RR4-1203S06AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

  • 24 Pin DIL Package
  • Wide 2:1 Input Range
  • 1500VDC Isolation
  • Up to 3500VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 83%
  • Operating Temperature Range -40° ~ +85°C
  • Metal Case Standard , Optional Plastic Case OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. LOAD REGULATION: ±0.5% Output 3.3V Model: ±1.5% Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02%<>°C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1500 ~ 3500VDC I/O Isolation Capacitance: 500pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 266kHz, typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.21MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Nickel-coated Copper Base Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 13.5g (plastic), 17.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 12V Models: 24VDC max. 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS RR4-S06/D06

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR4 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR4-1203S06AX 9-18 30 527 3.3 0 1400 73 1000 RR4-1205S06AX 9-18 30 649 5 0 1200 77 1000 RR4-1209S06AX 9-18 30 641 9 0 666 78 680 RR4-1212S06AX 9-18 30 617 12 0 500 81 330 RR4-1215S06AX 9-18 30 625 15 0 400 80 220 RR4-1224S06AX 9-18 30 625 24 0 250 80 68 RR4-1203D06AX 9-18 30 527 ±3.3 0 ±909 73 ±680 RR4-1205D06AX 9-18 30 649 ±5 0 ±600 77 ±330 RR4-1209D06AX 9-18 30 625 ±9 0 ±333 80 ±220 RR4-1212D06AX 9-18 30 625 ±12 0 ±250 80 ±100 RR4-1215D06AX 9-18 30 632 ±15 0 ±200 79 ±47 RR4-1224D06AX 9-18 30 625 ±24 0 ±125 80 ±33 RR4-2403S06AX 18-36 20 256 3.3 0 1400 75 1000 RR4-2405S06AX 18-36 20 313 5 0 1200 80 1000 RR4-2409S06AX 18-36 20 304 9 0 666 82 680 RR4-2412S06AX 18-36 20 313 12 0 500 80 330 RR4-2415S06AX 18-36 20 304 15 0 400 82 220 RR4-2424S06AX 18-36 20 305 24 0 250 82 68 RR4-2403D06AX 18-36 20 333 ±3.3 0 ±909 75 ±680 RR4-2405D06AX 18-36 20 321 ±5 0 ±600 78 ±330 RR4-2409D06AX 18-36 20 301 ±9 0 ±333 83 ±220 RR4-2412D06AX 18-36 20 312 ±12 0 ±250 80 ±100 RR4-2415D06AX 18-36 20 312 ±15 0 ±200 80 ±47 RR4-2424D06AX 18-36 20 312 ±24 0 ±125 80 ±33 RR4-4803S06AX 36-72 12 128 3.3 0 1400 75 1000 RR4-4805S06AX 36-72 12 156 5 0 1200 80 1000 RR4-4809S06AX 36-72 12 152 9 0 666 82 680 RR4-4812S06AX 36-72 12 156 12 0 500 80 330 RR4-4815S06AX 36-72 12 151 15 0 400 83 220 RR4-4824S06AX 36-72 12 151 24 0 250 83 68 RR4-4803D06AX 36-72 12 171 ±3.3 0 ±909 73 ±680 RR4-4805D06AX 36-72 12 158 ±5 0 ±600 79 ±330 RR4-4809D06AX 36-72 12 158 ±9 0 ±333 79 ±220 RR4-4812D06AX 36-72 12 156 ±12 0 ±250 80 ±100 RR4-4815D06AX 36-72 12 156 ±15 0 ±200 80 ±47 RR4-4824D06AX 36-72 12 156 ±24 0 ±125 80 ±33 Suffix “3”means 3.5KVdc isolation Suffix “P”means Plastic case instead of standard Metal Case DC/DC-Converter 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RR4-S06/D06

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Copper Strip +Vout Lin Current Probe Cin Load Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load

12 Models

100uF, 100V 12uH The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@ rsg-electronic.de NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 6. An external filter capacitor is required if the module has to meet IEC 61000- 4-4 and IEC 61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. Lo Line Nominal Hi Line EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF,ESR<1.0Ù at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test Use a capacitor Cout(1.0uF) measurement. The Scope measurement bandwidth is 0-20MHz. Copper Strip +Vout Lin Current Probe Cin Load Single DC/DC Converter 1uF Cout Resistive Scope Load -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load 100uF, 100V 12uH The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@ rsg-electronic.de NOTE 1. Ripple/Noise measured with a 1uF ceramic capacitor. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 6. An external filter capacitor is required if the module has to meet IEC 61000- 4-4 and IEC 61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. DC/DC-Converter 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RR4-S06/D06 N O T E TEST CONFIGURATION

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 MECHANICAL SPECIFICA TIONS PIN CONNECTIONS PIN NUMBER SINGLE V Input V Input V Input V Input +V Output +V Output N.P. Common N.C. V Output V Output Common +V Input +V Input +V Input +V Input DUAL The Pin Connection of high isolation one is the same with normal one. MECHANICAL SPECIFICA TIONS 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) Printed Face

24 Pin DIL Package

+V Output +V Output N.P. Common N.C. V Output V Output Common +V Input +V Input +V Input +V Input DUAL The Pin Connection of high isolation one is the same with normal one. For “P” Case Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) 32 11 9 32 22 14 Bottom View 0.50 (0.02) 31.75 (1.25) 20.32 (0.8) 22.86 (0.9) 2.54 (0.10) DIA 0.50 (0.02) 15.24 (0.60) Printed Face 10.16 (0.40) 3.00 (0.12) Built-in stand -offs help air convection DC-DC CONVERTER xxxx 2 3 11 16 1423 22 Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) RR4-XXXXS06A1 RR4-XXXXS06A1P MECHANICAL SPECIFICA TIONS PIN CONNECTIONS PIN NUMBER SINGLE V Input V Input V Input V Input +V Output +V Output N.P. Common N.C. V Output V Output Common +V Input +V Input +V Input +V Input DUAL The Pin Connection of high isolation one is the same with normal one. MECHANICAL SPECIFICA TIONS 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) Printed Face +V Output +V Output N.P. Common N.C. V Output V Output Common +V Input +V Input +V Input +V Input DUAL The Pin Connection of high isolation one is the same with normal one. For “P” Case Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) 32 11 9 32 22 14 Bottom View 0.50 (0.02) 31.75 (1.25) 20.32 (0.8) 22.86 (0.9) 2.54 (0.10) DIA 0.50 (0.02) 15.24 (0.60) Printed Face 10.16 (0.40) 3.00 (0.12) Built-in stand -offs help air convection DC-DC CONVERTER xxxx 2 3 11 16 1423 22 Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) RR4-XXXXS06A1 RR4-XXXXS06A1P DC/DC-Converter 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RR4-S06/D06 MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28