RR2-0505S02AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR2-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

FEATURES

  • 24 Pin DIL Package
  • Wide 2:1 Input Range
  • 1500VDC Isolation
  • Up to 3500VDC Isolation
  • Continuous Short Circuit Protection
  • Efficiency up to 80%
  • Operating Temperature Range -40° ~ +85°C
  • Plastic Case Standard , Optional Metal Case OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. Load regulation: Single &Dual ±0.5% max. Short Circuit Protection : Continuous Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case: 1000VDC I/O Isolation Voltage (3sec): 1000 ~ 3500VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 100 ~ 400kHz Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 5 V Models: 15VDC max. 12V Models: 24VDC max. 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR2 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-0505S02AX 4.5-9 40 588 5 100 400 68 2200 RR2-0509S02AX 4.5-9 40 571 9 55.5 222 70 470 RR2-0512S02AX 4.5-9 40 571 12 42.8 167 70 470 RR2-0515S02AX 4.5-9 40 571 15 33.3 133 70 470 RR2-0524S02AX 4.5-9 40 579 24 20.8 83 69 220 RR2-0505D02AX 4.5-9 40 588 ±5 ±50 ±200 68 ±1000 RR2-0509D02AX 4.5-9 40 571 ±9 ±27.8 ±111 70 ±220 RR2-0512D02AX 4.5-9 40 571 ±12 ±20.8 ±83 70 ±220 RR2-0515D02AX 4.5-9 40 571 ±15 ±16.8 ±67 70 ±220 RR2-0524D02AX 4.5-9 40 579 ±24 ±10.5 ±42 69 ±100 RR2-1205S02AX 9-18 20 222 5 100 400 75 2200 RR2-1209S02AX 9-18 20 213 9 55.5 222 78 470 RR2-1212S02AX 9-18 20 213 12 42.8 167 78 470 RR2-1215S02AX 9-18 20 213 15 33.3 133 78 470 RR2-1224S02AX 9-18 20 210 24 20.8 83 79 220 RR2-1205D02AX 9-18 20 225 ±5 ±50 ±200 74 ±1000 RR2-1209D02AX 9-18 20 225 ±9 ±27.8 ±111 74 ±220 RR2-1212D02AX 9-18 20 219 ±12 ±20.8 ±83 76 ±220 RR2-1215D02AX 9-18 20 216 ±15 ±16.8 ±67 77 ±220 RR2-1224D02AX 9-18 20 219 ±24 ±10.5 ±42 76 ±100 RR2-2405S02AX 18-36 12 106 5 100 400 78 2200 RR2-2409S02AX 18-36 12 104 9 55.5 222 80 470 RR2-2412S02AX 18-36 12 105 12 42.8 167 79 470 RR2-2415S02AX 18-36 12 106 15 33.3 133 78 470 RR2-2424S02AX 18-36 12 104 24 20.8 83 80 220 RR2-2405D02AX 18-36 12 111 ±5 ±50 ±200 75 ±1000 RR2-2409D02AX 18-36 12 111 ±9 ±27.8 ±111 75 ±220 RR2-2412D02AX 18-36 12 105 ±12 ±20.8 ±83 79 ±220 RR2-2415D02AX 18-36 12 105 ±15 ±16.8 ±67 79 ±220 RR2-2424D02AX 18-36 12 106 ±24 ±10.5 ±42 78 ±100 RR2-4805S02AX 36-72 8 55.5 5 100 400 75 2200 RR2-4809S02AX 36-72 8 53 9 55.5 222 78 470 RR2-4812S02AX 36-72 8 52 12 42.8 167 79 470 RR2-4815S02AX 36-72 8 52 15 33.3 133 80 470 RR2-4824S02AX 36-72 8 52 24 20.8 83 80 220 RR2-4805D02AX 36-72 8 56 ±5 ±50 ±200 74 ±1000 RR2-4809D02AX 36-72 8 55.5 ±9 ±27.8 ±111 75 ±220 RR2-4812D02AX 36-72 8 53 ±12 ±20.8 ±83 78 ±220 RR2-4815D02AX 36-72 8 53 ±15 ±16.8 ±67 78 ±220 RR2-4824D02AX 36-72 8 53 ±24 ±10.5 ±42 79 ±100 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de DC/DC-Converter RR2-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 TEST CONFIGURATIONS E Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR2-05XXS/D02AX 220uF/100V 12uH RR2-12XXS/D02AX 220uF/100V 12uH RR2-24XXS/D02AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D02AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. TEST CONFIGURATIONS E Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR2-05XXS/D02AX 220uF/100V 12uH RR2-12XXS/D02AX 220uF/100V 12uH RR2-24XXS/D02AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D02AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. DC/DC-Converter RR2-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! TEST CONFIGURATIONS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RR2-XXXXS02A1 RR2-XXXXS02A1M RR2-XXXXS02A1 RR2-XXXXS02A1M DC/DC-Converter RR2-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28