SA33

SA_1 TSC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Dimensions in inches and (millimeters) - 560 - Version: B07 SA SERIES

500 Watts Transient Voltage Suppressor Diodes

/cuspopen Plastic package has Underwriters Laboratory Flammability Classification 94V-0 /cuspopen 500W surge capability at 10 X 1000us waveform, duty cycle: 0.01% /cuspopen Excellent clamping capability /cuspopen Low zener impedance /cuspopen Fast response time: Typically less than 1.0ps from 0 volts to VBR for unidirectional and 5.0 ns for bidirectional /cuspopen Typical I R less than 1μA above 10V /cuspopen High temperature soldering guaranteed: 260oC / 10 seconds / .375”,(9.5mm) lead length / 5lbs.,(2.3kg) tension M e c h a n i c a l D a t a /cuspopen Case: Molded plastic /cuspopen Lead: Pure tin plated lead free, solderable per MIL-STD-202, Method 208 /cuspopen Polarity: Color band denotes cathode except bipolar /cuspopen Weight: 0.34 gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Type Number Symbol Value Units Peak Power Dissipation at TA=25oC, Tp=1ms (Note 1) PPK Minimum 500 Watts Steady State Power Dissipation at TL=75 oC Lead Lengths .375”, 9.5mm (Note 2) PD 3.0 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) IFSM 70 Amps Maximum Instantaneous Forward Volta ge at 35.0A for Unidirectional Only VF 3.5 Volts Operating and Storage Temperature Range TJ, TSTG -55 to + 175 oC Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25oC Per Fig. 2. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minutes Maximum. Devices for Bipolar Applications 1. For Bidirectional Use C or CA Suffix for Types SA5.0 through Types SA170. 2. Electrical Characteristics Apply in Both Directions.

RATINGS AND CHARACTERISTIC CURVES (SA SERIES) FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY l , PEAK FOR WARD SURGE CURRENT AMPERES FSM 1 10 100 200 100 NUMBER OF CYCLES AT 60Hz 8.3ms Single Half Sine Wave JEDEC Method FIG.1- PEAK PULSE POWER RATING CURVE P , PEAK PULSE POWER, KW PPM 0.1/c109s /c49/c48/c48/c109s /c49/c44/c48/c48/c48/c109s /c49/c48/c44/c48/c48/c48/c109s/c49/c48/c109s/c49/c109s 0.1 tp, PULSE WIDTH, sec. NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 T =25 C A 0 IMPULSE EXPONENTIAL DECAY HALF SINE SQUARE CURRENT WAVEFORM ld ld P PK PPK PPK 5 O ld ld=7lp FIG.3- PULSE WAVEFORMCLAMPING POWER PEAK PULSE CURRENT 0 0 1.0 2.0 3.0 4.0 100 t, TIME, ms PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of l PPM td tr=10 sec./c109 10/1000 sec. WAVEFORM as DEFINED by R.E.A. /c109 PEAK VALUE lPPM HALF VALUE- lPPM 150 FIG.5- TYPICAL JUNCTION CAPACITANCE (UNIDIRECTIONAL) V( ), BREAKDOWN VOLTAGE. VOLTSBR C ,JUNCTION CAP ACITANCE. (pF) J VR=0 Tj =25 C f = 1.0MHz Vsig = 50 mVp-p O MEASURED at STAND-OFF VOLTAGE, V WM 1 10 100 200 100 1000 6000 FIG.2- POWER DERATING CURVE PEAK POWER (Ppp) DERA TING IN PERCENT AGE, % 0 25 50 75 100 125 150 175 200 100 TEMPERATURE, C o Version: B07 1.6 X 1.6 X .040" (40 X 40 X 1mm.) COPPER HEAT SINKS L=0.375"(9.5mm) LEAD LENGTHS T LEAD TEMPERATUREL, T AMBIENT TEMPERATUREA,

Dimensions in inches and (millimeters) ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Device VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature (Volts) (Note 1) @IT VWM at VWM Current IPPM Voltage at IPPM Coefficient Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of V BR mV / OC)

ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Device VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature (Volts) (Note 1) @IT VWM at VWM Current IPPM Voltage at IPPM Coefficient Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of V BR mV /OC) SA90 100 122 1.0 90.0 1.0 3.2 160 121 SA90A 100 111 1.0 90.0 1.0 3.5 146 110 SA100 111 136 1.0 100 1.0 2.9 179 135 SA100A 111 123 1.0 100 1.0 3.2 162 123 SA110 122 149 1.0 110 1.0 2.6 196 148 SA110A 122 135 1.0 110 1.0 2.9 177 133 SA120 133 163 1.0 120 1.0 2.4 214 162 SA120A 133 147 1.0 120 1.0 2.7 193 146 SA130 144 176 1.0 130 1.0 2.2 230 175 SA130A 144 159 1.0 130 1.0 2.5 209 158 SA150 167 204 1.0 150 1.0 1.9 268 203 SA150A 167 185 1.0 150 1.0 2.1 243 184 SA160 178 218 1.0 160 1.0 2.0 257 217 SA160A 178 197 1.0 160 1.0 2.0 259 196 SA170 189 231 1.0 170 1.0 1.7 304 230 SA170A 189 209 1.0 170 1.0 1.9 275 208 Notes: 1. VBR measured after IT applied for 300us, IT = square wave pulse or equivallent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types with VWM of 10 Volts and under, the ID limit is doubled. 4. All terms and symbols are consistent ANSI/IEEE C62.35.