RV7-2403S30A1W RSG | Alldatasheet

Document overview

  • PDF pages: 4

Technical content

1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RV7-S30W/D30W 30.0W 4:1 Regulated Single & Dual Output

  • 1” x 1” Package
  • Wide 4:1 Input Range
  • 1600VDC Isolation
  • Over Temperature Protection (case) 115°C, typ.
  • Continuous Short Circuit Protection
  • Over Voltage Protection
  • Over Load Protection
  • Efficiency up to 92%
  • Operating Temperature Range -40° ~ +85°C
  • Metal Case, Optional with Heat-sink
  • Soft Start
  • Remote on/off Control OUTPUT SPECIFICATION Voltage accuracy: ±1.0% Line regulation: Single &Dual ± 0.5% max. LOAD REGULATION: from 0% to 100% Load: ±0.5 - 1% max. Cross Regulation (Dual Output): ± 5% Over Voltage Protection (Zener diode clamp): Zener Diode Clamp Over Current Protection: 170%of Fl, typ.. Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 60-75mV pk-pk max. Temperature coefficient: ±0.02%/°C Capacitor load: See table Transient Recovery Time: 250us,typ. Transient Response: (Deviation) ±3-5% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 30ms,typ. Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 30mA pk-pk typ. Remote On/Off (positive logic): On: 3.0~12VDC or open circuit, OFF: 0~1.2VDC or Short circuit pin 2 and 3, OFF idle current: 2mA typ. OFF idle current: See table typ. GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage (60sec): 1600VDC, Input/Output, Case/Input & Output I/O Isolation Capacitance: 2000pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 270kHz-330kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 370KHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+100°C (see Derating Curve) Maximum Case Temperature: 105°C Storage Temperature : -55°C ~+125°C Cooling : Nature Convection (with Heat-sink) PHYSICAL SPECIFICATIONS: Case Material: Copper Black Base Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: 1.0mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 19.0g Dimmension DIP: 1.0“ x 1.0“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 24V Models: -0.7~50VDC 48V Models: -0.7~100VDC Soldering Temperature: 260°C max. EMC SPECIFICATIONS (2) Radiated-/Conducted Emissions: IEC 61000-4-2 Perf.Criteria A ESD: IEC 61000-4-3 Perf.Criteria A RS: IEC 61000-4-4 Perf.Criteria A EFT: IEC 61000-4-5 Perf.Criteria A SURGE: IEC 61000-4-6 Perf.Criteria A CS: IEC 61000-4-8 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS DC/DC-Converter 30.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01

6.0W Regulated Single & Dual Output DC/DC-Converter 30.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 Derating Curve 100% 75% 50% S.O.A. 25% 55 85 -40 -20 0 20 40 60 80 100 120 AMBIENT TEMPERATURE(° C) OUTPUTPOWER MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL (%, typ.) Capacitor Load @FL (µF, max.) No-Load (mA, max.) Full Load (mA, typ.) Min. load (mA) Full load (mA) RV7-2403S30A1W 9-36, 24V Nominal 10 1093.75 3.3 0 7000 88 10000 RV7-2405S30A1W 9-36, 24V Nominal 10 1404.49 5 0 6000 89 7200 RV7-2412S30A1W 9-36, 24V Nominal 10 1404.49 12 0 2500 89 1200 RV7-2415S30A1W 9-36, 24V Nominal 10 1373.62 15 0 2000 91 1000 RV7-4803S30A1W 18-75, 48V Nominal 8 540.73 3.3 0 7000 89 10000 RV7-4805S30A1W 18-75, 48V Nominal 8 694.44 5 0 6000 90 7200 RV7-4812S30A1W 18-75, 48V Nominal 8 694.44 12 0 2500 90 1200 RV7-4815S30A1W 18-75, 48V Nominal 8 679.34 15 0 2000 92 1000 RV7-2412D30A1W 9-36, 24V Nominal 10 1404.49 ±12 0 ±1250 89 ±750 RV7-2415D30A1W 9-36, 24V Nominal 10 1373.62 ±15 0 ±1000 91 ±500 RV7-4812D30A1W 18-75, 48V Nominal 8 694.44 ±12 0 ±1250 90 ±750 RV7-4815D30A1W 18-75, 48V Nominal 8 686.81 ±15 0 ±1000 91 ±500 The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : sales@motien.com.tw wit hout heat sink with heat sink 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Testedby minimal Vin and constant resistive load. 3. Testedby normal Vin and 25% load step change ( 75%-50%-25% of Io ). 4. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF, ESR<1.0© at100KHz). 5. The remote on/off control pin is referenced to-Vin(pin2). 6. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 7. "Nature Convection" is usually about 30-65 LFM but is not equal to still air (0LFM). 8. Input filter components are used to help meet conductedemissions, Which application refer to the EMI Filter of design & feature configuration. 9. An external filter capacitor is required if the module has to meet EN61000-4-4,EN61000-4-5. The RV7-24XXXX30 recommended an aluminum electrolytic capacitor ( Nippon chemi-con KY series, 330uF/100V) and a TVS (SMDJ58A,58V,3000Watt peak pulse power) to connect in parallel. The RV7-48XXXX30 recommended an aluminum electrolytic capacitor ( Nippon chemi-con KY series, 330uF/100V) and a TVS (SMDJ120A,120V,3000Watt peak pulse power) to connect in parallel. RV7 - XX XX X XX Power (W) Input Type A X W X Code internal Isolation (kVDC) W = 4:1 input Range K = Option mit Kühlkörper

6.0W Regulated Single & Dual Output DC/DC-Converter 30.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test To reduce ripple and noise, it is recommended to use a 1uF ceramic disk capacitor and a 10uF ceramic disk capacitor to at the output. Copper Strip +Vin +Vout +Vout 1uF 10uF Lin Current Probe Cin DC/DC Converter -Vin -Vout Load DC/DC Converter COM -Vout Cout 1uF Cout Cout Scope Resistive Load 10uF Cout Scope Over Voltage Protection The module includes an internal output over voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over voltage set point, the module will activate the control loop of internal circuit to clamp the output voltage. Over Temperature Protection The over temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over temperature threshold the module will shut down. The module will try to restart after shut down, If the over temperature condition still exists during restart, the module will shut down again. This restart trial will continue until the temperature is within specification. EMI Filter Input filter components (C1,L) are used to help meet conducted emissions . These components should be mounted as close as possible to the module; and all leads should be minimized Over Current Protection The module includes an internal over current protection circuit, which will endure current limiting for an unlimited duration during output over load condition. If the output current exceeds the OCP set point, the module will shut down automatically (hiccup). The module will try to restart after shut down. If the over load condition still exists, the module will shut down again. CTRL Module ON / OFF Positive logic turns on the module during high logic and off during low logic. Ctrl module on/off can be controlled by an external switch between the ctrl terminal and -Vin terminal. The switch can be an open collector or open drain For positive logic if the ctrl feature is not used, please leave the ctrl pin floating. +Vin +Vout to decrease radiated noise. +VinL +Vout CTRL DC DC Converter -Vin -Vout Load DC/DC C1 Converter -Vin -Vout Load RV7-24XXXXX RV7-48XXXXX 1206, 3.3uF/100V 1206, 1uF/100V L 0.82uH 2.2uH The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : sales@motien.com.tw TEST CONFIGURATIONS DESIGN & FEATURE CONFIGURATIONS

6.0W Regulated Single & Dual Output DC/DC-Converter 30.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 10.16 Top View 2.54 (0.10) 10.16 (0.40) (0.40) 2.54 (0.10) 4 6 -Vo TRIM +Vo RSG RV7-2405S30A1W Vin : 9-36Vdc Vout : 5Vdc Iout : 6000mA XXXX CTRL - Vi + 20.32 (0.80) Bottom View 15.24 (0.60) 1 2 3 25.4 (1.0) 2.54 (0.10) 5.08 (0.20) 7.62 (0.30) 2.54 (0.10) All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 4. Stand-off tolerance: ±0.1 ( ±0.004 ) 4 5 Bottom View 1 2 0.5 (0.02) 10.4 (0.41) DIA 1.00 (0.04) 6.00 (0.24) With Heat-sink 2.54 15.24 2.54 (0.10) 0.5 25.4 16.8 10.16 (0.40) 7.62 (0.30) 5.08 (0.20) 25.4 (1.00) DIA 1.00 10.16 (0.40) (0.04) 2.54 (0.10) 20.32 (0.80) 2.54 (0.10) 16.8 (0.66) 6.00 (0.24) Order code: Material: Finish: Weight: Note: RV7-XXXXX30SK(contain: heat-sink, thermal pad) Aluminum Anodic treatment (black) 2.9 g (0.1oz) (without converter) 1. Converters will be supplied with heat -sinks already mounted. Please contact RSG for quotation. MOTIEN ISO 9001 . ISO 14001 . IECQ QC080000 DRAWING: APPROVE No. 9, Keji 2nd Rd., Tainan Technology Industrial Park, Tainan City 70955, Taiwan Te l : 886-6-384 2366 (Rep.) Fax: 886-6-384 2399 Last Update : Mar.24.2016 EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method as below. (single output models only) Rtrim-up Rtrim-down 5 4 6 5 DIA 1.00 (0.04) 25.4 (1.00) RSG RV7-2412D30SK1316 25.4 (1.0) Vin : 9-36Vdc Vout : ±12Vdc Iout : ±1250mA PIN CONNECTIONS PIN NUMBER SINGLE DUAL 1 +Vin +Vin 2 -Vin -Vin

3 CTRL CTRL

5 Trim Com

The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28