RS8-0505R10A1

RS8-0505R10A1 RSG | Alldatasheet

Document overview

• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 DC/DC-Converter RS8-R10/RD10 1.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 6 Pin SIL Package
• Wide 2:1 Input Range
• 1500VDC Isolation
• Continuous Short Circuit Protection
• no minimum Load required
• Efficiency up to 81%
• Operating Temperature Range -40° ~ +85°C
• Non Conductive Black Plastic Case OUTPUT SPECIFICATION Voltage accuracy: ±2% Maximum Output Current: See table Line regulation: ± 0.2% max. LOAD REGULATION: 0% - 100% (Single/Dual Outp.): ±1% max./±2% max. 5% - 100% (Dual Outp.): ±1% max. Cross Regulation (Dual Output): ± 5% Short Circuit Protection : Continuous (Automatic Recovery ) Ripple noise (20Mhz bandwidth): 50mV pk-pk max. Temperature coefficient: ±0.02% °C Capacitor load: See table Transient Recovery Time: 500us, typ. Transient Response: ( Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1500VDC I/O Isolation Capacitance: 70pF typ. I/O Isolation Resistance: 1000M Ohm, min Switching Frequency: 150 - 550kHz Humidity: 95% rel H Reliability Calculated MTBF : > 2.8MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC EN 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 105°C Storage Temperature : -55°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material SIP Case: C5191T-H Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 3.0g, Dimmension SIP: 0.67 x 0.30 x 0.43“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 5 V Models: 15VDC max. 12V Models: 25VDC max. 24V Models: 50VDC max. 48V Models: 100VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believ ed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL (%) Capacitive Load (uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RS8-0505R10A1 4.5-9 35 263 5 0 200 76 1680 RS8-0512R10A1 4.5-9 35 253 12 0 83 79 820 RS8-0515R10A1 4.5-9 35 250 15 0 67 80 680 RS8-0524R10A1 4.5-9 35 250 24 0 42 80 470 RS8-1205R10A1 9-18 20 107 5 0 200 78 1680 RS8-1212R10A1 9-18 20 105 12 0 83 80 820 RS8-1215R10A1 9-18 20 103 15 0 67 81 680 RS8-1224R10A1 9-18 20 105 24 0 42 80 470 RS8-2405R10A1 18-36 10 54 5 0 200 78 1680 RS8-2412R10A1 18-36 10 52 12 0 83 80 820 RS8-2415R10A1 18-36 10 52 15 0 67 80 680 RS8-2424R10A1 18-36 10 52 24 0 42 81 470 RS8-4805R10A1 36-75 7 28 5 0 200 76 1680 RS8-4812R10A1 36-75 7 27 12 0 83 78 820 RS8-4815R10A1 36-75 7 27 15 0 67 78 680 RS8-4824R10A1 36-75 7 27 24 0 42 77 470 RS8-0512RD10A1 4.5-9 35 259 ±12 0 ±42 77 ±470 RS8-0515RD10A1 4.5-9 35 254 ±15 0 ±33 79 ±330 RS8-1212RD10A1 9-18 20 106 ±12 0 ±42 79 ±470 RS8-1215RD10A1 9-18 20 105 ±15 0 ±33 80 ±330 RS8-2412RD10A1 18-36 10 52 ±12 0 ±42 80 ±470 RS8-2415RD10A1 18-36 10 53 ±15 0 ±33 79 ±330 RS8-4812RD10A1 36-75 7 27 ±12 0 ±42 77 ±470 RS8-4815RD10A1 36-75 7 27 ±15 0 ±33 77 ±330 The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Ripple/Noise measured with a 1uF ceramic capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH. 6. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 7.Input filter components are be required to help meet conducted emission class A, which application refer to The EMI Filter of Design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: 5Vin models : Nippon - chemi - con KY series, 330uF/100V. Other models : Nippon - chemi - con KY series, 220uF/100V. DC/DC-Converter RS8-R10/RD10 1.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RS8 - XX XX X XX Power (W) Input Type A X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL (%) Capacitive Load (uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RS8-0505R10A1 4.5-9 35 263 5 0 200 76 1680 RS8-0512R10A1 4.5-9 35 253 12 0 83 79 820 RS8-0515R10A1 4.5-9 35 250 15 0 67 80 680 RS8-0524R10A1 4.5-9 35 250 24 0 42 80 470 RS8-1205R10A1 9-18 20 107 5 0 200 78 1680 RS8-1212R10A1 9-18 20 105 12 0 83 80 820 RS8-1215R10A1 9-18 20 103 15 0 67 81 680 RS8-1224R10A1 9-18 20 105 24 0 42 80 470 RS8-2405R10A1 18-36 10 54 5 0 200 78 1680 RS8-2412R10A1 18-36 10 52 12 0 83 80 820 RS8-2415R10A1 18-36 10 52 15 0 67 80 680 RS8-2424R10A1 18-36 10 52 24 0 42 81 470 RS8-4805R10A1 36-75 7 28 5 0 200 76 1680 RS8-4812R10A1 36-75 7 27 12 0 83 78 820 RS8-4815R10A1 36-75 7 27 15 0 67 78 680 RS8-4824R10A1 36-75 7 27 24 0 42 77 470 RS8-0512RD10A1 4.5-9 35 259 ±12 0 ±42 77 ±470 RS8-0515RD10A1 4.5-9 35 254 ±15 0 ±33 79 ±330 RS8-1212RD10A1 9-18 20 106 ±12 0 ±42 79 ±470 RS8-1215RD10A1 9-18 20 105 ±15 0 ±33 80 ±330 RS8-2412RD10A1 18-36 10 52 ±12 0 ±42 80 ±470 RS8-2415RD10A1 18-36 10 53 ±15 0 ±33 79 ±330 RS8-4812RD10A1 36-75 7 27 ±12 0 ±42 77 ±470 RS8-4815RD10A1 36-75 7 27 ±15 0 ±33 77 ±330 The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg-electronic.de NOTE 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Ripple/Noise measured with a 1uF ceramic capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Measured Input reflected ripple current with a simulated source inductance of 12uH. 6. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 7.Input filter components are be required to help meet conducted emission class A, which application refer to The EMI Filter of Design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: 5Vin models : Nippon - chemi - con KY series, 330uF/100V. Other models : Nippon - chemi - con KY series, 220uF/100V.

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Input Reflected Ripple Current Test Step Input reflected ripple current is measured through +Vout a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin +Vin DC/DC Converter Load -Vin -Vout Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF)measurement. The Scope measurement bandwidth is 20MHz. +Vout Single DC/DC Copper Strip 1uF Scope Resistive Dual DC/DC +Vout Copper Strip 1uF Cout Scope Resistive Converter -Vout Cout Load COM Converter -Vout 1uF Cout Scope Load EMI Filter Input filter components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +VinL +Vout DC/DC C1 Converter Load -Vin -Vout +Vin L +Vout Load DC/DC ComC1 Converter Load -Vin -Vout C1 C2 L RS8-05XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 4.7uH RS8-12XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 4.7uH RS8-24XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 18uH RS8-48XXR/RD10A1 MLCC 4,7uF/100V MLCC 220uF/3KV 18uH DC/DC-Converter RS8-R10/RD10 1.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! Input Reflected Ripple Current Test Step Input reflected ripple current is measured through +Vout a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin +Vin DC/DC Converter Load -Vin -Vout Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF)measurement. The Scope measurement bandwidth is 20MHz. +Vout Single DC/DC Copper Strip 1uF Scope Resistive Dual DC/DC +Vout Copper Strip 1uF Cout Scope Resistive Converter -Vout Cout Load COM Converter -Vout 1uF Cout Scope Load EMI Filter Input filter components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +VinL +Vout DC/DC C1 Converter Load -Vin -Vout +Vin L +Vout Load DC/DC ComC1 Converter Load -Vin -Vout C1 C2 L RS8-05XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 4.7uH RS8-12XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 4.7uH RS8-24XXR/RD10A1 MLCC 4,7uF/50V MLCC 220uF/3KV 18uH RS8-48XXR/RD10A1 MLCC 4,7uF/100V MLCC 220uF/3KV 18uH

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RS8-XXXXR10A1 RS8-XXXXR10A1 RS8-XXXXR10A1 DC/DC-Converter RS8-R10/RD10 1.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28