SC600-110 SOCAY | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Radial Lead Resettable Polymer PTCs Revision September 12, 2013 2 / 4 @ SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. SC600 Series SOCAY Electronics Co., Ltd. www.socay.com Ambient Operation Temperature -40°C -20°C 0°C 25°C 40°C 50°C 60°C 70°C 85°C Part Number Hold Current (A) A=SC600-110 B=SC600-150 C=SC600-160 D=SC600-200 Temperature Rerating Chart – I hold (A) Temperature Rerating Curve Average Time Current Curves Time in Seconds Current in Amperes Percentage of Rated Current Temperature (°C)
Radial Lead Resettable Polymer PTCs Revision September 12, 2013 3 / 4 @ SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. SC600 Series SOCAY Electronics Co., Ltd. www.socay.com Test Test Conditions Accept/Reject Criteria Resistance In still air @25±2°C Rmin≤R≤Rmax Hold Current 60 min, at Ihold, In still air @25±2°C No trip Time to Trip Specified current, Vmax, @25±2°C T≤Maximum Time To Trip Frequency Current withstand 380V / Imax, 20 cycle Resistance of the variation of the poor value:≤30% Failure mode V maxi / 5A, 60 minute No buming Pre-Heating Zone Refer to the condition recommended by the manufacturer. Max. ramping rate should not exceed 4°C/Sec Soldering Zone Max. solder temperature should not exceed 260°C Cooling Zone Cooling by natural convection in air Lead Material Tin-plated Copper Soldering Characteristics Solder ability per MIL-STD-202, Method 208E Insulating Material Cured, flame retardant epoxy polymer meets UL 94V-0 requirements. Device Labeling Marked with ‘SC’, voltage, current rating Test Procedures and Requirement Part Numbering Part Marking Soldering Parameters Physical Specifications
Radial Lead Resettable Polymer PTCs Revision September 12, 2013 4 / 4 @ SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. SC600 Series SOCAY Electronics Co., Ltd. www.socay.com Figure1 A B C D Lead (dia) Inches mm Inches mm Inches mm Inches mm Part Number Figure Inches Mm Packaging (Bulk Pack) u This product should not be used in an application where the maximum interrupt voltage or maximum interrupt current in a fault condition, Operation beyond the maximum rating or improper use may result in device damage and possible electrical arcing and flame. u A PPTC device is not a fuse, It is a nonlinear thermistor that limits current, Because under a fault condition all PPTC devices go into a high resistance state but not open circuit hazardous voltage may be present at PPTC. u The devices are intended for protection against occasional over-current or over-temperature fault conditions and should not be used when repeated fault conditions or prolonged trip events. u In most application, power must be removed and the fault condition cleared in order to reset a PPTC device. u PPTC devices are not recommended to be installed in applications where the device is constrained such that its PPTC properties are inhibited, for example in rigid potting materials or Add devices surface coating, Bundled devices ontology, which lack adequate clearance to accommodate device expansion. u Contamination on of the PPTC material with certain silicone-based oils or some aggressive solvents can adversely impact the performance of the devices. For example, Organic solvents to cleaning. Dimensions Warning