RV7-1203D15A1

RV7-1203S15A1 RSG | Alldatasheet

Document overview

• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RV7-S15/D15 15W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 1“ x 1“ Package, Full SMD Technologie
• Wide 2:1 Input Range
• Soft Start
• No Minimum Load Required
• Adjustable Output Voltage
• Over Current Protection
• Over Voltage Protection
• 1600VDC Isolation
• Continuous Short Circuit Protection
• Efficiency up to 89%
• Operating Temperature Range -40° ~ +85°C
• Remote On/Off Control (CTRL) OUTPUT SPECIFICATION Voltage accuracy: ±1% Output Voltage Adjustability (Trim): Singel Output: ±10% max. Line regulation: Single &Dual ±0.2% max. LOAD REGULATION: Singel: ±0.5% max. Dual: ±1%,max.(balanced load) Cross Regulation (Dual Output): ±5% Over Voltage Protection (Zener diode clamp): See table Over Current Protection: 150% of Fl, typ. Short Circuit Protection : Indefinite (hiccup) (Automatic Recovery) Ripple noise (20Mhz bandwidth): 100mV pk-pk max. Temperature coefficient: ±0.02% °C Capacitor load: See table Transient Recovery Time: 250us, typ. Transient Response: ( Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 20ms,typ. No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 20mA pk-pk typ. Remote On/Off (positive logic): On: 3.0~12VDC or open circuit, OFF: 0~1.2VDC or Short circuit pin 2 and 3 OFF idle current: 5mA typ. GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage (60sec): 1600VDC Input/Output 1600VDC Case Input & Output: 1600VDC I/O Isolation Capacitance: 1200pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 375kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 560khrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 105°C Storage Temperature : -55°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Base Material: Non-conductive Black Plastic (UL94V-0 rated) Case Material: Nickel-coated Copper PIN Material: 1.0mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 18.0g Dimmension DIP: 1.00“ x 1.00“ x 0.40“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 12V Models: 36VDC max. 24V Models: 50VDC max. 48V Models: 100VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A see EMI Filter note ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ±5 0 ±1500 85 ±470 RV7-1212D15A1 9-18 20 1420 ±12 0 ±625 89 ±220 RV7-1215D15A1 9-18 20 1437 ±15 0 ±500 89 ±100 RV7-2405D15A1 18-36 15 744 ±5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ±15 0 ±500 89 ±100 RV7-4805D15A1 36-75 10 377 ±5 0 ±1500 84 ±470 RV7-4812D15A1 36-75 10 363 ±12 0 ±625 87 ±220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de C1 L C2 RV7-12XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-24XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-48XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ±5 0 ±1500 85 ±470 RV7-1212D15A1 9-18 20 1420 ±12 0 ±625 89 ±220 RV7-1215D15A1 9-18 20 1437 ±15 0 ±500 89 ±100 RV7-2405D15A1 18-36 15 744 ±5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ±15 0 ±500 89 ±100 RV7-4805D15A1 36-75 10 377 ±5 0 ±1500 84 ±470 RV7-4812D15A1 36-75 10 363 ±12 0 ±625 87 ±220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de C1 L C2 RV7-12XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-24XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-48XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ±5 0 ±1500 85 ±470 RV7-1212D15A1 9-18 20 1420 ±12 0 ±625 89 ±220 RV7-1215D15A1 9-18 20 1437 ±15 0 ±500 89 ±100 RV7-2405D15A1 18-36 15 744 ±5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ±15 0 ±500 89 ±100 RV7-4805D15A1 36-75 10 377 ±5 0 ±1500 84 ±470 RV7-4812D15A1 36-75 10 363 ±12 0 ±625 87 ±220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de C1 L C2 RV7-12XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-24XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-48XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V DC/DC-Converter RV7-S15/D15 15W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! +Vout +Vin DC/DC Converter -Vin -Vout NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1.0uF ceramic capacitor and 10uF tantalum capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uHand a source capacitor Cin (47uF, ESR<1.0© at 100KHz). 6. The remote on/off control pin is referenced to -Vin(pin2). 7. Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 9. Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM). 10 .Exceeding the absolute ratings of the unit could cause damage. It is not for continuous operating L Load C1 C2 MODEL SELECTION GUIDE NODEL NUNBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Nin. load (mA) Full load (mA) RV7-1203S15A1 9-18 20 1310 3.3 0 4000 85 1000 RV7-1205S15A1 9-18 20 1471 5 0 3000 86 1000 RV7-1212S15A1 9-18 20 1494 12 0 1300 88 330 RV7-1215S15A1 9-18 20 1420 15 0 1000 89 220 RV7-2403S15A1 18-36 15 647 3.3 0 4000 86 1000 RV7-2405S15A1 18-36 15 727 5 0 3000 87 1000 RV7-2412S15A1 18-36 15 747 12 0 1300 88 330 RV7-2415S15A1 18-36 15 710 15 0 1000 89 220 RV7-4803S15A1 36-75 10 327 3.3 0 4000 85 1000 RV7-4805S15A1 36-75 10 368 5 0 3000 86 1000 RV7-4812S15A1 36-75 10 374 12 0 1300 88 330 RV7-4815S15A1 36-75 10 359 15 0 1000 88 220 RV7-1205D15A1 9-18 20 1488 ±5 0 ±1500 85 ±470 RV7-1212D15A1 9-18 20 1420 ±12 0 ±625 89 ±220 RV7-1215D15A1 9-18 20 1437 ±15 0 ±500 89 ±100 RV7-2405D15A1 18-36 15 744 ±5 0 ±1500 85 ±470 RV7-2412D15A1 18-36 15 718 ±12 0 ±625 88 ±220 RV7-2415D15A1 18-36 15 710 ±15 0 ±500 89 ±100 RV7-4805D15A1 36-75 10 377 ±5 0 ±1500 84 ±470 RV7-4812D15A1 36-75 10 363 ±12 0 ±625 87 ±220 RV7-4815D15A1 36-75 10 359 ±15 0 ±500 88 ±100 NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de C1 L C2 RV7-12XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-24XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7-48XXX15A1 1210, 2.2uF/100V 12uH 1210, 2.2uF/100V RV7 - XX XX S/D XX Power (W) Input Type A X Code internal Isolation (kVDC)

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 RV7 -4812D 15A1 EFFICIENCY VS OUT PUT CURRENT 95.00 Lo Line 90.00 85.00

80.00 Nominal

75.00 70.00 65.00 20% 40% 60% Load 80% 100% RV7 -2412D 15A1 EFFICIENCY VS OUT PUT CURRENT 95.00 Nominal 90.00 Lo Line85.00 Hi Line 80.00 75.00 70.00 20% 40% 60% Load 80% 100% RV7 -1212D 15A1 EFFICIENCY VS OUT PUT CURRENT 95.00 Lo Line Nominal 90.00 85.00 Hi Line 80.00 75.00 70.00 20% 40% 60% Load 80% 100% RV7-1203S15 A1 EFFICIENCY VS OUT PUT CURRENT 95.00 Hi Line 90.00 85.00 Nominal80.00 Lo Line 75.00 70.00 65.00 20% 40% 60% Load 80% 100% RV-2403S15 A1 EFFICIENCY VS OUT PUT CURRENT 95.00

90.00 Lo Line

85.00 80.00 Nominal 75.00 Hi Line 70.00 65.00 20% 40% 60% Load 80% 100% RV7-4803S15 A1 EFFICIENCY VS OUT PUT CURRENT 90.00 85.00 80.00 75.00 70.00 65.00 60.00 55.00 Lo Line Nominal Hi Line 20% 40% 60% Load 80% 100% Efficiency(%) Efficiency(%) Efficiency(%) Efficiency(%) Efficiency(%) Efficiency(%) DC/DC-Converter RV7-S15/D15 15W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RV7-XXXXS15A1 RV7-XXXXS15A1 RV7-XXXXS15A1 DC/DC-Converter RV7-S15/D15 15W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28