paste and plated over. 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release.
- Solder mask recommendations:
Contact board fabricator for recommended solder mask offset and tolerance.
0.30 Typ
0.50 Typ
0.400 Typ
0.60 Typ
Figure 18. SE2433T Recommended Land and Solder Patterns
Figure 19. Typical Part Markings
0.10 M C A B
12 Places
- All measurements are in millimeters.
- Dimensions and tolerances according to ASME Y14.5M-2009.
- Unless otherwise specified, the following values apply:
- Coplanarity applies to the terminals as well as all other bottom surface metallization.
- Dimension applies to metallized terminal. If terminal tip has a radius, dimension
should not be measured in that radius area.
- Unless specified, dimensions are symmetrical about center lines.
0.05 M C
0.152 Ref
Figure 20. SE2433T Package Dimensions
- Carrier tape must meet all requirements of Skyworks GP01-D233 procurement spec for tape and reel shipping.
- Carrier tape: black conductive polystyrene.
- Cover tape: transparent conductive material.
- Measured from center line of sprocket hole to center line of pocket.
- Ten-sprocket hole pitch cumulative tolerance: ±0.20 mm.
- All measurements are in millimeters.
Figure 21. SE2433T Tape and Reel Dimensions
DATA SHEET • SE2433T: 2.4 GHz POWER AMPLIFIER Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202411F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 7, 2015 13
Ordering Information
Model Name Manufacturing Part Number Evaluation Board Part Number SE2433T: 2.4 GHz Power Amplifier SE2433T-R SE2433T-EK1 Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.