S186ELD BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Class 1 Laser for Use With Banner Modulated Photoelectric Receivers

  • Self-contained Class 1 modulated visible laser diode emitters permit higher gain and extended range in opposed mode sensing systems
  • Narrow effective beam for small-object detection or for precise position control
  • 10 V dc to 30 V dc operation; third wire extinguishes laser light when connected to +V dc
  • Compatible with all EZ-BEAM ® receivers; may also be used with a variety of other Banner modulated photoelectric receivers
  • 18 millimeter threaded barrel design WARNING:
  • Do not use this device for personnel protection
  • Using this device for personnel protection could result in serious injury or death.
  • This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition. Models Model Range Cable1 Supply Voltage Effective Beam at Receiver at 25 °C S186ELD Range varies, depending on which receiver is used (see Excess Gain on page 3) 2 m (6.5 feet) Unterminated

10 V dc to 30 V dc

Opposed Distance Beam Width 1.5 m (5 ft) 4 mm (0.2 in) 3.0 m (10 ft) 5.5 mm (0.2 in) 6.1 m (20 ft) 8.5 mm (0.3 in) 15 m (50 ft) 18 mm (0.7 in) 30 m (100 ft) 32 mm (1.3 in) S186ELDQ 4-wire Euro-style Quick- Disconnect Connector Description of Class 1 Lasers CAUTION:

  • Never stare directly into the sensor lens.
  • Laser light can damage your eyes.
  • Avoid placing any mirror-like object in the beam. Never use a mirror as a retroreflective target. Class 1 Lasers Class 1 lasers are lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Reference IEC 60825-1:2001, Section 8.2. Class 1 Laser Characteristics: Wavelength: 650 nm Pulse Power: ≤ 1 milliwatt Pulse Width: 7 microseconds Rep Rate: 30 microseconds Installation Instructions Mount the Device 1. If a bracket is needed, mount the device onto the bracket. 2. Mount the device (or the device and the bracket) to the machine or equipment at the desired location. Do not tighten the mounting screws at this time. 1 To order the 9 m (30 ft) PVC cable model, add the suffix "W/30" to the cabled model number. For example: S186ELD W/30. Models with a quick disconnect require a mating cordset. S186ELD(Q) Laser Diode Emitter Original Document 35749 Rev. E

15 April 2019

Figure 3. At long distances, use retroreflective tape to locate the beam at the receiver location

10 V dc to 30 V dv (10% maximum ripple) at less than 35 mA

encapsulated. Two mounting nuts are included. deviations pursuant to Laser Notice 50, dated 7-26-01. All measurements are listed in millimeters [inches], unless noted otherwise. Figure 4. Cabled Model Figure 5. Quick-Disconnect Model m (50 ft). For information on compatibility of the S186ELD emitter with other Banner photoelectric receivers, contact Banner Engineering.

4-Pin Threaded M12/Euro-Style Cordsets—Single Ended Model Length Style Dimensions Pinout (Female) MQDC-406 1.83 m (6 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black MQDC-415 4.57 m (15 ft) MQDC-430 9.14 m (30 ft) MQDC-450 15.2 m (50 ft) MQDC-406RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQDC-415RA 4.57 m (15 ft) MQDC-430RA 9.14 m (30 ft) MQDC-450RA 15.2 m (50 ft) Brackets SMB46A

  • 2-piece 12-ga. stainless steel bracket assembly with precision sensor alignment adjustment
  • 2 mm hex key included Hole center spacing: A to B = 18.5, B = 30.5 Hole size: A = ø 6.6, B = 7.1 x 20.3 61 mm 64.5 mm 43 mmAB B SMB18A
  • Right-angle mounting bracket with a curved slot for versatile orientation
  • 12-ga. stainless steel
  • 18 mm sensor mounting hole
  • Clearance for M4 (#8) hardware A B C Hole center spacing: A to B = 24.2 Hole size: A = ø 4.6, B = 17.0 × 4.6, C = ø 18.5 Reflective Tape Model Reflectivity Factor Maximum Temperature Size Unit BRT-THG-4X4-5 102 mm × 102 mm (4 in × 4 in) Package of 5 BRT-THG-8.5X11-2 216 mm × 279 mm (8.5 in × 11 in) Package of 2 BRT-THG-18X36 457 mm × 914 mm (18 in × 36 in) Single Sheet Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. For patent information, see www.bannerengineering.com/patents. S186ELD(Q) Laser Diode Emitter © Banner Engineering Corp. All rights reserved