RR6-4824D05A1

RR6-2403S05AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR6-S05/D05 5.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 24 Pin DIL Package
• Wide 4:1 Input Range
• 1500VDC Isolation
• Up to 3500VDC Isolation
• Continuous Short Circuit Protection
• Efficiency up to 83%
• Operating Temperature Range -40° ~ +85°C
• Metal Case Standard , Optional Plastic Case OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. LOAD REGULATION: ±0.5% Output 3.3V Model: ±1.5% Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1500 ~ 3500VDC I/O Isolation Capacitance: 470pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 266kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.21MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Nickel-coated Copper Base Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 13.5g (plastic), 17.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR6 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) DC/DC-Converter RR6-S05/D05 5.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MODEL SELECTION GUIDE MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) Load (uF) RR6-2403S05AX 9-36 18 238.3 3.3 0 1300 75 1000 RR6-2405S05AX 9-36 18 263.7 5 0 1000 79 1000 RR6-2407S05AX 9-36 18 254.1 7.2 0 694 82 470 RR6-2409S05AX 9-36 18 251.0 9 0 555 83 470 RR6-2412S05AX 9-36 18 254.1 12 0 416 82 220 RR6-2415S05AX 9-36 18 254.1 15 0 333 82 68 RR6-2424S05AX 9-36 18 254.1 24 0 208 82 68 RR6-2403D05AX 9-36 18 281.5 ±3.3 0 ±757 74 ±100 RR6-2405D05AX 9-36 18 260.4 ±5 0 ±500 80 ±100 RR6-2407D05AX 9-36 18 257.2 ±7.2 0 ±347 81 ±100 RR6-2409D05AX 9-36 20 257.2 ±9 0 ±277 81 ±100 RR6-2412D05AX 9-36 20 251.0 ±12 0 ±208 83 ±68 RR6-2415D05AX 9-36 20 260.4 ±15 0 ±166 80 ±22 RR6-2424D05AX 9-36 26 263.7 ±24 0 ±104 79 ±22 RR6-4803S05AX 18-72 15 119.2 3.3 0 1300 75 1000 RR6-4805S05AX 18-72 15 130.2 5 0 1000 80 1000 RR6-4807S05AX 18-72 15 127.0 7.2 0 694 82 1000 RR6-4809S05AX 18-72 15 128.6 9 0 555 81 330 RR6-4812S05AX 18-72 15 125.5 12 0 416 83 330 RR6-4815S05AX 18-72 15 125.5 15 0 333 83 330 RR6-4824S05AX 18-72 15 128.6 24 0 208 83 47 RR6-4803D05AX 18-72 15 133.5 ±3.3 0 ±757 78 ±680 RR6-4805D05AX 18-72 15 130.2 ±5 0 ±500 80 ±330 RR6-4807D05AX 18-72 15 130.2 ±7.2 0 ±347 80 ±100 RR6-4809D05AX 18-72 15 127.0 ±9 0 ±277 82 ±100 RR6-4812D05AX 18-72 15 127.0 ±12 0 ±208 82 ±100 RR6-4815D05AX 18-72 15 130.2 ±15 0 ±166 80 ±47 RR6-4824D05AX 18-72 15 131.8 ±24 0 ±104 79 ±22 Suffix “3”means 3.5KVdc isolation Suffix “P”means Plastic case instead of standard Metal Case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@ rsg-electronic.de

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES

24 Models 48 Models

Efficiency(%) Efficiency(%) +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES Efficiency(%) Efficiency(%) +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES Efficiency(%) Efficiency(%) DC/DC-Converter RR6-S05/D05 5.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! TEST CONFIGURATIONS ELECTRICAL CHARACTERISTIC CURVES

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 MECHANICAL SPECIFICA TIONS 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) Printed Face

24 Pin DIL Package

+V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. For “P” Case 0.50 (0.02) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) Bottom View 1 2 3 9 10 11 12 24 23 22 16 15 14 13 Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ± 0.02 ) and length PIN CONNECTIONS PIN NUMBER SINGLE-H DUAL-H SINGLE +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. Bottom View 31.75 (1.25) 20.32 (0.80) 27.94 (1.10) 0.50 (0.02) 2.54 (0.10) DIA 0. 50 (0.02) 15.24 (0.60) Built-in stand- offs help air convectionPrinted Face 10.16 (0.40) 3.00 (0.12) DC-DC CONVERTER xxxx Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ±0.02 ) and length RR6-XXXXS05A1 RR6-XXXXS05A1P DC/DC-Converter RR6-S05/D05 5.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28