RR6-2403S04AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR6-S04/D04 4.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

  • 24 Pin DIL Package
  • Wide 4:1 Input Range
  • 1500VDC Isolation
  • Up to 3500VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 82%
  • Operating Temperature Range -40° ~ +85°C
  • Metal Case Standard , Optional Plastic Case OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. LOAD REGULATION: ±0.5% Output 3.3V Model: ±1.5% Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1500 ~ 3500VDC I/O Isolation Capacitance: 470pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 266kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.21MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Nickel-coated Copper Base Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 17.0g ( Metal), 13.5g (plastic) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR6 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) Load (uF) RR6-2403S04AX 9-36 18 222.0 3.3 0 1200 75 1000 RR6-2405S04AX 9-36 18 210.9 5 0 800 79 680 RR6-2407S04AX 9-36 18 208.3 7.2 0 555 80 100 RR6-2409S04AX 9-36 18 208.3 9 0 444 80 100 RR6-2412S04AX 9-36 18 203.3 12 0 333 82 100 RR6-2415S04AX 9-36 18 203.3 15 0 266 82 100 RR6-2424S04AX 9-36 18 205.8 24 0 166 81 100 RR6-2403D04AX 9-36 18 222.0 ±3.3 0 ±606 75 ±470 RR6-2405D04AX 9-36 18 210.9 ±5 0 ±400 79 ±330 RR6-2407D04AX 9-36 18 210.9 ±7.2 0 ±277 79 ±47 RR6-2409D04AX 9-36 18 205.8 ±9 0 ±222 81 ±47 RR6-2412D04AX 9-36 20 203.3 ±12 0 ±166 82 ±47 RR6-2415D04AX 9-36 20 205.8 ±15 0 ±133 81 ±22 RR6-2424D04AX 9-36 25 210.9 ±24 0 ±83 79 ±10 RR6-4803S04AX 18-72 15 110.0 3.3 0 1200 75 1000 RR6-4805S04AX 18-72 15 105.5 5 0 800 79 680 RR6-4807S04AX 18-72 15 102.8 7.2 0 555 81 680 RR6-4809S04AX 18-72 15 104.2 9 0 444 80 220 RR6-4812S04AX 18-72 15 101.6 12 0 333 82 220 RR6-4815S04AX 18-72 15 101.6 15 0 266 82 68 RR6-4824S04AX 18-72 15 104.2 24 0 166 80 47 RR6-4803D04AX 18-72 15 108.2 ±3.3 0 ±606 77 ±680 RR6-4805D04AX 18-72 15 105.5 ±5 0 ±400 79 ±330 RR6-4807D04AX 18-72 15 107.0 ±7.2 0 ±277 78 ±47 RR6-4809D04AX 18-72 15 104.2 ±9 0 ±222 80 ±47 RR6-4812D04AX 18-72 15 102.8 ±12 0 ±166 81 ±47 RR6-4815D04AX 18-72 15 101.6 ±15 0 ±133 82 ±33 RR6-4824D04AX 18-72 15 104.2 ±24 0 ±83 80 ±22 Suffix “3”means 3.5KVdc isolation The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@ rsg-electronic.de DC/DC-Converter RR6-S04/D04 4.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES

24 Models 48 Models

Efficiency(%) Efficiency(%) +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES Efficiency(%) Efficiency(%) +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Output Ripple & Noise Measurement Test Copper Strip +Vout Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load EMI Filter +Vout +Vin Input filter components (C1,C3, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L DC/DC Converter Load -Vin -Vout C1 L C3 220uF,100V 12uH 1000PF,2KV NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.It’s recommended to add C1(220 uF), C3(1000P F,2KV) , L(12u H) in input end to achieve EN55022 conducted Class A. 6.An external filter capacitor is required if the module has to meet IEC 61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal Hi Line 0% 20% 40% 60% Load 80% 100% 120% ELECTRICAL CHARACTERISTIC CURVES Efficiency(%) Efficiency(%) DC/DC-Converter RR6-S04/D04 4.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! TEST CONFIGURATION ELECTRICAL CHARACTERISTICS CURVES

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 MECHANICAL SPECIFICA TIONS 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) Printed Face

24 Pin DIL Package

+V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. For “P” Case 0.50 (0.02) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) Bottom View 1 2 3 9 10 11 12 24 23 22 16 15 14 13 Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ± 0.02 ) and length PIN CONNECTIONS PIN NUMBER SINGLE-H DUAL-H SINGLE +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. Bottom View 31.75 (1.25) 20.32 (0.80) 27.94 (1.10) 0.50 (0.02) 2.54 (0.10) DIA 0. 50 (0.02) 15.24 (0.60) Built-in stand- offs help air convectionPrinted Face 10.16 (0.40) 3.00 (0.12) DC-DC CONVERTER xxxx Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ±0.02 ) and length RR6-XXXXS04A1 RR6-XXXXS04A1P MECHANICAL SPECIFICA TIONS 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) Printed Face +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. For “P” Case 0.50 (0.02) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) Bottom View 1 2 3 9 10 11 12 24 23 22 16 15 14 13 Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ± 0.02 ) and length PIN CONNECTIONS PIN NUMBER SINGLE-H DUAL-H SINGLE +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. Bottom View 31.75 (1.25) 20.32 (0.80) 27.94 (1.10) 0.50 (0.02) 2.54 (0.10) DIA 0. 50 (0.02) 15.24 (0.60) Built-in stand- offs help air convectionPrinted Face 10.16 (0.40) 3.00 (0.12) DC-DC CONVERTER xxxx Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ± 0.35 ( ± 0.014 ) 3. Case Tolerance: ± 0.5 ( ±0.02 ) and length RR6-XXXXS04A1 RR6-XXXXS04A1P DC/DC-Converter RR6-S04/D04 4.0W 4:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28