DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

Features

 Fully supports Quick Charge 2.0 specification  Class A: 5 V , 9 V , and 12 V output voltage  Class B: 5 V , 9 V , 12 V , a nd 20 V output voltage  USB battery charging specification revision 1.2 compatible  Automatic USB DCP shorting D+ to D- line  Default 5 V mode operation  Very low power consumption  Less than 1 mW at 5 V output  Fail safe operation  Adjacent pin-to-pin short-circuit fault  Open circuit pin fault

Applications

 Adaptors for smart phones, tablets, netbooks, digital cameras, and bluetooth accessories  Portable Battery Packs supporting QC.20 functions  Car Cargers supporting QC2.0 functions  Ogther USB power output ports supporting QC2.0 functions

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 3 9/4/2012 SE100 QC2.0 Interface Module Typical Application Pin Description NO. Pin Name Pin Function Description

1 GND Ground

2 V1 Open Drain input of output voltage adjustment switch. Active for 9 V, 12 V, and 20 V output setting. 3 V2 Open Drain input of output voltage adjustment switch. Active for 12 V, and 20 V output setting. 4 V3 Open Drain input of output voltage adjustment switch. Active for 20 V output setting. 5 D- USB D- data line input. 6 D+ USB D+ data line input. 7 R Connected to internal band-gap reference. Provides reference current through connected resistor.

8 BP Connection point for an external bypass capacitor for the internally generated supply

voltage.

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 4 9/4/2012 SE100 QC2.0 Interface Module Functional Block Diagram Absolute Maximum Ratin gs Symbol Parameter Maximum Units VBP BYPASS Pin Voltage 5.6 V VR REFERENCE Pin Voltage 5 V VV1/V2/V3 V1/V2/V3 Pin Voltage VBP V VD+/D- D+/D- Pin Voltage 5 V IBP BYPASS Pin Current 15 mA I V1/V2/V3 V1/V2/V3 Pin Current 0.5 mA I D+/D- D+/D- Pin Current 1 mA Note：VV1/V2/V3 电压不能大于 VBP Recommended Operating Conditions

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 5 9/4/2012 SE100 QC2.0 Interface Module Symbol Parameter Maximum Units TJ Operating Junction Temperature -20 to 125 ℃ TA Operating Ambient Temperature -20 to 85 ℃ Ts Storage Temperature -65 to150 ℃ Lead Temperature (less than 15 seconds) 260 ℃

Electrical Characteristics

（Vcc=5V； Tj=25℃ unless otherwise specified） Symbol Parameter Test Conditions Min Typ Max Unit VBP BYPASS Pin Voltage 4 5 V VBP（reset） Power-Up Reset Threshold Voltage 3.8 V IBPSC BYPASS Pin Source Current VBP = 4.3 V, T J = 25 °CN1 = N2 = N3 = Off 140 μA IBP(SHUNT) BYPASS Pin Shunt Voltage IBP=3mA 5.0 5.3 5.6 V VR REFERENCE Pin Voltage 1.22 1.27 1.32 V VDAT(REF) Data Detect Voltage 0.325 V VSEL(REF) Output Voltage Selection Reference 2 V VINH 12 V / 20 V Output Inhibit Threshold VBP-0.8 V IDAT(SHORT) Data Lines Short -Circuit Delay VOUT ≥ 0.8 V 18 μs TGLITCH D+ High Glitch Filter Time 1250 ms TGLITCH(V) CHANGE Output Voltage Glitch Filter Time 32 ms RDM(DWN) D- Pull-Down Resistance 19.53 Ω RDS(ON)N1 Switch N1 On-Resistance IN1=200μA 300 Ω RDS(ON)N2 Switch N2 On-Resistance IN2=200μA 300 Ω RDS(ON)N3 Switch N3 On-Resistance IN3=200μA 300 Ω RDS(ON)N4 Switch N4 On-Resistance IN4=200μA 300 Ω RDSN5 Switch N5 On-Resistance IN1=200μA，VD+≤3.6V 40 Ω

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 6 9/4/2012 SE100 QC2.0 Interface Module Typical Performance Characteristics 握手完成后，D+,D-输入 0.6V；D+由 0.6V 升到 3.3V，V1 打开 握手完成后，D+，D-输入 0.6V；D+由 0.6 升到 3.3V，V1 打开，D+由 3.3V 下降到 0.6V,V1/V2 打开 握手完成后，D+，D-输入 0.6V;D+由 0.6升 到 3.3V，V1 打开，D-由 0.6 升到 3.3V， V1/V2/V3 打开

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 8 9/4/2012 SE100 QC2.0 Interface Module above V DA T(REF) (typ. 0.325 V) and below VSEL(REF) (typ. 2 V) for at least 1.25 seconds SE100 will enter Quick Charge 2.0 operation mode. If the voltage at D+ drops any time below 0.325 V SE100 resets the 1.25 seconds timer and stays in USB Battery Charging Specification 1.2 compatibility mode with a default output voltage of 5 V . Once SE100 has entered Quick Charge 2.0 operation mode switch N5 will be turned off. Additionally switch N4 is turned on connecting a 19.53 kΩ pull -down resistor to D -. As soon as the voltage at D- has dropped low (<0.325 V) for at least 1 ms SE100 starts accepting requests for different AC -DC adapter output voltages by means of applied voltage levels at data l ines D+ and D - through the powered device. Table 1 summarizes the output voltage lookup table, corresponding AC -DC adapter output voltages and status of switches N1 to N3. For Quick Charge 2.0 Class A support only, the V3 pin has to be connected to the B YPASS pin (directly or through a resistor up to 100 kΩ). This will inhibit any requests for setting a 20 V output. is pulled down by resistor R DAT(LKG) (see Figure 1). Once it drops below 0.325 V SE100 will turn on switch N5 (thereby short -circuiting D+ and D-) and turns off switches N1 to N4. This sets the default output voltage of 5 V . The recommended value for RDAT(LKG) = 390 kΩ. V o1(5V)=VFB*((R1/R2)+1); Vo2(9V)= VFB*((R1/ RX1)+1), RX1=R2//R3; Vo3(12V)= VFB*((R1/ RX2)+1), RX2=RX1//R4; Vo4(20V)= VFB*((R1/ RX3)+1), RX3=RX2//R5;

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 9 9/4/2012 SE100 QC2.0 Interface Module OUTLINE DRAWING SOT-23-6L OUTLINE DRAWING SOP-8 4 5 H E D A B C MIN MAX MIN MAX A 0.0532 0.0688 1.35 1.75 A1 0.0040 0.0098 0.10 0.25 B 0.0130 0.0200 0.33 0.51 C 0.0075 0.0098 0.19 0.25 D 0.1890 0.1968 4.80 5.00 H 0.2284 0.2440 5.80 6.20 E 0.1497 0.1574 3.80 4.00 DIMENSIONS 0.050 BSC 1.27 BSC DIMN INCHES MM

Rev1.0 Preliminary and all contents are subject to change without prior notice. © Seaward Electr onics, Inc., • www.seawardinc.com • Page 10 9/4/2012 SE100 QC2.0 Interface Module 联系方式： 北京思旺电子技术有限公司–中国总部 地址：中国北京市海淀区信息路 22 号上地科技综合楼 B 座二层 邮编：100085 电话:010-82895700/1/5 传真:010-82895706 Seaward Electronics Corporation – 台湾办事处 2F, #181, Sec. 3, Minquan East Rd, Taipei, Taiwan R.O.C 电话: 886-2-2712-0307 传真: 886-2-2712-0191 Seaward Electronics Incorporated – 北美办事处 1512 Centre Pointe Dr. Milpitas, CA95035, USA 电话: 1-408-821-6600