RS2-0505D20AXM

RS2-0505D20AXM RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS2-S20M/D20M 2.0W Semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 7 Pin SIL Package
• 1000VDC Isolation
• Up to 3000VDC Isolation
• Low Ripple and Noise
• Efficiency up to 89%
• Operating Temperature Range: -40° ~ +85°C
• Non Conductive Black Plastic Case
• EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±2~4% Line regulation: per 1%Vin Change: ±1.2% LOAD REGULATION: from 10% to 100% Load: see table Ripple noise: 50mV pK -pk Temperature coefficient: ±0.02%°C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 25-40mA pk-pk by 5-24V GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 70kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.9MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: C5191R-H Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 2.8g Dimmension SIP: 0.76 x 0.28 x 0.39“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 9VDC max

12V Models: 18VDC max 15V Models: 20VDC max 24V Models: 30VDC max Soldering Temperature: 260°C max. EMC SPECIFICATIONS (2) Radiated-/Conducted Emissions: EN55022 Class B (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (5) STAND Juni 2016 Rev 01 RS2 - XX XX X XX Power (W) Input Type A X M Code internal Isolation (kVDC) 10=1.00 20=2.00 MODEL SELECTION GUIDE Suffix “3”means 3 K Vdc isolation Type M = Semi regulated NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de 1. Ripple/Noise measured with 20MHz bandwidth and 1.0uF ceramic capacitor. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads shouldbe minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. MODEL NUMBER INPUT Voltage Range INPUT Current OUTPUT Voltage OUTPUT Current Full load LOAD Regulation EFFICIENCY CapacitorNo-Load Full Load RS2- 0505D20AXM 5 50 488 ±5 ±200 5 82 ±100 RS2-0509D20AXM 5 50 471 ±9 ±111.1 3.9 85 ±100 RS2-0512D20AXM 5 50 465 ±12 ±83.3 3.7 86 ±47 RS2-0515D20AXM 5 50 460 ±15 ±66.6 4 87 ±47 RS2-1205D20AXM 12 40 200 ±5 ±200 3.4 84 ±100 RS2-1209D20AXM 12 40 189 ±9 ±111.1 2.4 88 ±100 RS2-1212D20AXM 12 40 187 ±12 ±83.3 2.2 89 ±47 RS2-1215D20AXM 12 40 187 ±15 ±66.6 1.9 89 ±47 RS2-1505D20AXM 15 30 157 ±5 ±200 3.4 85 ±100 RS2-1509D20AXM 15 30 152 ±9 ±111.1 2.4 88 ±100 RS2-1512D20AXM 15 30 152 ±12 ±83.3 2.2 88 ±47 RS2-1515D20AXM 15 30 152 ±15 ±66.6 1.9 88 ±47 RS2-2405D20AXM 24 20 102 ±5 ±200 3.5 82 ±100 RS2-2409D20AXM 24 20 98 ±9 ±111.1 2.4 85 ±100 RS2-2412D20AXM 24 20 97 ±12 ±83.3 2.2 86 ±47 RS2-2415D20AXM 24 20 96 ±15 ±66.6 1.9 87 ±47 RS2-0505S20 AXM 5 50 494 5 400 6 81 220 RS2-0509S20AXM 5 50 471 9 222.2 4.2 85 220 RS2-0512S20AXM 5 50 471 12 166.6 3.8 85 100 RS2-0515S20AXM 5 50 465 15 133.3 4.5 86 100 RS2-1205S20AXM 12 40 198 5 400 4.2 84 220 RS2-1209S20AXM 12 40 194 9 222.2 2.8 86 220 RS2-1212S20AXM 12 40 189 12 166.6 2.4 88 100 RS2-1215S20AXM 12 40 189 15 133.3 2.2 88 100 RS2-1505S20AXM 15 30 157 5 400 4 85 220 RS2-1509S20AXM 15 30 153 9 222.2 2.6 87 220 RS2-1512S20AXM 15 30 153 12 166.6 2.4 87 100 MODEL SELECTION GUIDE Suffix “3”means 3 K Vdc isolation Type M = Semi regulated NOTE The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg -electronic.de 1. Ripple/Noise measured with 20MHz bandwidth and 1.0uF ceramic capacitor. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads shouldbe minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. MODEL NUMBER INPUT Voltage Range INPUT Current OUTPUT Voltage OUTPUT Current Full load LOAD Regulation EFFICIENCY CapacitorNo-Load Full Load RS2- 0505D20AXM 5 50 488 ±5 ±200 5 82 ±100 RS2-0509D20AXM 5 50 471 ±9 ±111.1 3.9 85 ±100 RS2-0512D20AXM 5 50 465 ±12 ±83.3 3.7 86 ±47 RS2-0515D20AXM 5 50 460 ±15 ±66.6 4 87 ±47 RS2-1205D20AXM 12 40 200 ±5 ±200 3.4 84 ±100 RS2-1209D20AXM 12 40 189 ±9 ±111.1 2.4 88 ±100 RS2-1212D20AXM 12 40 187 ±12 ±83.3 2.2 89 ±47 RS2-1215D20AXM 12 40 187 ±15 ±66.6 1.9 89 ±47 RS2-1505D20AXM 15 30 157 ±5 ±200 3.4 85 ±100 RS2-1509D20AXM 15 30 152 ±9 ±111.1 2.4 88 ±100 RS2-1512D20AXM 15 30 152 ±12 ±83.3 2.2 88 ±47 RS2-1515D20AXM 15 30 152 ±15 ±66.6 1.9 88 ±47 RS2-2405D20AXM 24 20 102 ±5 ±200 3.5 82 ±100 RS2-2409D20AXM 24 20 98 ±9 ±111.1 2.4 85 ±100 RS2-2412D20AXM 24 20 97 ±12 ±83.3 2.2 86 ±47 RS2-2415D20AXM 24 20 96 ±15 ±66.6 1.9 87 ±47 RS2-0505S20 AXM 5 50 494 5 400 6 81 220 RS2-0509S20AXM 5 50 471 9 222.2 4.2 85 220 RS2-0512S20AXM 5 50 471 12 166.6 3.8 85 100 RS2-0515S20AXM 5 50 465 15 133.3 4.5 86 100 RS2-1205S20AXM 12 40 198 5 400 4.2 84 220 RS2-1209S20AXM 12 40 194 9 222.2 2.8 86 220 RS2-1212S20AXM 12 40 189 12 166.6 2.4 88 100 RS2-1215S20AXM 12 40 189 15 133.3 2.2 88 100 RS2-1505S20AXM 15 30 157 5 400 4 85 220 RS2-1509S20AXM 15 30 153 9 222.2 2.6 87 220 RS2-1512S20AXM 15 30 153 12 166.6 2.4 87 100 DC/DC-Converter RS2-S20M/D20M 2.0W Semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% LOAD 60% 80% 100% LoLine/Iin Nominal/Iin HiLine/Iin EFFICIENCYVSOUTPUTCURRENT LOAD 100% Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% 60% LOAD Nominal/Iin 80% 100% Lo Line/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 0% 10% 20% 40% 60% LOAD 80% 100% Lo Line/Iin Nominal/Iin Hi Line/Iin Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1,L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-12XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-15XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-24XXS20/D20AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2 -0505S20A XM RS2 -2405S20A XM RS2 -051 5S20A XM RS2 -2415S20A XM +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter 1uF Scope -Vout E ffic ie n c y (% ) Efficiency(%) E f f i c i e n c y ( % ) E ffic ie n c y (% ) EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% LOAD 60% 80% 100% LoLine/Iin Nominal/Iin HiLine/Iin EFFICIENCYVSOUTPUTCURRENT LOAD 100% Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% 60% LOAD Nominal/Iin 80% 100% Lo Line/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 0% 10% 20% 40% 60% LOAD 80% 100% Lo Line/Iin Nominal/Iin Hi Line/Iin Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1,L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-12XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-15XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-24XXS20/D20AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2 -0505S20A XM RS2 -2405S20A XM RS2 -051 5S20A XM RS2 -2415S20A XM +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter 1uF Scope -Vout E ffic ie n c y (% ) Efficiency(%) E f f i c i e n c y ( % ) E ffic ie n c y (% ) EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% LOAD 60% 80% 100% LoLine/Iin Nominal/Iin HiLine/Iin EFFICIENCYVSOUTPUTCURRENT LOAD 100% Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% 60% LOAD Nominal/Iin 80% 100% Lo Line/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 0% 10% 20% 40% 60% LOAD 80% 100% Lo Line/Iin Nominal/Iin Hi Line/Iin Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1,L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-12XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-15XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-24XXS20/D20AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2 -0505S20A XM RS2 -2405S20A XM RS2 -051 5S20A XM RS2 -2415S20A XM +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter 1uF Scope -Vout E ffic ie n c y (% ) Efficiency(%) E f f i c i e n c y ( % ) E ffic ie n c y (% ) DC/DC-Converter RS2-S20M/D20M 2.0W Semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% LOAD 60% 80% 100% LoLine/Iin Nominal/Iin HiLine/Iin EFFICIENCYVSOUTPUTCURRENT LOAD 100% Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% 60% LOAD Nominal/Iin 80% 100% Lo Line/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 0% 10% 20% 40% 60% LOAD 80% 100% Lo Line/Iin Nominal/Iin Hi Line/Iin Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1,L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-12XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-15XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-24XXS20/D20AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2 -0505S20A XM RS2 -2405S20A XM RS2 -051 5S20A XM RS2 -2415S20A XM +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter 1uF Scope -Vout E ffic ie n c y (% ) Efficiency(%) E f f i c i e n c y ( % ) E ffic ie n c y (% ) EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% LOAD 60% 80% 100% LoLine/Iin Nominal/Iin HiLine/Iin EFFICIENCYVSOUTPUTCURRENT LOAD 100% Lo Line/Iin Nominal/Iin Hi Line/Iin EFFICIENCYVSOUTPUTCURRENT 0% 10% 20% 40% 60% LOAD Nominal/Iin 80% 100% Lo Line/Iin Hi Line/Iin EFFICIENCY VS OUTPUT CURRENT 0% 10% 20% 40% 60% LOAD 80% 100% Lo Line/Iin Nominal/Iin Hi Line/Iin Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1,L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C1 L C2 C3 RS2-05XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-12XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-15XXS20/D20AXM 1210, 2.2uF/100V 18uH RS2-24XXS20/D20AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2 -0505S20A XM RS2 -2405S20A XM RS2 -051 5S20A XM RS2 -2415S20A XM +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter 1uF Scope -Vout E ffic ie n c y (% ) Efficiency(%) E f f i c i e n c y ( % ) E ffic ie n c y (% )

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RS2-XXXXS20A1M RSG RS2-XXXXS20A1M RSG DC/DC-Converter RS2-S20M/D20M 2.0W Semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28