SCAN90004 NSC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Features
n 1.5 Gbps data rate per channel n Configurable pre-emphasis drives lossy backplanes and cables n Low output skew and jitter n Hot plug protection n LVDS/CML/LVPECL compatible input, LVDS output n On-chip 100Ω input and output termination n 15 kV ESD protection on LVDS inputs and outputs n IEEE 1149.1 and 1149.6 compliant n Fault Insertion n Single 3.3V supply n Very low power consumption n Industrial -40 to +85˚C temperature range n Small TQFP Package Footprint n Evaluation Kit Available n See DS90LV004 for non-JTAG version 20113001 SCAN90004 Block Diagram 20113002 Pinout - Top View November 2005 SCAN90004 4-Channel LVDS Buffer/Repeater with Pre-Emphasis and IEEE 1149.6 © 2005 National Semiconductor Corporation DS201130 www.national.com
Number I/O, Type Description DIFFERENTIAL INPUTS IN0+ IN0− I, LVDS Channel 0 inverting and non-inverting differential inputs. IN1+ IN1− I, LVDS Channel 1 inverting and non-inverting differential inputs. IN2+ IN2− I, LVDS Channel 2 inverting and non-inverting differential inputs. IN3+ IN3− I, LVDS Channel 3 inverting and non-inverting differential inputs. DIFFERENTIAL OUTPUTS OUT0+ OUT0− O, LVDS Channel 0 inverting and non-inverting differential outputs. (Note 1) OUT1+ OUT1− O, LVDS Channel 1 inverting and non-inverting differential outputs. (Note 1) OUT2+ OUT2− O, LVDS Channel 2 inverting and non-inverting differential outputs. (Note 1) OUT3+ OUT3- O, LVDS Channel 3 inverting and non-inverting differential outputs. (Note 1) DIGITAL CONTROL INTERFACE PWDN 12 I, LVTTL A logic low at PWDN activates the hardware power down mode. PEM0 PEM1 I, LVTTL Pre-emphasis Control Inputs (affects all Channels) TDI 34 I, LVTTL Test Data Input to support IEEE 1149.1 features TDO 35 O, LVTTL Test Data Output to support IEEE 1149.1 features TMS 27 I, LVTTL Test Mode Select to support IEEE 1149.1 features TCK 26 I, LVTTL Test Clock to support IEEE 1149.1 features TRST 25 I, LVTTL Test Reset to support IEEE 1149.1 features POWER V 28, 29, 32, 33 I, Power V DD = 3.3V, ±5% GND 8, 9, 17, 18, 23, 24, 37, 38, 43, I, Power Ground N/C 6, 30, 31, 36 No Connect Note 1: The LVDS outputs do not support a multidrop (BLVDS) environment. The LVDS output characteristics of the SCAN90004 device have been optimized for point-to-point backplane and cable applications. SCAN90004 www.national.com 2
Absolute Maximum Ratings(Note 2) Supply Voltage (VDD) −0.3V to +4.0V CMOS Input Voltage -0.3V to (V DD+0.3V) LVDS Receiver Input Voltage -0.3V to (V DD+0.3V) LVDS Driver Output Voltage -0.3V to (V DD+0.3V) LVDS Output Short Circuit Current +40 mA Junction Temperature +150˚C Storage Temperature −65˚C to +150˚C Lead Temperature (Solder, 4sec) 260˚C Max Pkg Power Capacity @ 25˚C 1.64W Thermal Resistance (θJA) 76˚C/W Package Derating above +25˚C 13.2mW/˚C ESD Last Passing Voltage HBM, 1.5kΩ, 100pF 15kV EIAJ, 0Ω, 200pF 250V Recommended Operating Conditions Supply Voltage (VCC) 3.15V to 3.45V Input Voltage (VI) (Note 3) 0V to V CC Output Voltage (VO) 0 Vt oV CC Operating Temperature (TA) Industrial −40˚C to +85˚C Note 2: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recom- mend operation of products outside of recommended operation conditions. Note 3: V ID max < 2.4V
Electrical Characteristics
Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter Conditions Min Typ (Note 4) Max Units LVTTL DC SPECIFICATIONS(PWDN, PEM0, PEM1, TDI, TDO, TCK, TMS, TRST) VIH High Level Input Voltage 2.0 V DD V VIL Low Level Input Voltage GND 0.8 V IIH High Level Input Current V IN =V DD =V DDMAX −10 +10 µA IIL Low Level Input Current V IN =V SS,V DD =V DDMAX −10 +10 µA IILR Low Level Input Current TDI, TMS, TRST -40 -200 µA CIN1 Input Capacitance Any Digital Input Pin to V SS 3.5 pF COUT1 Output Capacitance Any Digital Output Pin to V SS 5.5 pF VCL Input Clamp Voltage I CL = −18 mA −1.5 −0.8 V VOH High Level Output Voltage (TDO) IOH = −12 mA, V DD = 3.15 V 2.4 V IOH = −100 µA, V DD = 3.15 V V DD-0.2 V VOL Low Level Output Voltage (TDO) IOL = 12 mA, V DD = 3.15 V 0.5 V IOL = 100 µA, V DD = 3.15 V 0.2 V IOS Output Short Circuit Current TDO −15 −125 mA IOZ Output TRI-STATE Current TDO −10 +10 µA LVDS INPUT DC SPECIFICATIONS(INn±) VTH Differential Input High Threshold (Note 5) VCM = 0.8V to 3.4V, VDD = 3.45V 0 100 mV VTL Differential Input Low Threshold (Note 5) VCM = 0.8V to 3.4V, VDD = 3.45V −100 0 mV VID Differential Input Voltage V CM = 0.8V to 3.4V, V DD = 3.45V 100 2400 mV VCMR Common Mode Voltage Range V ID = 150 mV, V DD = 3.45V 0.05 3.40 V CIN2 Input Capacitance IN+ or IN− to V SS 3.5 pF IIN Input Current V IN = 3.45V, VDD =V DDMAX −10 +10 µA VIN = 0V, VDD =V DDMAX −10 +10 µA SCAN90004 www.national.com3
Electrical Characteristics (Continued) Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter Conditions Min Typ (Note 4) Max Units LVDS OUTPUT DC SPECIFICATIONS(OUTn±) VOD Differential Output Voltage, 0% Pre-emphasis (Note 5) RL = 100Ω between OUT+ and OUT− 250 500 600 mV ∆VOD Change in VOD between Complementary States -35 35 mV VOS Offset Voltage (Note 6) 1.05 1.18 1.475 V ∆VOS Change in VOS between Complementary States -35 35 mV IOS Output Short Circuit Current OUT+ or OUT− Short to GND −60 −90 mA COUT2 Output Capacitance OUT+ or OUT− to GND when TRI-STATE 5.5 pF SUPPLY CURRENT (Static) I CC Supply Current All inputs and outputs enabled and active, terminated with differential load of 100 Ω between OUT+ and OUT-. 117 140 mA ICCZ Supply Current - Power Down Mode PWDN = L 2.7 6 mA SWITCHING CHARACTERISTICS — LVDS OUTPUTS tLHT Differential Low to High Transition Time Use an alternating 1 and 0 pattern at 200 Mb/s, measure between 20% and 80% of V OD. 210 300 ps tHLT Differential High to Low Transition Time 210 300 ps tPLHD Differential Low to High Propagation Delay Use an alternating 1 and 0 pattern at 200 Mb/s, measure at 50% V OD between input to output. 2.0 3.2 ns tPHLD Differential High to Low Propagation Delay 2.0 3.2 ns tSKD1 Pulse Skew |t PLHD–tPHLD|2 5 8 0 p s tSKCC Output Channel to Channel Skew Difference in propagation delay (t PLHD or tPHLD) among all output channels. 50 125 ps tJIT Jitter (0% Pre-emphasis) (Note 7) RJ - Alternating 1 and 0 at 750 MHz (Note 8) 1.1 1.5 psrms DJ - K28.5 Pattern, 1.5 Gbps (Note 9) 43 62 psp-p TJ - PRBS 2 23-1 Pattern, 1.5 Gbps (Note 10) 35 85 psp-p tON LVDS Output Enable Time Time from PWDN to OUT ± change from TRI-STATE to active. 300 ns tOFF LVDS Output Disable Time Time from PWDN to OUT ± change from active to TRI-STATE. 12 ns SCAN90004 www.national.com 4
Electrical Characteristics (Continued) Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter Conditions Min Typ (Note 4) Max Units SWITCHING CHARACTERISTICS — SCAN FEATURES fMAX Maximum TCK Clock Frequency RL = 500Ω, CL =3 5p F
25.0 MHz
tS TDI to TCK, H or L 3.0 ns tH TDI to TCK, H or L 0.5 ns tS TMS to TCK, H or L 2.5 ns tH TMS to TCK, H or L 0.5 ns tW TCK Pulse Width, H or L 10.0 ns tW TRST Pulse Width, L 2.5 ns tREC Recovery Time, TRST to TCK 1.0 ns Note 4: Typical parameters are measured at V DD = 3.3V, TA = 25˚C. They are for reference purposes, and are not production-tested. Note 5: Differential output voltage V OD is defined as ABS(OUT+–OUT−). Differential input voltage V ID is defined as ABS(IN+–IN−). Note 6: Output offset voltage V OS is defined as the average of the LVDS single-ended output voltages at logic high and logic low states. Note 7: Jitter is not production tested, but guaranteed through characterization on a sample basis. Note 8: Random Jitter, or RJ, is measured RMS with a histogram including 1500 histogram window hits. The input voltage = V ID = 500mV, 50% duty cycle at 750MHz, tr =t f = 50ps (20% to 80%). Note 9: Deterministic Jitter, or DJ, is measured to a histogram mean with a sample size of 350 hits. The input voltage = V ID = 500mV, K28.5 pattern at 1.5 Gbps, tr =t f = 50ps (20% to 80%). The K28.5 pattern is repeating bit streams of (00 11111010 1100000101). Note 10: Total Jitter, or TJ, is measured peak to peak with a histogram including 3500 window hits. Stimulus and fixture jitter has been subtracted. The input voltage =V ID = 500mV, 223-1 PRBS pattern at 1.5 Gbps, t r =t f = 50ps (20% to 80%). SCAN90004 www.national.com5
The output characteristics of the SCAN90004 have been optimized for point-to-point backplane and cable applica- tions, and are not intended for multipoint or multidrop signal- ing. POWERDOWN MODE The PWDN input activates a hardware powerdown mode. When the powerdown mode is active (PWDN=L), all input and output buffers and internal bias circuitry are powered off and disabled. Outputs are tri-stated in powerdown mode. JTAG Circuitry is active per the IEEE standard, but does not switch unless TCK is toggling. When exiting powerdown mode, there is a delay associated with turning on bandgap references and input/output buffer circuits as indicated in the LVDS Output Switching Characteristics PRE-EMPHASIS Pre-emphasis dramatically reduces ISI jitter from long or lossy transmission media. Two pins are used to select the pre-emphasis level for all outputs: off, low, medium, or high. Pre-emphasis Control Selection Table PEM1 PEM0 Pre-Emphasis 0 0 Off 0 1 Low 1 0 Medium 1 1 High INPUT FAILSAFE BIASING External pull up and pull down resistors may be used to provide enough of an offset to enable an input failsafe under open-circuit conditions. This configuration ties the positive LVDS input pin to V DD thru a pull up resistor and the negative LVDS input pin is tied to GND by a pull down resistor. The pull up and pull down resistors should be in the 5kΩ to 15kΩ range to minimize loading and waveform distortion to the driver. The common-mode bias point ideally should be set to approximately 1.2V (less than 1.75V) to be compatible with the internal circuitry. Please refer to application note AN- 1194 “Failsafe Biasing of LVDS Interfaces” for more informa- tion. Design-for-Test (DfT) Features IEEE 1149.1 (JTAG) SUPPORT The SCAN90004 supports a fully compliant IEEE 1149.1 interface. The Test Access Port (TAP) provides access to boundary scan cells at each LVTTL I/O on the device for interconnect testing. Differential pins are included in the same boundary scan chain but instead contain IEEE1149.6 cells. IEEE1149.6 is the improved IEEE standard for testing high-speed differential signals. Refer to the BSDL file located on National’s website for the details of the SCAN90004 IEEE 1149.1 implementation. IEEE 1149.6 SUPPORT AC-coupled differential interconnections on very high speed (1+ Gbps) data paths are not testable using traditional IEEE 1149.1 techniques. The IEEE 1149.1 structures and meth- ods are intended to test static (DC-coupled), single ended networks. IEEE1149.6 is specifically designed for testing high-speed differential, including AC coupled networks. The SCAN90004 is intended for high-speed signalling up to 1.5 Gbps and includes IEEE1149.6 on all differential inputs and outputs. FAULT INSERTION Fault Insertion is a technique used to assist in the verification and debug of diagnostic software. During system testing faults are "injected" to simulate hardware failure and thus help verify the monitoring software can detect and diagnose these faults. In the SCAN90004 an IEEE1149.1 "stuck-at" instruction can create a stuck-at condition, either high or low, on any pin or combination of pins. A more detailed descrip- tion of the stuck-at feature can be found in NSC Applications note AN-1313. SCAN90004 www.national.com 6
FIGURE 1. Typical Performance Characteristics of the SCAN90004
Physical Dimensions inches (millimeters) unless otherwise noted 48-TQFP Order Number SCAN90004TVS (250 piece Tray) National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com SCAN90004 4-Channel LVDS Buffer/Repeater with Pre-Emphasis and IEEE 1149.6