S1U-3X-16-A-12-RC

D1U-W-1200-12-HC2C MURATA-PS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 1 of 7 Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com SELECTION GUIDE Part Number Power Output High Line AC Power Output Low Line AC Main Output Standby Output Airflow D1U-W-1200-12-HC2C 1200W 900W 12V 3.3V Back to front D1U-W-1200-12-HA2C 1200W 900W 12V 5V Back to front D1U-W-1200-12-HC1C 1200W 900W 12V 3.3V Front to back D1U-W-1200-12-HA1C 1200W 900W 12V 5V Front to back Part Number Description S1U-3X-16-A-12-RC Power shelf for 12V D1U INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input Voltage Operating Range Low Line AC 90 140 VacHigh Line AC 180 264 Input Frequency 47 50/60 63 Hz Turn-on Input Voltage Ramp up 78.5 86.5 VacTurn-off Input Voltage Ramp down 70.5 78 Maximum Input Current Low Line AC 90Vac 15 ArmsHigh Line AC 180Vac 10 Inrush Current Cold start between 0-1msec 100 Apk Power Factor Output load >90% 95% Output load >50% 75% OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units 12V Voltage Set Point Accuracy 12.12 VdcLine and Load Regulation 11.75 12.48 Ripple Voltage & Noise1 20MHz Bandwidth 120 mV p-p Output Current 0 98.3 A Load Capacitance 40000 μF 3.3Vsb Voltage Set Point Accuracy 3.3 VdcLine and Load Regulation 3.2 3.4 Ripple Voltage & Noise1 20MHz Bandwidth 33 mV p-p Operating Range 0 6 A Load Capacitance 1530 μF 5Vsb Voltage Set Point Accuracy 5 VdcLine and Load Regulation 4.85 5.15 Ripple Voltage & Noise1 20MHz Bandwidth 50 mV p-p Operating Range 0 4 A Load Capacitance 1530 μF

FEATURES

/square6 RoHS compliant /square6 1200W (220Vac), 900W (110Vac) Output power /square6 12V Main output, 3.3V or 5V standby output /square6 1U sized; dimensions 12” x 4.75” x 1.6” /square6 13.2 Watts per cubic inch density /square6 N+1 redundancy capable, including hot-docking /square6 Active current sharing on main output /square6 Over-voltage, over-current, over-temperature protection /square6 Internal cooling fans /square6 I²C Bus Interface with status indicators /square6 Optional 1U x 19” power-shelf PRODUCT OVERVIEW The D1U-W-1200 is a 1200 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 12V and standby output of either 5V or 3.3V. Packaged in 1U low profile, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U-W-1200 is designed to auto-recover from over-temperature faults. Status information is provided with front panel LEDs, logic signals and I 2C management interface. Three units can be packaged into an optional 19” 1U power shelf to provide up to 3.6kW of power. The S1U-X3 is a 1U x 19” EIA Rack Mount Power Shelf designed for holding three D1U Front End Power Supplies in current sharing applications. It is intended for distributed power architecture applications in the Servers, Storage Networking and Data Communications markets. There are two lug terminal connections for #2 AWG cabling for the DC output. System connection through the I 2C bus reports the performance status of the power supplies within the power shelf. Two Power Shelves can operate in parallel by an optional Shelf-to-Shelf cable, doubling the power output to the maximum capability of 7.2kW for two 12V power shelves. 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 2 x 270 uF of OSCON capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. See Ripple Test Setup diagram.

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 2 of 7 OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Remote Sense 120 mV Efficiency 220Vac 90.6 % Output Rise Monotonicity Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up Start-up Time AC ramp up 1.5 s PS_On activated 150 ms Transient Response 12V Ramp 1A/μs, 50% load step ±600 mV3.3Vsb Ramp 1A/μs, 50% load step ±165 5Vsb Ramp 1A/μs, 50% load step ±250 Current sharing accuracy (up to 6 in parallel) At 100% load ±10 % Hot Swap Transients All outputs within regulation Hold-up Time Max. load, nominal Vin 20 ms GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-condensing -40 70 °COperating Temperature Range 05 0 Operating Humidity Non-condensing 10 90 %Storage Humidity 59 0 Shock 30G non operating Sinusoidal Vibration 0.5G, 5 – 500 Hz operating MTBF Calculated per Bellcore at Ta=30°C 200 Khrs Demonstrated 200 Khrs Acoustic ISO 7779-1999 60 dB LpAm Safety Approvals c-CSA-us (CSA 60950-1-03/UL 60950-1, First Edition) TUV approval (Bauart) EN 60950-1:2001 Input Fuse Power Supply has internal 20A/250V fast blow fuse on the AC line input Material Flammability UL 94V-0 Switching Frequency 90KHz for Boost PFC Converter 165KHz for Main Output Converter 200KHz for Standby Output Converter Weight 2.1kg PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Over-temperature Auto-restart 55 65 °C 12V Over Voltage Latching 13 14 V Over Current Latching 107 122 A 3.3Vsb Over Voltage Latching 3.57 4.02 V Over Current Latching 6.5 8 A 5Vsb Over Voltage Latching 5.6 6 V Over Current Latching 5 7 A ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Insulation Safety Rating / Test Voltage Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis Output to Output Material Flammability UL 94V-0 Grounding Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF capacitor is connected between Return and power supply chassis. Main Output Return should be connected to the System Chassis.

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 3 of 7 CONTROL SIGNALS Status Conditions Description LED Off No AC input to all PS Flashing Yellow Power Supply Failure Flashing Green Main Output Absent Green Power Supply Good I 2C Registers Status PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning & shutdown, AC Range Output Fault 12V OV, 12V UV, 12V OC, Vsb Fail, Fan1 Fail, Fan2 Fail 12V Output 8 bit scaled output voltage 12V 8 bit scaled output current Fan1 Monitor 8 bit scaled output current Fan2 Monitor 8 bit scaled output current EMISSIONS AND IMMUNITY Characteristic Description Criteria Harmonics IEC/EN 61000-3-2 Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Emission Conducted FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A, 6dB margin Emission Radiated FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A, 6dB margin ESD IEC/EN 61000-4-2 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge Electromagnetic Field IEC/EN 61000-4-3 Electrical Fast Transients/Burst IEC/EN 61000-4-4 Surge IEC/EN 61000-4-5 1kV/2kV, Performance Criteria B RF Conducted Immunity IEC/EN 61000-4-6 3 Vac, 80% AM, 1kHz, Performance Criteria A Magnetic Immunity IEC/EN 61000-4-8 3 A/m Voltage dips, interruptions IEC/EN 61000-4-11 RIPPLE TEST SETUP Power Supply AC Phase Load Box ACG round Oscilloscope 20MHz BW BNC to BNC Shielded Cable 2x270uF OSCON General Notes: 1. Load the outputs at specified minimum output current. 2. Connect the probe as shown with the input tip and ground as short as possible. 3. Take all measurements 4. Repeat the measurements with the outputs at specified maximum output current. 0.1uF Ceramic

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 4 of 7 OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: Tyco Part # 1-6450132-2, or FCI PowerBlade # 51732-021 Pin Assignment Signal Name Description High Level Low Level I Max P1, P2, P7, P8 V OUT Main output voltage P3, P4, P5, P6 V RTN Main output voltage, return A1 Sense + VOUT remote sense, positive node input, connected to the +ve load point A2 Sense - VOUT remote sense, negative node input, connected to the -ve load point C5, C6, D5, D6 V_ SB Standby voltage output C3, C4, D3, D4 V_ SB Return Standby voltage, return, tied internally to Output Return B1 I_Share Active load sharing bus 0 – 8V -4 mA / +5 mA D1 AC_OK Input AC Voltage “OK” signal output (Internal pull up is 10kΩ to Vsb) >2.4V (active, OK) <0.4V +4 mA -2 mA D2 P_Good Power good signal output (Internal pull up is 10kΩ to Vsb) >2.4V (active, Good) <0.4V +4 mA -2 mA B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and first-break contact for hot plugging). This signal overrides PS-On in disabling the Main Output >2.1V (open, or Vsb) <0.7V (active, PS:On) N/A B6 PS_Present Internally tied to Vsb return 0 V A6 PS_On Internal 1K ohm pull-up to Vsb, (accepts open collector/ drain drive), This signal to be pulled low to turn-on power supply >2.1V (open, or Vsb) <0.7V (active, PS:On) -4 mA -1 mA A3 I 2C Data I 2C serial data bus Vsb A4 I 2C Clock I 2C serial clock bus Vsb B2 I 2C Adr0 Address input 0, internal pull-up to Vsb >2.1V, < Vsb <0.8V ±1 mA B3 I 2C Adr1 Address input 1, internal pull-up to Vsb >2.1V, <Vsb <0.8V ±1 mA B4 I 2C Adr2 Address input 2, internal pull-up to Vsb >2.1V, <Vsb <0.8V ±1 mA D1U MATING CONNECTORS 12V D1U mat- ing connector Press Fit Solder 2 Straight Right Angle Straight Right Angle MPS N/A N/A N/A 36-0430032-0 FCI 51742-10802400CALF 51762-10802400CBLF 51742-10802400AALF 51762-10802400ABLF Tyco TBD TBD TBD TBD 2 Solder connector recommended for board thickness of <0.090 P1 P2 P3 P4 P5 P6 P7 P8 x1 x2 x3 x4 x5 x6 VOUT VOUT VRTN VRTN VRTN VRTN VOUT VOUT AC_OK P_GOOD V_SB RETURN V_SB RETURN V_SB +OUT V_SB +OUT D SPARE SPARE V_SB RETURN V_SB RETURN V_SB +OUT V_SB +OUT C I_SHARE I 2C ADR0 I 2C ADR1 I 2C ADR2 PS_KILL PS_ PRESENT B SENSE + SENSE - I 2C DATA I2C CLOCK SPARE PS_ON A mate-last pins

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 5 of 7 CONNECTOR TO CUSTOMER SYSTEM Signal Connector: MOLEX # 39-28-5204 OR TYCO # 281282-1 Mating Connector: MOLEX # 0039521204 Pin Assignment Signal Name Description High Level Low Level I Max

1 AC_OK1 1 Input AC Voltage ‘OK’ signal output for the 2nd shelf open drain

< 0.7V - 2 mA + 4 mA

2 P_Good1 2 Power good signal output for the 2nd shelf open drain

< 0.7V - 2 mA + 4 mA 3 PS_On1 3 Power enable for the 2nd shelf > 2.1V (open, or Vsb) < 0.7V (active, PS:On) - 1 mA - 4 mA

4 NOT USED

5 AC_OK0 1 Input AC Voltage “OK” signal output for the local shelf open drain

< 0.7V - 2 mA + 4 mA

6 P_Good0 2 Power good signal output for the local shelf open drain

< 0.7V - 2 mA + 4 mA 7 PS_OnO 3 Power enable for the local shelf > 2.1V (open, or Vsb) < 0.7V (active, PS:On) - 1 mA - 4 mA

8 NOT USED

9I 2C Adr2 Address input 2 > 2.1V, < Vsb < 0.8V ± 1 mA

10 I 2C Clock4 I2C serial clock bus Vsb

11 I 2C Data4 I2C serial data bus Vsb

12 I_SHARE

13 SENSE + 5

14 SENSE - 5

15 Vsb Standby voltage output

16 Vsb Standby voltage output

17 Vsb Standby voltage output

18 GND GROUND

19 GND GROUND

20 GND GROUND

All control signals are with respect to Ground. Negative currents exit the power supply.

1 Signal goes low when any one of the three power supplies loses AC

2 Signal goes low when any one of the three power supplies fail

3 In a standalone shelf (without I2C control) Pull this pin to GND to turn on three power supplies at the same time. With I2C control, leave this signal float and Use I2C to turn on one power supply at a time. 4 Recomended 10KOhm pull up resistor to host 3.3 or 5V rail

5 Short Sense+ to +Vout and Sens- to GND at the point of load

Signal Connector: MOLEX # 39-28-5164 OR TYCO # 281281-1 Pin Assignment Signal Name Description High Level Low Level I Max < 0.7V - 2 mA + 4 mA < 0.7V - 2 mA + 4 mA 3 PS_On1 3 Power enable for the 2nd shelf > 2.1V (open, or Vsb) < 0.7V (active, PS:On) - 1 mA - 4 mA

5 NOT USED

2C Clock4 I2C serial clock bus Vsb 7I 2C Data4 I2C serial data bus Vsb

8 I_SHARE

9 SENSE + 5

10 SENSE - 5

11 Vsb Standby voltage output

12 Vsb Standby voltage output

13 Vsb Standby voltage output

14 GND GROUND

15 GND GROUND

16 GND GROUND

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 6 of 7 MECHANICAL DIMENSIONS - D1U-W-1200-12-Hx MECHANICAL DIMENSIONS - S1U Power Shelf REF 8,890.350[] (465.00) 18.307 (5.80) 0.228 (31.80) 1.252 (43.40) 1.709 (482.40) 18.992 (404.80) 15.937 (439.80) 17.315 NOTES: 1. The DC output terminals are of terminal block style that will allow connection using crimp type right-angle lugs accepting up to AWG#2 wire, Panduit lug LCC2-14AWF-Q or equivalent is recommended. 2. Two M6 studs at 15.88 mm centre spacing are provided for connection to each pole. Hardware is provided for fastening the lugs/wires as well as terminal block covers

Technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232www.murata-ps.com D1U-W-1200-12-Hx Series AC/DC Front End Power Supply + S1U Power Shelf CPS_D1U-W-1200-12-Hx.C06 Page 7 of 7 S1U PIN CONNECTORS - BACK VIEW SHELF TO SHELF CONNECTION OPTIONAL ACCESSORIES Description Part Number 12V D1U output connector card D1U-12-CONC Shelf to shelf cable 535-413-1537-1 APPLICATION NOTES Document Number Description ACAN-27 Output Connector Card ACAN-29 D1U Communication Protocol J1 SIGNAL CONNECTOR TO CUSTOMER SYSTEM J2 TO J1 RIBBON CABLE P/N 535-413-1537-1 ( REPEAT THIS CONNECTION FOR ADDITIONAL SHELVES. ) J2 SIGNAL CONNECTOR FOR SHELF-TO-SHELF CONNECTION USE CABLE P/N 535-413-1537-1 J1 SIGNAL CONNECTOR TO CUSTOMER SYSTEM 12V+ OUTPUT GNDGND 12V+ OUTPUT PIN #1PIN #1 01/22/09 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2009 Murata Power Solutions, Inc. USA: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Canada: Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com UK: Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Germany: München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Japan: Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com China: Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Singapore: Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED