RV7-2405S20A1W RSG | Alldatasheet

Document overview

  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 DC/DC-Converter RV7-S20W/D20W 20W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

  • 1“ x 1“ Package
  • Wide 4:1 Input Range
  • Soft Start
  • No Minimum Load Required
  • Adjustable Output Voltage
  • Over Current Protection
  • Over Voltage Protection
  • 1600VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 89%
  • Operating Temperature Range -40° ~ +75°C
  • Remote On/Off Control (CTRL) OUTPUT SPECIFICATION Voltage accuracy: ±1% Output Voltage Adjustability (Trim): Singel Output: ±10% max. Line regulation: Single &Dual ±0.5% max. LOAD REGULATION: Singel: ±0.5% max. Dual: ±1%,max.(balanced load) Cross Regulation (Dual Output): ±5% Over Voltage Protection (Zener diode clamp): Over Current Protection: 140% of Fl, typ. Short Circuit Protection : Indefinite (hiccup) (Automatic Recovery) Ripple noise (20Mhz bandwidth): 75-100mV pk-pk max. Temperature coefficient: ±0.02%°C Capacitor load: See table Transient Recovery Time: 250us, typ. Transient Response: ( Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 30ms, typ. No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 30mA pk-pk Remote On/Off (positive logic): On: 3.0~12VDC or open circuit, OFF: 0~1.2VDC or Short circuit pin 2 and 3 OFF idle current: 5mA typ. GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage (60sec): 1600VDC Input/Output: 1600VDC Case/Input & Output: 1600VDC I/O Isolation Capacitance: 1500pF typ. I/O Isolation Resistance: 1000M Ohm 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice.= Switching Frequency: 330kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 560khrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+75°C (see Derating Curve) Maximum Case Temperature: 105°C Storage Temperature : -55°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Base Material: Non-conductive Black Plastic (UL94V-0 rated) Case Material: Nickel-coated Coppe PIN Material: 1.0mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 19.0g Dimmension DIP: 1.00“ x 1.00“ x 0.40“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 24V Models: 50VDC max. 48V Models: 100VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RV7-2403S20A1W 9-36 50 703 3.3 0 4500 88 10000 RV7-2405S20A1W 9-36 50 936 5 0 4000 89 5000 RV7-2412S20A1W 9-36 22 936 12 0 1670 89 850 RV7-2415S20A1W 9-36 22 936 15 0 1330 89 700 RV7-4803S20A1W 18-75 30 352 3.3 0 4500 88 10000 RV7-4805S20A1W 18-75 30 468 5 0 4000 89 5000 RV7-4812S20A1W 18-75 15 468 12 0 1670 89 850 RV7-4815S20A1W 18-75 15 468 15 0 1330 89 700 RV7-2412D20A1W 9-36 25 936 ±12 0 ±833 89 ±470 RV7-2415D20A1W 9-36 25 936 ±15 0 ±667 89 ±330 RV7-4812D20A1W 18-75 15 468 ±12 0 ±833 89 ±470 RV7-4815D20A1W 18-75 15 468 ±15 0 ±667 89 ±330 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. "Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 8. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 9. Input filter meets EN 55022 Class A without external components. 10. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RV7-2403S20A1W 9-36 50 703 3.3 0 4500 88 10000 RV7-2405S20A1W 9-36 50 936 5 0 4000 89 5000 RV7-2412S20A1W 9-36 22 936 12 0 1670 89 850 RV7-2415S20A1W 9-36 22 936 15 0 1330 89 700 RV7-4803S20A1W 18-75 30 352 3.3 0 4500 88 10000 RV7-4805S20A1W 18-75 30 468 5 0 4000 89 5000 RV7-4812S20A1W 18-75 15 468 12 0 1670 89 850 RV7-4815S20A1W 18-75 15 468 15 0 1330 89 700 RV7-2412D20A1W 9-36 25 936 ±12 0 ±833 89 ±470 RV7-2415D20A1W 9-36 25 936 ±15 0 ±667 89 ±330 RV7-4812D20A1W 18-75 15 468 ±12 0 ±833 89 ±470 RV7-4815D20A1W 18-75 15 468 ±15 0 ±667 89 ±330 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. "Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 8. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 9. Input filter meets EN 55022 Class A without external components. 10. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. DC/DC-Converter RV7-S20W/D20W 20W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RV7 - 24 03 S A120W

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Measured with a 1.0uF MLCC capacitor and a 10uF tantalum capacitor . The Scope measurement bandwidth is 0-20MHz. Copper Strip Lin Current +Vin +Vout +Vout Probe Cin DC/DC Converter Load Single DC/DC Converter 1uF 10uF Scope Resistive Load -Vin -Vout -Vout Output Ripple & Noise Reduction To reduce ripple and noise, it is recommended to use a 1uF ceramic disk capacitor and a 10uF electrolytic capacitor to at the output. + 10uF +Vin +Vout 10uF 1uF DC Power Source Cin Single DC/DC Converter Cout Load - -Vin -Vout CTRL Module ON / OFF Positive logic turns on the module during high logic and off during low logic. Ctrl module on/off can be controlled by an external switch between the ctrl terminal and -Vin terminal. The switch can be an open collector or open drain For positive logic if the ctrl feature is not used, please leave the ctrl pin floating. +Vin +Vout CTRL DC DC Converter Load -Vin -Vout Over Voltage Protection The module includes an internal output over voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over voltage set point, the module will activate the control loop of internal circuit to clamp the output voltage. Over Current Protection The module includes an internal over current protection circuit, which will endure current limiting for an unlimited duration during output over load condition. If the output current exceeds the OCP set point, the module will shut down automatically (hiccup). The module will try to restart after shut down. If the over load condition still exists, the module will shut down again. Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Measured with a 1.0uF MLCC capacitor and a 10uF tantalum capacitor . The Scope measurement bandwidth is 0-20MHz. Copper Strip Lin Current +Vin +Vout +Vout Probe Cin DC/DC Converter Load Single DC/DC Converter 1uF 10uF Scope Resistive Load -Vin -Vout -Vout Output Ripple & Noise Reduction To reduce ripple and noise, it is recommended to use a 1uF ceramic disk capacitor and a 10uF electrolytic capacitor to at the output. + 10uF +Vin +Vout 10uF 1uF DC Power Source Cin Single DC/DC Converter Cout Load - -Vin -Vout CTRL Module ON / OFF Positive logic turns on the module during high logic and off during low logic. Ctrl module on/off can be controlled by an external switch between the ctrl terminal and -Vin terminal. The switch can be an open collector or open drain For positive logic if the ctrl feature is not used, please leave the ctrl pin floating. +Vin +Vout CTRL DC DC Converter Load -Vin -Vout Over Voltage Protection The module includes an internal output over voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over voltage set point, the module will activate the control loop of internal circuit to clamp the output voltage. Over Current Protection The module includes an internal over current protection circuit, which will endure current limiting for an unlimited duration during output over load condition. If the output current exceeds the OCP set point, the module will shut down automatically (hiccup). The module will try to restart after shut down. If the over load condition still exists, the module will shut down again. DC/DC-Converter RV7-S20W/D20W 20W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Measured with a 1.0uF MLCC capacitor and a 10uF tantalum capacitor . The Scope measurement bandwidth is 0-20MHz. Copper Strip Lin Current +Vin +Vout +Vout Probe Cin DC/DC Converter Load Single DC/DC Converter 1uF 10uF Scope Resistive Load -Vin -Vout -Vout Output Ripple & Noise Reduction To reduce ripple and noise, it is recommended to use a 1uF ceramic disk capacitor and a 10uF electrolytic capacitor to at the output. + 10uF +Vin +Vout 10uF 1uF DC Power Source Cin Single DC/DC Converter Cout Load - -Vin -Vout CTRL Module ON / OFF Positive logic turns on the module during high logic and off during low logic. Ctrl module on/off can be controlled by an external switch between the ctrl terminal and -Vin terminal. The switch can be an open collector or open drain For positive logic if the ctrl feature is not used, please leave the ctrl pin floating. +Vin +Vout CTRL DC DC Converter Load -Vin -Vout Over Voltage Protection The module includes an internal output over voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over voltage set point, the module will activate the control loop of internal circuit to clamp the output voltage. Over Current Protection The module includes an internal over current protection circuit, which will endure current limiting for an unlimited duration during output over load condition. If the output current exceeds the OCP set point, the module will shut down automatically (hiccup). The module will try to restart after shut down. If the over load condition still exists, the module will shut down again.

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 DC/DC-Converter RV7-S20W/D20W 20W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS RV7-XXXXS20A1W RV7-XXXXS20A1W RV7-XXXXS20A1W The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28