S4012DRP LITTELFUSE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.

12 Amp Standard SCRs

Description

Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes of current at less than 1 .5V potential. Features & Benefits

  • RoHS compliant
  • Glass – passivated junctions
  • Voltage capability up to 1000 V
  • Surge capability up to 120 A Main Features Symbol Value Unit IT(RMS) 12 A VDRM/VRRM 400 to 1000 V IGT 20 mA Schematic Symbol Absolute Maximum Ratings Symbol Parameter Test Conditions Value Unit IT(RMS) RMS on-state current Sxx12R Sxx12D Sxx12V TC = 105°C 12 A IT(AV) Average on-state current Sxx12R Sxx12D Sxx12V TC =105°C 7. 6 A ITSM Peak non-repetitive surge current single half cycle; f = 50Hz; TJ (initial) = 25°C 100 A single half cycle; f = 60Hz; TJ (initial) = 25°C 120 I2t I2t Value for fusing tp = 8.3 ms 60 A2s di/dt Critical rate of rise of on-state current f = 60Hz; TJ = 125°C 100 A/μs IGM Peak gate current TJ = 125°C 2 A PG(AV) Average gate power dissipation TJ = 125°C 0.5 W Tstg Storage temperature range -40 to 150 TJ Operating junction temperature range -40 to 125 Note: xx = voltage

Applications

Typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. Also controls for power tools, home/brown goods and white goods appliances.AK G

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Test Conditions Value Unit IGT VD = 12V RL = 60 Ω MAX. 20 mA VGT MIN. 1 MAX. 1. 5 V dv/dt VD = VDRM; gate open; TJ = 100°C 400V MIN. 350 V/μs 600V 300 800V 250 1000V 100 VD = VDRM; gate open; TJ = 125°C 400V 250 600V 225 800V 200 VGD VD = VDRM RL = 3.3 kΩ TJ = 125°C MIN. 0.2 V IH IT = 200mA (initial) MAX. 40 mA tq IT = 2A; tp = 50µs; dv/dt = 5V/µs; di/dt = 30A/µs MAX. 35 μs tgt IG = 2 x IGT PW = 15µs IT = 20A TYP . 2 μs Static Characteristics Symbol Test Conditions Value Unit VTM IT = 24A; tp = 380 µs MAX. 1. 6 V IDRM / IRRM VDRM = VRRM TJ = 25°C 400 – 600V MAX. μA 800 – 1000V 20 TJ = 100°C 400 – 800V 500 1000V 3000 TJ = 125°C 400 – 800V 1000 Thermal Resistances Symbol Parameter Value Unit Rθ(J-C) Junction to case (AC) Sxx12R 1. 5 °C/WSxx12V 1. 6 Sxx12D 1. 4 Rθ(J-A) Junction to ambient Sxx12R 40 °C/W Sxx12V 70 Note: xx = voltage

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Figure 1: Normalized DC Gate T rigger Current vs. Junction T emperature Figure 2: Normalized DC Gate T rigger Voltage vs. Junction T emperature 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 100 125 Junction Temperature (TJ ) - (°C) Ratio of IGT / IGT (TJ = 25°C) 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ) - (°C) Ratio of VGT / VGT (TJ = 25°C) Figure 5: Power Dissipation (T ypical) vs. RMS On-State Current 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ ) - (°C) Ratio of IH / IH (TJ = 25°C) Figure 3: Normalized DC Holding Current vs. Junction T emperature Figure 4: On-State Current vs. On-State Voltage (T ypical) TJ = 25°C Instantaneous On-state Voltage (vT) – Volts Instantaneous On-state Current (i T) – Amps 0 2 4 6 8 10 12 RMS On-State Current [I T(RMS)] - (Amps) Average On-State Power Dissipation [PD(AV)] - (Watts)

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Figure 6: Maximum Allowable Case T emperature vs. RMS On-State Current Figure 7: Maximum Allowable Case T emperature vs. Average On-State Current 100 105 110 115 120 125 130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0 1 2 3 4 5 6 7 8 Average On-State Current [IT(AVE)] - Amps Maximum Allowable Case Temperature (TC) - °C 100 105 110 115 120 125 130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0 2 4 6 8 10 12 14 RMS On-State Current [IT(RMS)] - Amps Maximum Allowable Case Temperature (TC)- °C Figure 8: Maximum Allowable Ambient T emperature vs. RMS On-State Current 100 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx12V Sxx12R RMS On-State Current [IT(RMS)] - Amps Maximum Allowable Ambient Temperature (TA) - °C Figure 9: Maximum Allowable Ambient T emperature vs. Average On-State Current 100 120 5.10.15.00.0 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx12R Sxx12V Average On-State Current [IT(AVE)] - Amps Maximum Allowable Ambient Temperature (TA) - °C Note: xx = voltage Figure 10: Peak Capacitor Discharge Current 100 1000 0.050.520.55.0 Peak Discharge Current (ITM) - Amps Pulse Current Duration (tw) - ms ITRM tW Figure 11: Peak Capacitor Discharge Current Derating 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 25 50 75 100 125 150 Normalized Peak Current Case Temperature (TC) - °C

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Peak Surge (Non-repetitive) On-state Current (ITSM ) – Amps Surge Current Duration - Full Cycles Figure 12: Surge Peak On-State Current vs. Number of Cycles SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. Soldering Parameters Reflow Condition Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (t p) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Time Temperature TP TL TS(max) TS(min) tP tL tS time to peak temperature PreheatPreheat Ramp-upRamp-up Ramp-downRamp-do

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Physical Specifications Environmental Specifications Test Specifications and Conditions AC Blocking MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours T emperature Cycling MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time T emperature/ Humidity EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity High T emp Storage MIL-STD-750, M-1031, 1008 hours; 150°C Low-T emp Storage 1008 hours; -40°C Thermal Shock MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwell- time at each temperature; 10 sec (max) transfer time between temperature Autoclave EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E T erminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Lead Material Copper Alloy Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting T ab Common with Center Lead Dimension Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1 .52 1 .91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1. 14 1 .52 R 0.038 0.048 0.97 1 .22 K J A H G B F E C D L R TC MEASURING POINT ANODE O P N M .276 7.01 .526 13.36 .320 8.13 AREA (REF.) 0.17 IN2 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB GATECATHODE ANODE Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm).

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Dimensions — TO-251AA (V/I-Package) — V/I-PAK Through Hole Dimension Inches Millimeters Min Typ Max Min Typ Max AREA: 0.040 IN2TC MEASURING POINT GATE G I E D A B C F J H K L 5.28 .208 5.34 .210 Anode Cathode Anode P Q R S Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount Dimension Inches Millimeters Min Typ Max Min Typ Max M O N HJ L K .118 .063 1.60 .071 1.80 .264 6.71 .264 6.71 .181 4.60 GATE Anode Cathode Anode TC MEASURING POINT G I D E A B C F 5.28 .208 5.34 .210 : 0.040 IN2AREA P Q

Revised: June 24, 2011 04:57 PM ©2011 Littelfuse, Inc T eccor® brand Thyristors Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Gate Sensitivity Type Package 400V 600V 800V 1000V Sxx12R X X X X 20mA Sensitive SCR TO-220R Sxx12V X X X X 20mA Standard SCR TO-251 Sxx12D X X X X 20mA Standard SCR TO-252 Note: xx = voltage Part Number Marking Weight Packing Mode Base Quantity Sxx12R Sxx12R 2.2 g Bulk 500 Sxx12RTP Sxx12R 2.2 g Tube 500 (50 per tube) Sxx12DTP Sxx12D 0.3 g Tube 750 (75 per tube) Sxx12DRP Sxx12D 0.3 g Embossed Carrier 2500 Sxx12VTP Sxx12V 0.4 g Tube 750 (75 per tube) Note: xx = Voltage 0.512 (13.0) Arbor Hole Diameter DC XXXXXX XXXXXX DC XXXXXX DC XXXXXX XX Gate Cathode Anode 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 DIA(1.5) * Cover tape XX XX Direction of Feed Dimensions are in inches (and millimeters). TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards Part Numbering System Part Marking System S 60 12 R 56 DEVICE TYPE S: SCR VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 1000V CURRENT RATING 12: 12A SENSITIVITY & TYPE (blank): 20mA PACKAGE TYPE R: TO-220 Non-Isolated V: TO-251 (V/I-Pak) D: TO-252 (D-Pak) LEAD FORM DIMENSIONS xx: Lead Form Option S6012DRP YMLDD TO-252AA – (D Package) TO-251AA –( V Package) MY S6012RTP