RS1-0503S20AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (3) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS1-S20 2.0W unregulated Single Output we energize electronics! an acal group company we energize electronics!

  • 4 Pin SIL Package
  • 1000VDC Isolation
  • Up to 3000VDC Isolation
  • Low Ripple and Noise
  • Efficiency up to 88%
  • Operating Temperature Range: -40° ~ +85°C
  • Non Conductive Black Plastic Case
  • EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: ±1.2% (per 1%Vin Change) LOAD REGULATION: ±10% ( from 20 to 100%) Load Output 3.3V Model: ±20% Ripple noise (20Mhz bandwidth): 150mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: see table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: see table No-Load/Full-Load Input Current: see table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 70kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.121MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material SIP Case: Ø 0.5mm Alloy42 Solder-coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 1.8g Dimmension SIP: 0.46 x 0.29 x 0.40“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 7VDC max

12V Models: 15VDC max 15V Models: 18VDC max 24V Models: 28VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class B ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (3) STAND Juni 2016 Rev 01 RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current Voltage No-Load Full Load Voltage Full load EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RS1-0503S20AX 5 35 371 3.3 400 71 470 RS1-0505S20AX 5 35 519 5 400 77 470 RS1-0507S20AX 5 35 519 7.2 278 77 470 RS1-0509S20AX 5 35 500 9 222 80 470 RS1-0512S20AX 5 35 487 12 167 82 470 RS1-0515S20AX 5 35 487 15 133 82 470 RS1-0518S20AX 5 35 487 18 111 82 470 RS1-0524S20AX 5 35 487 24 83 82 470 RS1-1203S20AX 12 20 152 3.3 400 72 470 RS1-1205S20AX 12 20 213 5 400 78 470 RS1-1207S20AX 12 20 208 7.2 278 80 470 RS1-1209S20AX 12 20 203 9 222 82 470 RS1-1212S20AX 12 20 198 12 167 84 470 RS1-1215S20AX 12 20 198 15 133 84 470 RS1-1218S20AX 12 20 198 18 111 84 470 RS1-1224S20AX 12 25 203 24 83 82 470 RS1-1503S20AX 15 18 120 3.3 400 73 470 RS1-1505S20AX 15 18 170 5 400 78 470 RS1-1507S20AX 15 18 166 7.2 278 80 470 RS1-1509S20AX 15 18 162 9 222 82 470 RS1-1512S20AX 15 18 158 12 167 84 470 RS1-1515S20AX 15 18 158 15 133 84 470 RS1-1518S20AX 15 18 158 18 111 84 470 RS1-1524S20AX 15 18 162 24 83 82 470 RS1-2403S20AX 24 10 74 3.3 400 74 470 RS1-2405S20AX 24 10 104 5 400 80 470 RS1-2407S20AX 24 10 104 7.2 278 80 470 RS1-2409S20AX 24 10 99 9 222 84 470 RS1-2412S20AX 24 10 99 12 167 84 470 RS1-2415S20AX 24 10 99 15 133 84 470 RS1-2418S20AX 24 10 99 18 111 84 470 RS1-2424S20AX 24 10 99 24 83 84 470 RS1-4803S20AX 48 7 38 3.3 400 72 470 RS1-485S20AX 48 7 53 5 400 78 470 RS1-4807S20AX 48 7 52 7.2 278 80 470 RS1-4809S20AX 48 7 51 9 222 82 470 RS1-4812S20AX 48 7 52 12 167 80 470 RS1-4815S20AX 48 7 51 15 133 82 470 RS1-4818S20AX 48 7 51 18 111 82 470 RS1-4824S20AX 48 7 51 24 83 82 470 Suffix “3”means 3 KVdc isolation DC/DC-Converter RS1-S20 2.0W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (3) STAND Juni 2016 Rev 01 EMI Filter Input filter components (C1, L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. C1 L C2 C3 RS1-05XXS20AX 1210, 2.2uF/100V 18uH RS1-12XXS20AX 1210, 2.2uF/100V 18uH RS1-15XXS20AX 1210, 2.2uF/100V 18uH RS1-24XXS20AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1-48XXS20AX Electrolytic Capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000- 4-4. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 EMI Filter Input filter components (C1, L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. C1 L C2 C3 RS1-05XXS20AX 1210, 2.2uF/100V 18uH RS1-12XXS20AX 1210, 2.2uF/100V 18uH RS1-15XXS20AX 1210, 2.2uF/100V 18uH RS1-24XXS20AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1-48XXS20AX Electrolytic Capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000- 4-4. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 EMI Filter Input filter components (C1, L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. C1 L C2 C3 RS1-05XXS20AX 1210, 2.2uF/100V 18uH RS1-12XXS20AX 1210, 2.2uF/100V 18uH RS1-15XXS20AX 1210, 2.2uF/100V 18uH RS1-24XXS20AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1-48XXS20AX Electrolytic Capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000- 4-4. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 DC/DC-Converter RS1-S20 2.0W unregulated Single Output we energize electronics! an acal group company we energize electronics! RS1-XXXXS20A1 RS1-XXXXS20A1 (The Pin Connection of high isolation one is the same with normal one). The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28