RR9-2403S12A1 RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR9-S12/D12 12.0W 4:1 Regulated Single & Dual Output

  • 24 Pin DIL Package
  • Wide 4:1 Input Range
  • 1600VDC Isolation
  • No Minimum Load Required
  • Continuous Short Circuit Protection
  • Over Voltage Protection
  • Over Current Protection
  • Efficiency up to 90%
  • Operating Temperature Range -40° ~ +85°C
  • Metal Case
  • Soft Start
  • Remote on/off Control OUTPUT SPECIFICATION Voltage accuracy: ±1.2% Line regulation: Single &Dual ±0.2% max. LOAD REGULATION: from 0% to 100% Load: ±0.5 - 1% max. Cross Regulation (Dual Output): ± 5% Over Voltage Protection (Zener diode clamp): Zener Diode Clamp Over Current Protection: 170%of Fl, typ.. Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 85mV pk-pk Temperature coefficient: ±0.02%/°C Capacitor load: See table Transient Recovery Time: 250us,typ. Transient Response: (Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 20ms,typ. Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 20mA pk-pk typ. Remote On/Off (positive logic): On: 3.0~12VDC or open circuit, OFF: 0~1.2VDC or Short circuit pin 1 and 2/3 OFF idle current: 5mA typ. GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage (60sec): 1600VDC, Input/Output, Case/Input & Output I/O Isolation Capacitance: 1500pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 270kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Nickel-coated Copper PIN Material: 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 18.0g Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 24V Models: 50VDC max. 48V Models: 100VDC max. Soldering Temperature: 260°C max. EMC SPECIFICATIONS (2) Radiated-/Conducted Emissions: EN55022 Class A see EMI Filter ESD: IEC 61000-4-2 Perf.Criteria B RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A DC/DC-Converter 12.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01

6.0W Regulated Single & Dual Output DC/DC-Converter 12.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 2. Measured with 20MHz bandwidth and 1.0uF ceramic capacitor. 3. Tested by minimal Vin and constant resistive load. 4. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ). 5. Input filter components (C1, L, C2) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 6. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5 and IEC61000-4-6 . The filter capacitor RSG suggest: Nippon - chemi - con KY series, 330uF/100V. 7. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. +Vout +Vin L DC/DC Converter Load -Vin -Vout Derating Curve 100% 75% 50% 25% -40 -20 0 20 40 60 80 85 105 120 AMBIENT TEMPERATURE(° C) MODEL SELECTION GUIDE RR9-2403S12A1 9-36 15 573 3.3 0 3500 87 2000 RR9-2405S12A1 9-36 15 581 5.1 0 2400 89 2000 RR9-2412S12A1 9-36 15 574 12 0 1000 90 430 RR9-2415S12A1 9-36 15 574 15 0 800 90 300 RR9-2405D12A1 9-36 15 595 ±5 0 ±1200 87 ±1250 RR9-2412D12A1 9-36 15 574 ±12 0 ±500 90 ±200 RR9-2415D12A1 9-36 15 574 ±15 0 ±400 90 ±120 RR9-4803S12A1 18-75 15 286 3.3 0 3500 87 2000 RR9-4805S12A1 18-75 15 290 5.1 0 2400 89 2000 RR9-4812S12A1 18-75 15 287 12 0 1000 90 430 RR9-4815S12A1 18-75 15 287 15 0 800 90 300 RR9-4805D12A1 18-75 15 297 ±5 0 ±1200 87 ±1250 RR9-4812D12A1 18-75 15 287 ±12 0 ±500 90 ±200 RR9-4815D12A1 18-75 15 287 ±15 0 ±400 90 ±120 C1 L C2 2.2uF, 100V 12uH 2.2uF, 100VRR9-XXXXS12 2.2uF, 100V 12uH 2.2uF, 100V The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : sales@motien.com.tw S.O.A. OUTPUTPOWER MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR9-XXXXD12 RR9 - XX XX S/D XX Power (W) Input Type A X Code internal Isolation (kVDC)

6.0W Regulated Single & Dual Output DC/DC-Converter 12.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 VV - 12W 4:1 Regulated Single & Dual output E F F IC IE N C Y V S O U T P U T C U R R E N T 1 00 9 5 9 0 8 5 8 0 7 5 7 0 Lo Line Nominal Hi Line 0 % 2 0 % 4 0 % 6 0 % 8 0 % 1 0 0 % 1 2 0 % 1 4 0 % L o a d (% ) E F F IC IE NC Y V S O UT P UT C UR R E NT 1 00 9 5 9 0 8 5 8 0 7 5 7 0 Nominal Lo Line Hi Line 0 % 2 0 % 4 0 % 6 0 % 8 0 % 1 0 0 % 1 2 0 % 1 4 0 % L o ad E F F IC IE NC Y V S O UT P UT C UR R E NT 1 0 0 9 5 9 0 8 5 8 0 7 5 7 0 Lo Line Nominal Hi Line 0 % 2 0 % 4 0 % 6 0 % 8 0 % 1 0 0 % 1 2 0 % 1 4 0 % L o ad E F F IC IE N C Y V S O U T P U T C U R R E N T 1 00 9 5 9 0 Lo Line Nominal 8 5 8 0 7 5 Hi Line 7 0 0 % 2 0 % 4 0 % 6 0 % 8 0 % 1 0 0 % 1 2 0 % 1 4 0 % L o a d (% ) +Vout +VinLin Current Probe Cin DC/DC Converter Load -Vin -Vout Copper Strip +Vout Single DC/DC Converter 1uF Cout Scope -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Resistive Load RR9-245R1S12 RR9-4812S12 RR9 -2412D12 RR9 -4815D12 The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : sales@motien.com.tw Efficiency(%)Efficiency(%) Efficiency(%)Efficiency(%) TEST CONFIGURATIONS

6.0W Regulated Single & Dual Output DC/DC-Converter 12.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 • Rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 VV - 12W 4:1 Regulated Single & Dual output 31.8 (1.25) 2.0 (0.08) 22.86 (0.90) 1 2 3 9 11 DC-DC CONVERTER RR9-2405D12 In: 9~36Vdc Out: ±5Vdc ±1200mA RSG 0.50 (0.02) 20.3 (0.80) DIA 1.0 (0.04) Bottom View 15.24 (0.60)4.42 (0.17) XXXX 5.01 (0.19) 23 22 16 14 0.50 (0.02) Printed Face 2.54 (0.10) 5.08 (0.20) 0.5 (0.02) 10.2 (0.4) 3.00 (0.12)

24 Pin DIL Package

All dimensionsare typical in millimeters ( inches). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 4. Stand-off tolerance: ±0.1 ( ±0.004 ) PIN CONNECTIONS PIN NUMBER SINGLE DUAL

1 Remote On/Off Remote On/Off

9 N.P. Common 11 N.C. -V Output 14 +V Output +V Output 16 -V Output Common 22 +V Input +V Input 23 +V Input +V Input MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28