S4580 KODENSHI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • Oper ating voltage. ( ±2V ~ ±18V)
  • Low input noise voltage. (0.8 ㎶ rms typ.)
  • Wide gain bandwidth product. (15MHz typ.)
  • Low distortion. (0.0005% typ.)
  • Slew r ate. (5V/ ㎲ typ.)

Ordering Information

Type NO. Marking Package Code S4580 S4580 SOP-8 Block Diagram

A b s o l u t e m a x i m u m r a t i n g s Ta = 25 °C Characteristic Symbol Ratings Unit Supply voltage V CC ±18 / 32 V Differential input voltage V ID ±30 V Input voltage V IC(note) ±15 V Output current I O ±50 mA Power Dissipation P D 300 mW Operating temperature Topr -40 ~ +85 °C Storage temperature Tstg -40 ~ +125 °C (note) For supply voltage less than ±15V, the absolute maximum input voltage is equal to the supply voltage.

Electrical Characteristics

(Unless otherwise specified. VCC = +15V , VEE=－15V and Ta = 25 °C) Characteristic Symbol Test Condition Min. Typ. Max. Unit Input offset voltage V IOS Rg ≤10 ㏀ - 0.5 3 mV Input offset current I IOS - - 5 200 nA Input bias current I IB - - 100 500 nA Input common mode Voltage Range VICR - ±12 ±13.5 - V VCC=10V, VEE=GND 7.0 8.0 - Maximum Output Voltage V OM RL≥2 ㏀ ±12 ±13.5 - V VCC=10V, VEE=GND, RL≥2 ㏀ 7.0 8.0 - Large signal Voltage Gain G V Vout=±10V, RL≥2 ㏀ 90 110 - dB Common mode rejection ratio CMRR Rg ≤10 ㏀ 80 110 - dB Power supply voltage rejection ratio PSRR Rg ≤10 ㏀ 80 110 - dB Slew Rate SR RL≥2 ㏀ - 5.0 - V/us Supply Current I CC - - 6.0 9.0 mA Equivalent input noise voltage VNI RIAA, RS=2.2 ㏀, f=30 ㎑ LPF - 0.8 - uVrms Total harmonic distortion THD AV=20dB, VO=5V, RL=2 ㏀ Gain bandwidth product GB f=10KHz - 15 - MHz (note) [ Condition : V CC=10V, VEE=GND, RL≥2 ㏀, VIN Offset =5V]

Electrical Characteristic Curves Fig. 1 GV - f Φ Fig. 6 EN - f Fig. 5 VOM - RL Fig. 4 VOM - VCC/VEE Fig. 3 IIB - Ta Fig. 2 V OP-P - f (Vcc/VEE=±15V or VCC/VEE=30V / GND, RL=2 ㏀, 40dBAmp,Ta=25℃) (Vcc/VEE=±15V or VCC/VEE=30V / GND, RL=2 ㏀,Ta=25℃) (Vcc/VEE=±15V) (RL=2 ㏀,Ta=25℃) (Vcc/VEE=±15V ,Ta=25℃) (Vcc/V EE=±15V ,RS=50 ㏀,Av=60dB,Ta=25℃) (℃)

Electrical Characteristic Curves Fig. 12 V IOS - Ta Fig. 7 VOM - Ta Fig. 8 ICC - Ta Fig. 9 VIOS - Ta Fig. 10 ICC - Vcc (Vcc/VEE=±15V) (Vcc/VEE=±15V) (Ta=25℃) (℃) (℃) (℃) Fig. 11 VIOS - Ta (Vcc/VEE=±15V ,RL=2 ㏀)

Electrical Characteristic Curves Fig. 10 I CC - Vcc Fig. 13 VOM - Ta Fig. 15 VIOS - Ta Fig. 16 ICC - Vcc Φ (V+/V- =±15V , Gain=20dB, RL=2 ㏀ (V+/V- =±15V , RL=2 ㏀, 40dBAmp, Ta=25℃)

Package Dimension [Unit : mm] Recommend PCB solder land [SOP-8 / Unit :mm] θ θ

The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication e quipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safet y device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equi pments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice.