SC3015B RFM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SC3015B-083004 CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES:
Electrical Characteristics
1, 2 549.89 550.0 550.11 MHz Tolerance from 400.000 MHz ∆fO ±200 ppm Q and Q Output Voltage into 50Ω (VSWR ≤ 1.2) VO 1, 3 0.60 1.1 VP-P Operating Load VSWR 2:1 Symmetry 3, 4, 5 Harmonic Spurious 3, 4, 6 -30 dBc Nonharmonic Spurious -60 dBc Q and Q Period Jitter No Noise on VCC 3, 4, 6, 7 psP-P 200 mVP-P from 1 MHz to ½ fO on 3, 4, 7, 8 psP-P Output (Disabled) Amplitude into 50 Ω 3, 9 mVP-P Output DC Resistance (between Q & Q) KΩ ENABLE (Terminal 14) Input HIGH Voltage VIH 3, 9 VCC-0.1 VCC VCC+0.1 V Input LOW Voltage VIL 0.0 0.20 V Input HIGH Current IIH mA Input LOW Current IIL mA Propagation Delay tPD ms DC Power Supply Operating Voltage VCC 1, 3 +3.13 +3.30 +3.47 VDC Operating Current ICC mA Operating Ambient Temperature TA 1, 3 +70 Lid Symbolization (YY = Year, WW = Week) RFM SC3015B 550.00 MHz YYWW Quartz SAW Frequency Stability Fundamental Fixed Frequency Very Low Jitter and Power Consumption Rugged, Miniature, Surface-Mount Case Low-Voltage Power Supply (3.3 VDC) This digital clock is designed for use with high-speed CPUs and digitizers. Fundamental-mode oscillation is made possible by surface-acoustic-wave (SAW) technology. The design results in low jitter, compact size, and low power consumption. Differential outputs provide a sine wave that is capable of driving 50 Ω loads. Rating Value Units Power Supply Voltage (VCC at Terminal 1) 0 to +4.0 VDC Input Voltage (ENABLE at Terminal 8) 0 to +4.0 VDC Case Temperature (Powered or Storage) -40 to +85
550.0 MHz
Unless otherwise noted, all specifications include any combination of load VSWR, VCC, and TA. In addition, Q and Q are terminated into 50 Ω loads to ground. (See: Typical Test Circuit.) One or more of the following United States patents apply: 4,616,197; 4,670,681; 4,760,352. The design, manufacturing process, and specifications of this device are subject to change without notice. Only under the nominal conditions of 50 Ω load impedance with VSWR ≤ 1.2 and nominal power supply voltage. Symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of Q or Q. (See: Timing Definitions.) Jitter and other spurious outputs induced by externally generated electrical noise on VCC or mechanical vibration are not included. Dedicated external voltage regulation and careful PCB layout are recommended for optimum performance. Applies to period jitter of Q and Q. Measurements are made with the Tektronix CSA803 signal analyzer with at least 1000 samples. Period jitter measured with a 200 mVP-P sine wave swept from 1 MHz to one-half of fO at the VCC power supply terminal. The outputs are enabled when Terminal 8 is at logic HIGH. Propagation delay is defined as the time from the 50% point on the rising edge of ENABLE to the 90% point on the rising edge of the output amplitude or as the fall time from the 50% point to the 10% point. (SEE: Timing Definitions.)
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SC3015B-083004 Electrical Connections Case Design All pads consist of 30 microinches (min) electroless gold on 50 micro- inches (min) electroless nickel over base metal. The metallic center pad was designed for mechanical support. Grounding of this pad is optional. Lid symbolization, including terminal 1 locator dot, are in contrasting ink. Symbolization varies by model number. For purposes of illustration, only terminal 1 dot is shown. Footprint Actual size footprint: Typical Printed Circuit Board Land Pattern A typical land pattern for a circuit board is shown below. Grounding of the metallic center pad is optional. Typical Test Circuit Timing Definitions TOP VIEW A B N J L (X2) D (X8) K (X8) C H G M (X3) E F Typically 0.01" to 0.05" or 0.25 mm to 1.25 mm (8 Places) (The optimum value of this dimension is dependent on the PCB assembly process employed.) Clock Under Test Q Tektronix CSA 803 Digitizing Oscilloscope Ch 2 ENABLE Vcc Q Ch 1 50 Ω Trigger *Power Splitter, Mini-Circuits ZFSC2-4 0.1 µF Sine-Wave Signal Generator 4.7 µH 50 Ω 50 Ω Vcc t PD Propagation Delay: 50% ENABLE Q or Q Output Amplitude Envelope 50% 90% 10% Symmetry: 50% 50% Q or Q Output 50% Symmetry as % of Period Period Symmetry as % of Period t PD Terminal Number Connection VCC Ground NC or Ground Q Output Q Output Ground ENABLE LID Ground Dimensions Millimeters Inches Min Max Min Max A 13.46 13.97 0.530 0.550 B 9.14 9.66 0.360 0.380 C
2.05 Nominal
0.081 Nominal
D
3.56 Nominal
0.141 Nominal
E
2.24 Nominal
0.088 Nominal
F
1.27 Nominal
0.050 Nominal
G
2.54 Nominal
0.100 Nominal
H
3.05 Nominal
0.120 Nominal
J
1.93 Nominal
0.076 Nominal
K
5.54 Nominal
0.218 Nominal
L
4.32 Nominal
0.170 Nominal
M
4.83 Nominal
0.190 Nominal
N