SCM0100200

SCM0100200 CELDUC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Proud to serve youProud to serve youProud to serve youProud to serve you Data given at Tambient=40°C and subject to modification without previous notice celduc r e l a i s celduc r e l a i s S/CON/SCM0100200/D/28/11/03 Page 1/5 GB MOSFET BASED DC SOLID STATE RELAY SCM0100200 Control voltage range 4.5-32VDC Max. output peak voltage 200VDC ! Latest MOSFET technology generation. ! Ultra low on-state resistance. ! New innovative isolated driver ensuring fast power transistor turn on and off therefore low power transient. ! Ultra low output leakage current ! Low control current consumption ! Triggered control input to avoid linear control risks ! Low conducted and radiated disturbances Nom. load current with heatsink 100ADC Load voltage range Load current range Control input voltage range In & case / Out Insulation Connections Dimensions (WxHxD) Weight Depends on protection clamping voltage 0 to 100A (with heatsink) 4.5-32VDC 4kV M3 round tabs M5 round tabs 44.5 x 58.2 x 27 (mm) 100g Fig. 1 HIGH SIDE WIRING DIAGRAM (Load connected to “-“) Fig. 2 LOW SIDE WIRING DIAGRAM (Load connected to “+”) See Instruction sheet for selective the right protective components See Instruction sheet for selective the right protective components Fig. 3 INTERNAL DIAGRAM

S/CON/SCM0100200/D/28/11/03 Page 2/5 GB CONTROL INPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Control voltage range Uc 4.5 – 32VDC Current consumption Ic 25 – 42mADC for control voltage range See fig. 5 Typical turn on voltage Ucontyp 4.3V Min. releasing voltage Ucoffmin 1VDC Typical releasing voltage Ucofftyp 3.5V Max. input voltage Ucmax 32VDC Max. reverse voltage -Ucmax 32VDC Max. reverse leakage current -Icmax 100µA INPUT CIRCUIT Input impedance Re Current limitation See fig. 5 POWER OUTPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Mains voltage range Ue Depends on protection clamping voltage Non-repetitive peak voltage Uep 200V Overvoltage protection D1 Not integrated A voltage clamping mean must be connected across the terminals 1 & 2 (see fig 1 & 2) See Instruction sheet for selective the right protective components Reverse voltage (internal diode) -Ue 1,6V @Ie=-100A @Uc=0 Max. repetitive avalanche current Iep 100A Pulse width limited by Tj max Max. single pulse avalanche energy Eep 750mJ @Ue=50V @Ie=Iep Max. repetitive pulse avalanche energy Eep 58mJ @Ie=56A Resistive Motor Maximum nominal currents Ie 100A Please consult us See fig. 7 for limits Values with heatsink Non-repetitive peak overload current Iepeak 400A @Ue=100VDC L (load+line)=10µH See fig. 8 Min. load current Iemin 0mA Max. leakage current Ielk 250µADC @Uep @Tjmax Max. on-state resistance RDSon 22mΩ @Iemax @Tjmax Typ. output capacitance Cout 1.5nF Junction/case thermal resistance per power element Rthjc 0.4K/W Total = 2 power elements Built-in heatsink thermal resistance vertically mounted Rthra 8K/W @∆Tra=60°C Heatsink thermal time constant Tthra 10min @∆Tra=60°C Control inputs/power ouputs insulation voltage Uimp 4kV Inputs/case insulation voltage Uimp 4kV Outputs/case insulation voltage Uimp 4kV Isolation resistance Rio 1GΩ Isolation capacitance Cio <8pF Maximum junction temperature Tjmax 175°C Storage ambient temperature Tstg -40->+100°C Operating ambient temperature Tamb -40->+90°C See fig. 7 POWER CIRCUIT Max. case temperature Tc 100°C

S/CON/SCM0100200/D/28/11/03 Page 3/5 GB TIME CHARACTERISTICS Fig. 4 TIME DIAGRAMS CHARACTERISTIC LABEL VALUE INFO. Turn on time ton 10µs (1.2µs typical) Turn on delay tdon 600µs (500µs typical) Turn off time toff 10µs (1µs typical) Turn off delay tdoff 100µs (60µs typical) TIME CHARACT.Max. On-Off frequency F(on-off) 700Hz GENERAL INFORMATION Connections Power Control Screwdriver advised Philips™ NR2 Philips™ NR1 Min and max tightening torque 1.8 N.m 0.8 N.m CONNEC- TIONSInsulated crimp terminals (round tabs, eyelet type) M5 M3 Display Green LED (indicates relay has switched ON) Housing UL94V0 Mounting 2 screws (M4x12mm) See mounting sheet Noise level No audible noise MISC. Weight 100g STANDARDS Standards IEC60947-1 Protection level IP00 Protection against direct touch None CE marking Yes GENERALUL, cULUS and VDE approvals Pending TYPE OF TEST STANDARD LEVEL EFFECT E.S.D. (Electrostatic discharges) EN61000-4-2 Pending ? Radiated electromagnetic fields EN61000-4-3 Pending ? Fast transients bursts EN61000-4-4 4kV coupling by clamp on the input side and direct for power side No effect Electric chocks EN61000-4-5 1kV direct coupling on the input side (pending for power side) ? E.M.C. IMMUNITY Voltage drop EN61000-4-11 - E.M.C. EMISSION Radiated and conducted disturbances NFEN55011 Pending

S/CON/SCM0100200/D/28/11/03 Page 4/5 GB CHARACTERISTIC CURVES Fig. 5 INPUT CHARACTERISTIC Fig. 6 ON RESISTANCE VS TEMPERATURE @25°C 0 2 4 6 8 1 01 21 41 61 82 02 22 42 62 83 03 2 Uc (VDC) Ic (mADC) -50 0 50 100 150 Junction Temperature (°C) RDSon (mOhms) Fig. 7 POWER DISSIPATED AND LOAD CURRENT LIMIT VS TEMPERATURE 100 110 0 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 79.2 35.2 8.8 141 220 19.8 2.2 108 178 266 1.2K/W Fig. 8 CURRENT OVERLOAD CHARACTERISTIC (ITSM PER POWER ELEMENT) Please consult us for calculation Permanent current Ie AC51 (ARMS) Power dissipated (W) Ambient temperature (°C) 8K/W = No Heatsink 4K/W = No reference 2.4K/W = WF152100 2.2K/W = WF262100 2.2K/W = WF151200 0.3K/W = WF031100 0.2K/W = WF020000 0.1K/W = No reference Please refere to the installation notice for precautions about mounting the device on a heatsink.

S/CON/SCM0100200/D/28/11/03 Page 5/5 GB DIMENSIONS AND ACCESSORIES Fig. 9 DIMENSIONS TOLERANCES: Ø0.3 1+ 2- 4- 3+ Æ4.743.2 47.6 7.5 5.125.4 44.5 58.2 Ø0,5 19.6 22.8 25.8 Fig.

10 ACCESSORIES

www.celduc.com Rue Ampère B.P. 4 42290 SORBIERS - France Phone : 33 (0) 4 77 53 90 21 Fax : 33 (0) 4 77 53 85 51 Email : celduc-relais@celduc.com