RS1-0515S10A1

RS1-0303S10AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (5) STAND Juni 2016 Rev 01 DC/DC-Converter RS1/RD1-S10 1.0W unregulated Single Output we energize electronics! an acal group company we energize electronics!

• 4 Pin SIL/ 8Pin DIL Package
• 1000VDC Isolation
• Up to 3000VDC Isolation
• Low Ripple and Noise
• Efficiency up to 83%
• Operating Temperature Range: -40° ~ +85°C
• Non Conductive Black Plastic Case
• EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: ±1.2% (per 1%Vin Change) LOAD REGULATION: ±10% ( from 20 to 100%) Load Output 3.3V Model: ±20% Ripple noise (20Mhz bandwidth): 100mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: see table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: see table No-Load/Full-Load Input Current: see table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 80kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.121MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material SIP Case: Ø 0.5mm Alloy42 Solder-coated PIN Material DIP Case: Ø 0.5mm Brass Solder-coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 1.5g Weight Case-DIP: 1.8g Dimmension SIP: 0.46 x 0.24 x 0.40“ Dimmension DIP: 0.50 x 0.40 x 0.27“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 3.3V Models: 6VDC max

5 V Models: 7VDC max

12V Models: 15VDC max 15V Models: 18VDC max 24V Models: 28VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class B ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (5) STAND Juni 2016 Rev 01 RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V DC/DC-Converter RS1/RD1-S10 1.0W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation MODEL SELECTION GUIDE MODELNUMBER INPUT INPUTCurrent OUTPUT OUTPUTCurrent VoltageRange No-Load FullLoad Voltage Fullload EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RS1-0303S10AX 3.3 25 421 3.3 303 72 220 RS1-0305S10AX 3.3 25 394 5 200 77 220 RS1-0307S10AX 3.3 25 384 7.2 139 79 220 RS1-0309S10AX 3.3 30 404 9 111 75 220 RS1-0312S10AX 3.3 45 473 12 100 77 220 RS1-0315S10AX 3.3 35 384 15 67 79 220 RS1-0318S10AX 3.3 35 399 18 56 76 220 RS1-0324S10AX 3.3 53 461 24 50 79 220 RS1-0503S10AX 5 20 257 3.3 303 78 220 RS1-0505S10AX 5 25 247 5 200 81 220 RS1-0507S10AX 5 16 241 7.2 139 83 220 RS1-0509S10AX 5 26 250 9 111 80 220 RS1-0512S10AX 5 25 300 12 100 80 220 RS1-0515S10AX 5 35 244 15 67 82 220 RS1-0518S10AX 5 25 247 18 56 81 220 RS1-0524S10AX 5 35 289 24 50 83 220 RS1-1203S10AX 12 15 107 3.3 303 78 220 RS1-1205S10AX 12 16 105 5 200 79 220 RS1-1207S10AX 12 16 100 7.2 139 83 220 RS1-1209S10AX 12 15 107 9 111 78 220 RS1-1212S10AX 12 15 125 12 100 80 220 RS1-1215S10AX 12 15 105 15 67 79 220 RS1-1218S10AX 12 20 104 18 56 80 220 RS1-1224S10AX 12 25 123 24 50 81 220 RS1-1503S10AX 15 15 89 3.3 303 75 220 RS1-1505S10AX 15 9 82 5 200 81 220 RS1-1507S10AX 15 12 88 7.2 139 76 220 RS1-1509S10AX 15 10 90 9 111 74 220 RS1-1512S10AX 15 13 100 12 100 80 220 RS1-1515S10AX 15 15 84 15 67 79 220 RS1-1518S10AX 15 12 85 18 56 78 220 RS1-1524S10AX 15 10 99 24 50 81 220 RS1-2403S10AX 24 8 54 3.3 303 77 220 RS1-2405S10AX 24 8 52 5 200 80 220 RS1-2407S10AX 24 10 54 7.2 139 77 220 RS1-2409S10AX 24 7 54 9 111 77 220 RS1-2412S10AX 24 8 62 12 100 80 220 RS1-2415S10AX 24 8 51 15 67 81 220 RS1-2418S10AX 24 8 52 18 56 80 220 RS1-2424S10AX 24 9 60 24 50 83 220 RS1-4803S10AX 48 6 29 3.3 303 73 220 RS1-485S10AX 48 6 28 5 200 74 220 RS1-4807S10AX 48 7 27 7.2 139 77 220 RS1-4809S10AX 48 5 27 9 111 78 220 RS1-4812S10AX 48 5 32 12 100 77 220 RS1-4815S10AX 48 5 27 15 67 76 220 RS1-4818S10AX 48 8 28 18 56 75 220 RS1-4824S10AX 48 8 31 24 50 80 220 Suffix “3”means 3 KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (5) STAND Juni 2016 Rev 01 MODELNUMBER INPUT INPUTCurrent OUTPUT OUTPUTCurrent VoltageRange No-Load FullLoad Voltage Fullload EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RD1-0303S10AX 3.3 25 410 3.3 303 74 220 RD1-0305S10AX 3.3 25 394 5 200 77 220 RD1-0307S10AX 3.3 30 404 7.2 139 75 220 RD1-0309S10AX 3.3 30 399 9 111 76 220 RD1-0312S10AX 3.3 45 485 12 100 75 220 RD1-0315S10AX 3.3 25 384 15 67 79 220 RD1-0318S10AX 3.3 35 399 18 56 76 220 RD1-0324S10AX 3.3 90 485 24 50 75 220 RD1-0503S10AX 5 16 256 3.3 303 78 220 RD1-0505S10AX 5 15 253 5 200 79 220 RD1-0507S10AX 5 16 241 7.2 139 83 220 RD1-0509S10AX 5 25 253 9 111 79 220 RD1-0512S10AX 5 25 296 12 100 81 220 RD1-0515S10AX 5 25 244 15 67 82 220 RD1-0518S10AX 5 25 241 18 56 83 220 RD1-0524S10AX 5 28 293 24 50 82 220 RD1-1203S10AX 12 15 108 3.3 303 77 220 RD1-1205S10AX 12 16 105 5 200 79 220 RD1-1207S10AX 12 16 100 7.2 139 83 220 RD1-1209S10AX 12 15 105 9 111 79 220 RD1-1212S10AX 12 8 125 12 100 80 220 RD1-1215S10AX 12 17 105 15 67 79 220 RD1-1218S10AX 12 15 103 18 56 81 220 RD1-1224S10AX 12 25 127 24 50 79 220 RD1-1503S10AX 15 15 89 3.3 303 75 220 RD1-1505S10AX 15 10 83 5 200 80 220 RD1-1507S10AX 15 12 88 7.2 139 76 220 RD1-1509S10AX 15 10 85 9 111 78 220 RD1-1512S10AX 15 13 98 12 100 82 220 RD1-1515S10AX 15 15 83 15 67 80 220 RD1-1518S10AX 15 12 85 18 56 78 220 RD1-1524S10AX 15 10 99 24 50 81 220 RD1-2403S10AX 24 8 53 3.3 303 79 220 RD1-2405S10AX 24 8 53 5 200 79 220 RD1-2407S10AX 24 10 56 7.2 139 74 220 RD1-2409S10AX 24 7 53 9 111 79 220 RD1-2412S10AX 24 8 63 12 100 80 220 RD1-2415S10AX 24 8 52 15 67 80 220 RD1-2418S10AX 24 8 51 18 56 82 220 RD1-2424S10AX 24 9 61 24 50 82 220 Suffix “3”means 3 KVdc isolation MODEL SELECTION GUIDE DC/DC-Converter RS1/RD1-S10 1.0W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (5) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS10AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS10AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS10AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS10AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS10AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS10AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS10AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. DC/DC-Converter RS1/RD1-S10 1.0W unregulated Single Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 5 (5) STAND Juni 2016 Rev 01 RS1-XXXXS10A1 RD1-XXXXS10A1RS1-XXXXS10A1 RD1-XXXXS10A1 RS1-XXXXS10A1 RD1-XXXXS10A1 DC/DC-Converter RS1/RD1-S10 1.0W unregulated Single Output we energize electronics! an acal group company we energize electronics!

4 PIN SIL 8 PIN DIL

The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28