RR2-1205S06AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR2-S06/D06 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

  • 24 Pin DIL Package
  • Wide 2:1 Input Range
  • 1500VDC Isolation
  • Up to 3500VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 81%
  • Operating Temperature Range -40° ~ +85°C
  • Plastic Case Standard , Optional Metal Case OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. Short Circuit Protection : Continuous Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1000 ~ 3500VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 100 ~ 400kHz Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS V(1) Input Surge Voltage (100ms)/ 12V Models: 24VDC max. 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR2 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-1205S 06AX 9-18 20 735 5 300 1200 68 2200 RR2-1209S 06AX 9-18 20 694 9 167 666 72 470 RR2-1212S06AX 9-18 20 676 12 125 500 74 470 RR2-1215S06AX 9-18 20 633 15 100 400 79 470 RR2-1224S06AX 9-18 20 658 24 63 250 76 220 RR2-1205D06AX 9-18 20 649 ±5 150 600 78 ±1000 RR2-1209D06AX 9-18 20 641 ±9 83 333 78 ±220 RR2-1212D06AX 9-18 20 641 ±12 63 250 78 ±220 RR2-1215D06AX 9-18 20 625 ±15 50 200 80 ±220 RR2-1224D06AX 9-18 20 641 ±24 31 125 78 ±100 RR2-2405S06AX 18-36 12 329 5 300 1200 76 2200 RR2-2409S06AX 18-36 12 312 9 167 666 80 470 RR2-2412S06AX 18-36 12 312 12 125 500 80 470 RR2-2415S06AX 18-36 12 308 15 100 400 81 470 RR2-2424S06AX 18-36 12 325 24 63 250 77 220 RR2-2405D06AX 18-36 12 329 ±5 150 600 76 ±1000 RR2-2409D06AX 18-36 12 325 ±9 83 333 77 ±220 RR2-2412D06AX 18-36 12 312 ±12 63 250 80 ±220 RR2-2415D06AX 18-36 12 312 ±15 50 200 80 ±220 RR2-2424D06AX 18-36 12 321 ±24 31 125 78 ±100 RR2-4805S06AX 36-72 8 169 5 300 1200 74 2200 RR2-4809S06AX 36-72 8 162 9 167 666 77 470 RR2-4812S06AX 36-72 8 162 12 125 500 77 470 RR2-4815S06AX 36-72 8 158 15 100 400 79 470 RR2-4824S06AX 36-72 8 167 24 63 250 75 220 RR2-4805D06AX 36-72 8 169 ±5 150 600 74 ±1000 RR2-4809D06AX 36-72 8 164 ±9 83 333 76 ±220 RR2-4812D06AX 36-72 8 164 ±12 63 250 76 ±220 RR2-4815D06AX 36-72 8 160 ±15 50 200 78 ±220 RR2-4824D06AX 36-72 8 162 ±24 31 125 77 ±100 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de DC/DC-Converter RR2-S06/D06 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 TEST CONFIGURATIONS E Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR2-05XXS/D06AX 220uF/100V 12uH RR2-12XXS/D06AX 220uF/100V 12uH RR2-24XXS/D06AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D06AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. TEST CONFIGURATIONS E Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR2-05XXS/D06AX 220uF/100V 12uH RR2-12XXS/D06AX 220uF/100V 12uH RR2-24XXS/D06AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D06AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. DC/DC-Converter RR2-S06/D06 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! TEST CONFIGURATIONS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 MECHANICAL SPECIFICA TIONS PIN CONNECTIONS PIN NUMBER SINGLE-H DUAL-H SINGLE +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. Bottom View 31 .75 (1.25 ) 20 .32 (0.80 ) 27 .94 (1.10 ) 2.54 (0.10 ) 0.50 (0.02 ) 15 .24 (0.60 )

24 Pin DIL Package

For “M” C ase Printed Face 10 .2 (0 .4 ) 3 .00 (0 .12 ) Min . 0 .5 (0 .02 ) Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 4. Stand-off tolerance: ±0.1 ( ±0.004 ) and length RR2-XXXXS06A1 MECHANICAL SPECIFICA TIONS PIN CONNECTIONS PIN NUMBER SINGLE-H DUAL-H SINGLE +V Input +V Input V Input V Input V Input +V Output N.P. +V Output +V Output +V Output V Output N.P. V Output V Output Common N.C. N.C. N.C. N.C. -V Input N.P. N.P. N.P. +V Output DUAL +V Input N.P. +V Input -V Input +V Input V Output Common Common Common Common V Input +V Output +V Input N.P. N.P. N.C. N.P. N.P. V Input V Output V Input N.P. V Output N.P. Common +V Input +V Input N.P. N.P. N.P. N.P. N.P. Bottom View 31 .75 (1.25 ) 20 .32 (0.80 ) 27 .94 (1.10 ) 2.54 (0.10 ) 0.50 (0.02 ) 15 .24 (0.60 ) For “M” C ase Printed Face 10 .2 (0 .4 ) 3 .00 (0 .12 ) Min . 0 .5 (0 .02 ) Notes: All dimensions are typical in millimeters ( inches ). 2. Pin pitch tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) 4. Stand-off tolerance: ±0.1 ( ±0.004 ) and length RR2-XXXXS06A1 DC/DC-Converter RR2-S06/D06 6.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28