RS1 MULTICOMP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 3

Technical content

Fast Recovery Power Diodes RS1 Series Page <1> 28/05/12 V1.1 www.element14.com www.farnell.com www.newark.com Features :

  • • For surface mounted application
  • • Glass passivated junction chip
  • • Built-in strain relief, ideal for automated placement
  • • Fast switching for high efficiency
  • • High temperature soldering : 250°C / 10 seconds at terminals SMA / DO-214 AC Dimensions : Millimetres Foot Print Dimensions Length Width Depth X Y Z Dimensions : Millimetres Mechanical Data : Cases : Moulded plastic Terminals : Solder plated Polarity : Indicated by cathode band

Fast Recovery Power Diodes RS1 Series Page <2> 26/05/12 V1.1 www.element14.com www.farnell.com www.newark.com Rating at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number RS1A RS1B RS1D RS1G RS1J Unit Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 VMaximum RMS Voltage 35 70 140 280 420 Maximum DC Blocking Voltage 50 100 200 400 600 Maximum Average Forward Rectified Current See Figure 1 at T L = 90°C 1 A Peak Forward Surge Current, 8.3 ms Single Half Sinewave Superimposed on Rated Load (JEDEC method) Maximum Instantaneous Forward Voltage at 1 A 1.3 V Maximum DC Reverse Current at TA = 25°C at Rated DC Blocking Voltage at TA = 125°C 50 µA Maximum Reverse Recovery Time (Note 1) 150 250 nS Typical Junction Capacitance (Note 2) 10 pF Typical Thermal Resistance (Note 3) RθJA RθJL 105 32 °C / W Operating Temperature Range TJ -55 to +150 °C Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1 A, IRR = 0.25 A 2. Measured at 1 MHz and Applied V R = 4 Volts 3. Thermal Resistance from Junction to Ambient and from Junction to Lead Mounted on PCB with 0.2 × 0.2 inches (5 × 5 mm) Copper Pad Areas Average Forward Current (A) Lead Temperature (°C) Peak Forward Surge Current (A) Number of Cycles AT 60 Hz Notes : Maximum Ratings and Electrical Characteristics Ratings and Characteristic Curves Figure 1 Maximum Forward Current Derating Curve Figure 2 Maximum Non-Repetitive Forward Surge Current

Fast Recovery Power Diodes RS1 Series Page <3> 26/05/12 V1.1 www.element14.com www.farnell.com www.newark.com Figure 3 Typical Instantaneous Forward Characteristics Per Leg Figure 4 Typical Reverse Characteristics Instantaneous Forward Current (A) Forward Voltage (V) Instantaneous Forward Current (µA) Percent of Rated Peak Reverse (%) Figure 5 Typical Junction Capacitance Junction Capacitance (PF) Reverse Voltage (V) Specification Table IF (av) (A) VRRM (V) IFSM (A) trr maximum (nS) VF (V) at IF = 1 (A) Package Part Number 150

1.3 DO -214 AC

(SMA) RS1A

100 RS1B

200 RS1D

400 RS1G

Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.