RS5-1203R20A1W RSG | Alldatasheet

Document overview

  • PDF pages: 3

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (3) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS5-R20W/RD20W 2.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

  • 8 Pin SIL Package
  • Wide 4:1 Input Range
  • 1600VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 82%
  • Operating Temperature Range -40° ~ +85°C
  • Non Conductive Black Plastic Case
  • Remote on/off Control(Optional) ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non conductive black plastic PIN Material SIP Case: C519R-H Solder -coated Potting Material: Silicon (UL94V-0 rated) Weight Case- Sip: 4.8g, typ. Dimmension SIP: 0.86 x 0.36 x 0.44“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/max.

12 V Models: 25VDC max

24 V Models: 50VDC max. 48 V Models: 100VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A OUTPUT SPECIFICATION Voltage accuracy: ±1% Maximum Output Current: See table Line regulation: ± 0.2% max. LOAD REGULATION: Single (from 0% to 100% Load) ±1% max. Dual (from 10% to 100% Load) ±1% max. Cross Regulation (Dual Output): ± 5% Short Circuit Protection : Indefinite (Automatic Recovery ) Ripple noise (20Mhz bandwidth): 30mV pk-pk max. Temperature coefficient: ±0.02%<>°C Capacitor load: See table Transient Recovery Time: 250us, typ. Transient Response: ( Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 30ms, typ. Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1600VDC I/O Isolation Capacitance: 200pF max. I/O Isolation Resistance: 1000M Ohm, min Switching Frequency: 100kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.7MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 Remote on Controll: on: open or high impedance Remote off Controll: 2-4mA Input current (via 1K) Off stand by current (Nominal Vin): 2.5mA max. RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (3) STAND Juni 2016 Rev 01 DC/DC-Converter RS5-R20W/RD20W 2.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RS5 - XX XX XX XX Power (W) Input Type A X W Code internal Isolation (kVDC) W = 4:1 input Range MODEL SELECTION GUIDE NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg -electronic.de 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1uF ceramic capacitor. 3. Test by minimal Vin and constant resistive load. 4. Test by normal Vin and 100%-25% load,25% Ioad step change. 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 6. Exceeding the absolute ratings of the unit could cause damage. It's not allowed for continuous operating ratings. 7. Input filter components are be required to help meet conducted emission classA, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load RS5-1203R20A1W 4.5-18 40 196 3.3 0 500 70 1000uF RS5-1205R20A1W 4.5-18 40 225 5 0 400 74 1000uF RS5-1212R20A1W 4.5-18 40 213 12 0 167 78 220uF RS5-1215R20A1W 4.5-18 40 213 15 0 133 78 100uF RS5-1205SRD20A1W 4.5-18 30 219 ±5 0 ±200 77 ±470uF RS5-1212SRD20A1W 4.5-18 30 213 ±12 0 ±83 78 ±100uF RS5-1215SRD20A1W 4.5-18 40 216 ±15 0 ±66 77 ±47uF RS5-2403R20A1W 9-36 25 96 3.3 0 500 71 1000uF RS5-2405R20A1W 9-36 20 106 5 0 400 78 1000uF RS5-2412R20A1W 9-36 30 105 12 0 167 79 220uF RS5-2415R20A1W 9-36 30 105 15 0 133 79 100uF RS5-2405SRD20A1W 9-36 30 111 ±5 0 ±200 75 ±470uF RS5-2412SRD20A1W 9-36 30 108 ±12 0 ±83 77 ±100uF RS5-2415SRD20A1W 9-36 30 106 ±15 0 ±66 78 ±47uF RS5-4803R20A1W 18-75 10 47 3.3 0 500 72 1000uF RS5-4805R20A1W 18-75 15 55 5 0 400 75 1000uF RS5-4812R20A1W 18-75 15 55 12 0 167 75 220uF RS5-4815R20A1W 18-75 15 54 15 0 133 76 100uF RS5-4805SRD20A1W 18-75 15 56 ±5 0 ±200 74 ±470uF RS5-4812SRD20A1W 18-75 15 56 ±12 0 ±83 74 ±100uF RS5-4815SRD20A1W 18-75 15 55 ±15 0 ±66 75 ±47uF MODEL SELECTION GUIDE NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg -electronic.de 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with a 1uF ceramic capacitor. 3. Test by minimal Vin and constant resistive load. 4. Test by normal Vin and 100%-25% load,25% Ioad step change. 5. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 6. Exceeding the absolute ratings of the unit could cause damage. It's not allowed for continuous operating ratings. 7. Input filter components are be required to help meet conducted emission classA, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load RS5-1203R20A1W 4.5-18 40 196 3.3 0 500 70 1000uF RS5-1205R20A1W 4.5-18 40 225 5 0 400 74 1000uF RS5-1212R20A1W 4.5-18 40 213 12 0 167 78 220uF RS5-1215R20A1W 4.5-18 40 213 15 0 133 78 100uF RS5-1205SRD20A1W 4.5-18 30 219 ±5 0 ±200 77 ±470uF RS5-1212SRD20A1W 4.5-18 30 213 ±12 0 ±83 78 ±100uF RS5-1215SRD20A1W 4.5-18 40 216 ±15 0 ±66 77 ±47uF RS5-2403R20A1W 9-36 25 96 3.3 0 500 71 1000uF RS5-2405R20A1W 9-36 20 106 5 0 400 78 1000uF RS5-2412R20A1W 9-36 30 105 12 0 167 79 220uF RS5-2415R20A1W 9-36 30 105 15 0 133 79 100uF RS5-2405SRD20A1W 9-36 30 111 ±5 0 ±200 75 ±470uF RS5-2412SRD20A1W 9-36 30 108 ±12 0 ±83 77 ±100uF RS5-2415SRD20A1W 9-36 30 106 ±15 0 ±66 78 ±47uF RS5-4803R20A1W 18-75 10 47 3.3 0 500 72 1000uF RS5-4805R20A1W 18-75 15 55 5 0 400 75 1000uF RS5-4812R20A1W 18-75 15 55 12 0 167 75 220uF RS5-4815R20A1W 18-75 15 54 15 0 133 76 100uF RS5-4805SRD20A1W 18-75 15 56 ±5 0 ±200 74 ±470uF RS5-4812SRD20A1W 18-75 15 56 ±12 0 ±83 74 ±100uF RS5-4815SRD20A1W 18-75 15 55 ±15 0 ±66 75 ±47uF RS5 - XX XX XX XX Power (W) Input Type A X W Code internal Isolation (kVDC) W = 4:1 input Range

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (3) STAND Juni 2016 Rev 01 EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitorCout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. +Vout Single DC/DC Converter Copper Strip 1uF Cout Scope Resistive Load -Vout +VinL +Vout EMI Filter Input filter components (C1, L) are used to help DC/DC C1 Converter Load meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. -Vin -Vout RS5-1203R20A1W RS5-4815RD20A1W +Vout +VinLin Current Probe Cin DC/DC Converter Load -Vin -Vout Efficiency(%) Efficiency(%) C1 L RS5-12XXR/RD20A1W 1210 10uF/35V 2.5uH RS5-24XXR/RD20A1W 1210 2.2uF/100V 10uH RS5-48XXR/RD20A1W 1210 2.2uF/100V 18uH EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitorCout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. +Vout Single DC/DC Converter Copper Strip 1uF Cout Scope Resistive Load -Vout +VinL +Vout EMI Filter Input filter components (C1, L) are used to help DC/DC C1 Converter Load meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. -Vin -Vout RS5-1203R20A1W RS5-4815RD20A1W +Vout +VinLin Current Probe Cin DC/DC Converter Load -Vin -Vout Efficiency(%) Efficiency(%) C1 L RS5-12XXR/RD20A1W 1210 10uF/35V 2.5uH RS5-24XXR/RD20A1W 1210 2.2uF/100V 10uH RS5-48XXR/RD20A1W 1210 2.2uF/100V 18uH EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitorCout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. +Vout Single DC/DC Converter Copper Strip 1uF Cout Scope Resistive Load -Vout +VinL +Vout EMI Filter Input filter components (C1, L) are used to help DC/DC C1 Converter Load meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. -Vin -Vout RS5-1203R20A1W RS5-4815RD20A1W +Vout +VinLin Current Probe Cin DC/DC Converter Load -Vin -Vout Efficiency(%) Efficiency(%) C1 L RS5-12XXR/RD20A1W 1210 10uF/35V 2.5uH RS5-24XXR/RD20A1W 1210 2.2uF/100V 10uH RS5-48XXR/RD20A1W 1210 2.2uF/100V 18uH EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 10% 20% 40% 60% 80% 100% LOAD Lo Line/Iin Nominal/Iin Hi Line/Iin Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitorCout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. +Vout Single DC/DC Converter Copper Strip 1uF Cout Scope Resistive Load -Vout +VinL +Vout EMI Filter Input filter components (C1, L) are used to help DC/DC C1 Converter Load meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. -Vin -Vout RS5-1203R20A1W RS5-4815RD20A1W +Vout +VinLin Current Probe Cin DC/DC Converter Load -Vin -Vout Efficiency(%) Efficiency(%) C1 L RS5-12XXR/RD20A1W 1210 10uF/35V 2.5uH RS5-24XXR/RD20A1W 1210 2.2uF/100V 10uH RS5-48XXR/RD20A1W 1210 2.2uF/100V 18uH DC/DC-Converter RS5-R20W/RD20W 2.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RS5-XXXXR20A1W MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28