RS2-0505D10AXM RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS2-S10M/D10M 1.0W semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

FEATURES

  • 7 Pin SIL Package
  • 1000VDC Isolation
  • Up to 3000VDC Isolation
  • Low Ripple and Noise
  • Efficiency up to 89%
  • Operating Temperature Range: -40° ~ +85°C
  • Non Conductive Black Plastic Case
  • EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: per 1%Vin Change: ±1.2% LOAD REGULATION: from 10% to 100% Load: see table Ripple & Noise: 50mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 20-50mA pk-pk by 5V-48V GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 70kHz Humidity: 95% rel H Reliability Calculated MTBF : >2.0MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: C5191R-H Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 2.4 ~ 2.8g Dimmension SIP: 0.76 x 0.24 (28“) x 0.39“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 9VDC max

12V Models: 18VDC max 15V Models: 20VDC max 24V Models: 30VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class B ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 DC/DC-Converter RS2-S10M/D10M 1.0W semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MODEL SELECTION GUIDE MODEL NUMBER INPUT VoltageRange (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUTCurrent Full load (mA) LOAD Regulation EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) RS2-0505D10AXM 5 20 230 ±5 ±100 6 84 ±100 RS2-0509D10AXM 5 30 230 ±9 ±55.55 5.5 86 ±100 RS2-0512D10AXM 5 20 228 ±12 ±41.67 5.5 87 ±47 RS2-0515D10AXM 5 20 228 ±15 ±33.33 5 87 ±47 RS2-1205D10AXM 12 15 98 ±5 ±100 4 85 ±100 RS2-1209D10AXM 12 15 95 ±9 ±55.55 3.5 86 ±100 RS2-1212D10AXM 12 15 94 ±12 ±41.67 3.5 87 ±47 RS2-1215D10AXM 12 15 94 ±15 ±33.33 3.5 87 ±47 RS2-1505D10AXM 15 10 78 ±5 ±100 3.5 85 ±100 RS2-1509D10AXM 15 10 76 ±9 ±55.55 2.5 87 ±100 RS2-1512D10AXM 15 10 76 ±12 ±41.67 2.5 87 ±47 RS2-1515D10AXM 15 10 75 ±15 ±33.33 2.5 88 ±47 RS2-2405D10AXM 24 7 51 ±5 ±100 3.5 82 ±100 RS2-2409D10AXM 24 7 49 ±9 ±55.55 2.5 85 ±100 RS2-2412D10AXM 24 7 48 ±12 ±41.67 2.5 87 ±47 RS2-2415D10AXM 24 7 48 ±15 ±33.33 2.5 87 ±47 RS2-4805D10AXM 48 5 27 ±5 ±100 3 77 ±100 RS2-4809D10AXM 48 5 26 ±9 ±55.55 3 81 ±100 RS2-4812D10AXM 48 5 26 ±12 ±41.67 3 82 ±47 RS2-4815D10AXM 48 5 26 ±15 ±33.33 2 81 ±47 RS2-0505S10AXM 5 20 250 5 200 6 83 220 RS2-0509S10AXM 5 20 230 9 111.1 5.5 86 220 RS2-0512S10AXM 5 20 230 12 83.3 5.5 87 100 RS2-0515S10AXM 5 20 230 15 66.7 5 87 100 RS2-1205S10AXM 12 15 98 5 200 4 84 220 RS2-1209S10AXM 12 15 96 9 111.1 3.5 86 220 RS2-1212S10AXM 12 15 95 12 83.3 3.5 88 100 RS2-1215S10AXM 12 15 95 15 66.7 3 88 100 RS2-1505S10AXM 15 10 79 5 200 4 84 220 RS2-1509S10AXM 15 10 77 9 111.1 3.5 86 220 RS2-1512S10AXM 15 10 76 12 83.3 3.5 87 100 RS2-1515S10AXM 15 10 76 15 66.7 3 89 100 RS2-2405S10AXM 24 7 51 5 200 4 81 220 RS2-2409S10AXM 24 7 50 9 111.1 3.5 84 220 RS2-2412S10AXM 24 7 49 12 83.3 3.5 85 100 RS2-2415S10AXM 24 7 49 15 66.7 2.5 86 100 RS2-4805S10AXM 48 5 27 5 200 4 78 220 RS2-4809S10AXM 48 5 26 9 111.1 3.5 80 220 RS2-4812S10AXM 48 5 26 12 83.3 3 81 100 RS2-4815S10AXM 48 5 26 15 66.7 3 81 100 Suffix “3”means 3 K Vdc isolation Type M = Semi regulated The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de RS2 - XX XX X XX Power (W) Input Type A X M Code internal Isolation (kVDC) 10=1.00 20=2.00 RS2 - XX XX X XX Power (W) Input Type A X M Code internal Isolation (kVDC) 10=1.00 20=2.00

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. DC/DC-Converter RS2-S10M/D10M 1.0W semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiatednoise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications.

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RS2-XXXXS10A1M RS2-XXXXS10A1M DC/DC-Converter RS2-S10M/D10M 1.0W semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28