RR2-0509S03A3

RR2-0505S03AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR2-S03/D03 3.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! OUTPUT SPECIFICATION Voltage accuracy: ±1% Line regulation: Single &Dual ±0.5% max. Short Circuit Protection : Continuous Ripple noise (20Mhz bandwidth): 60mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table typ. I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec): 1000 ~ 3500VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: 100 ~ 400kHz Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material: Ø 0.5mm Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case-DIP: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 5 V Models: 15VDC max. 12V Models: 24VDC max. 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

• 24 Pin DIL Package
• Wide 2:1 Input Range
• 1500VDC Isolation
• Up to 3500VDC Isolation
• Continuous Short Circuit Protection
• Efficiency up to 82%
• Operating Temperature Range -40° ~ +85°C
• Plastic Case Standard , Optional Metal Case

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR2 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-0505S03AX 4.5-9 40 857 5 150 600 70 2200 RR2-0507S03AX 4.5-9 40 833 7.2 104 417 72 1000 RR2-0509S03AX 4.5-9 40 833 9 83 333 72 470 RR2-0512S03AX 4.5-9 40 810 12 63 250 74 470 RR2-0515S03AX 4.5-9 40 810 15 50 200 74 470 RR2-0518S03AX 4.5-9 40 810 18 42 167 74 220 RR2-0524S03AX 4.5-9 40 857 24 31 125 70 220 RR2-0505D03AX 4.5-9 40 869 ±5 ±75 ±300 69 ±1000 RR2-0507D03AX 4.5-9 40 896 ±7.2 ±52 ±208 67 ±220 RR2-0509D03AX 4.5-9 40 857 ±9 ±42 ±167 70 ±220 RR2-0512D03AX 4.5-9 40 833 ±12 ±31 ±125 72 ±220 RR2-0515D03AX 4.5-9 40 810 ±15 ±25 ±100 74 ±220 RR2-0518D03AX 4.5-9 40 810 ±18 ±21 ±83 74 ±220 RR2-0524D03AX 4.5-9 40 857 ±24 ±16 ±63 70 ±100 RR2-1205S03AX 9-18 20 328 5 150 600 76 2200 RR2-1207S03AX 9-18 20 338 7.2 104 417 74 1000 RR2-1209S03AX 9-18 20 324 9 83 333 77 470 RR2-1212S03AX 9-18 20 316 12 63 250 79 470 RR2-1215S03AX 9-18 20 316 15 50 200 79 470 RR2-1218S03AX 9-18 20 316 18 42 167 79 220 RR2-1224S03AX 9-18 20 316 24 31 125 79 220 RR2-1205D03AX 9-18 20 329 ±5 ±75 ±300 76 ±1000 RR2-1207D03AX 9-18 20 325 ±7.2 ±52 ±208 77 ±220 RR2-1209D03AX 9-18 20 325 ±9 ±42 ±167 77 ±220 RR2-1212D03AX 9-18 20 316 ±12 ±31 ±125 79 ±220 RR2-1215D03AX 9-18 20 316 ±15 ±25 ±100 79 ±220 RR2-1218D03AX 9-18 20 321 ±18 ±21 ±83 78 ±220 RR2-1224D03AX 9-18 20 316 ±24 ±16 ±63 79 ±100 RR2-2405S03AX 18-36 12 156 5 150 600 80 2200 RR2-2407S03AX 18-36 12 162 7.2 104 417 77 1000 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-0505S03AX 4.5-9 40 857 5 150 600 70 2200 RR2-0507S03AX 4.5-9 40 833 7.2 104 417 72 1000 RR2-0509S03AX 4.5-9 40 833 9 83 333 72 470 RR2-0512S03AX 4.5-9 40 810 12 63 250 74 470 RR2-0515S03AX 4.5-9 40 810 15 50 200 74 470 RR2-0518S03AX 4.5-9 40 810 18 42 167 74 220 RR2-0524S03AX 4.5-9 40 857 24 31 125 70 220 RR2-0505D03AX 4.5-9 40 869 ±5 ±75 ±300 69 ±1000 RR2-0507D03AX 4.5-9 40 896 ±7.2 ±52 ±208 67 ±220 RR2-0509D03AX 4.5-9 40 857 ±9 ±42 ±167 70 ±220 RR2-0512D03AX 4.5-9 40 833 ±12 ±31 ±125 72 ±220 RR2-0515D03AX 4.5-9 40 810 ±15 ±25 ±100 74 ±220 RR2-0518D03AX 4.5-9 40 810 ±18 ±21 ±83 74 ±220 RR2-0524D03AX 4.5-9 40 857 ±24 ±16 ±63 70 ±100 RR2-1205S03AX 9-18 20 328 5 150 600 76 2200 RR2-1207S03AX 9-18 20 338 7.2 104 417 74 1000 RR2-1209S03AX 9-18 20 324 9 83 333 77 470 RR2-1212S03AX 9-18 20 316 12 63 250 79 470 RR2-1215S03AX 9-18 20 316 15 50 200 79 470 RR2-1218S03AX 9-18 20 316 18 42 167 79 220 RR2-1224S03AX 9-18 20 316 24 31 125 79 220 RR2-1205D03AX 9-18 20 329 ±5 ±75 ±300 76 ±1000 RR2-1207D03AX 9-18 20 325 ±7.2 ±52 ±208 77 ±220 RR2-1209D03AX 9-18 20 325 ±9 ±42 ±167 77 ±220 RR2-1212D03AX 9-18 20 316 ±12 ±31 ±125 79 ±220 RR2-1215D03AX 9-18 20 316 ±15 ±25 ±100 79 ±220 RR2-1218D03AX 9-18 20 321 ±18 ±21 ±83 78 ±220 RR2-1224D03AX 9-18 20 316 ±24 ±16 ±63 79 ±100 RR2-2405S03AX 18-36 12 156 5 150 600 80 2200 RR2-2407S03AX 18-36 12 162 7.2 104 417 77 1000 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de NOTE 1. Typical value at nominal input voltage and full load. 2. Test by nominal input voltage and constant resistor load. 3. Measured Input reflected ripple current with a simulated source inductance of 12uH. 4. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. 7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. DC/DC-Converter RR2-S03/D03 3.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-2409S03AX 18-36 12 156 9 83 333 80 470 RR2-2412S03AX 18-36 12 152 12 62 250 82 470 RR2-2415S03AX 18-36 12 152 15 50 200 82 470 RR2-2418S03AX 18-36 12 158 18 42 167 79 220 RR2-2424S03AX 18-36 12 156 24 31 125 80 220 RR2-2405D03AX 18-36 12 156 ±5 ±75 ±300 80 ±1000 RR2-2407D03AX 18-36 12 160 ±7.2 ±52 ±208 78 ±220 RR2-2409D03AX 18-36 12 158 ±9 ±42 ±167 80 ±220 RR2-2412D03AX 18-36 12 152 ±12 ±31 ±125 82 ±220 RR2-2415D03AX 18-36 12 152 ±15 ±25 ±100 82 ±220 RR2-2418D03AX 18-36 12 156 ±18 ±21 ±83 80 ±220 RR2-2424D03AX 18-36 12 156 ±24 ±16 ±63 80 ±100 RR2-4805S03AX 36-72 8 81 5 150 600 77 2200 RR2-4807S03AX 36-72 8 80 7.2 104 417 78 1000 RR2-4809S03AX 36-72 8 80 9 83 333 78 470 RR2-4812S03AX 36-72 8 78 12 63 250 80 470 RR2-4815S03AX 36-72 8 78 15 50 200 80 470 RR2-4818S03AX 36-72 8 81 18 42 167 77 220 RR2-4824S03AX 36-72 8 78 24 31 125 80 220 RR2-4805D03AX 36-72 8 80 ±5 ±75 ±300 78 ±1000 RR2-4807D03AX 36-72 8 80 ±7.2 ±52 ±208 78 ±220 RR2-4809D03AX 36-72 8 79 ±9 ±42 ±167 79 ±220 RR2-4812D03AX 36-72 8 78 ±12 ±31 ±125 80 ±220 RR2-4815D03AX 36-72 8 78 ±15 ±25 ±100 80 ±220 RR2-4818D03AX 36-72 8 80 ±18 ±21 ±83 78 ±220 RR2-4824D03AX 36-72 8 78 ±24 ±15.8 ±63 80 ±100 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case TEST CONFIGURATIONS E C1 L C2 RR2-05XXS/D03AX 220uF/100V 12uH RR2-12XXS/D03AX 220uF/100V 12uH RR2-24XXS/D03AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D03AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RR2-2409S03AX 18-36 12 156 9 83 333 80 470 RR2-2412S03AX 18-36 12 152 12 62 250 82 470 RR2-2415S03AX 18-36 12 152 15 50 200 82 470 RR2-2418S03AX 18-36 12 158 18 42 167 79 220 RR2-2424S03AX 18-36 12 156 24 31 125 80 220 RR2-2405D03AX 18-36 12 156 ±5 ±75 ±300 80 ±1000 RR2-2407D03AX 18-36 12 160 ±7.2 ±52 ±208 78 ±220 RR2-2409D03AX 18-36 12 158 ±9 ±42 ±167 80 ±220 RR2-2412D03AX 18-36 12 152 ±12 ±31 ±125 82 ±220 RR2-2415D03AX 18-36 12 152 ±15 ±25 ±100 82 ±220 RR2-2418D03AX 18-36 12 156 ±18 ±21 ±83 80 ±220 RR2-2424D03AX 18-36 12 156 ±24 ±16 ±63 80 ±100 RR2-4805S03AX 36-72 8 81 5 150 600 77 2200 RR2-4807S03AX 36-72 8 80 7.2 104 417 78 1000 RR2-4809S03AX 36-72 8 80 9 83 333 78 470 RR2-4812S03AX 36-72 8 78 12 63 250 80 470 RR2-4815S03AX 36-72 8 78 15 50 200 80 470 RR2-4818S03AX 36-72 8 81 18 42 167 77 220 RR2-4824S03AX 36-72 8 78 24 31 125 80 220 RR2-4805D03AX 36-72 8 80 ±5 ±75 ±300 78 ±1000 RR2-4807D03AX 36-72 8 80 ±7.2 ±52 ±208 78 ±220 RR2-4809D03AX 36-72 8 79 ±9 ±42 ±167 79 ±220 RR2-4812D03AX 36-72 8 78 ±12 ±31 ±125 80 ±220 RR2-4815D03AX 36-72 8 78 ±15 ±25 ±100 80 ±220 RR2-4818D03AX 36-72 8 80 ±18 ±21 ±83 78 ±220 RR2-4824D03AX 36-72 8 78 ±24 ±15.8 ±63 80 ±100 Suffix “3”means 3.5KVdc isolation Suffix “M”means Metal Case instead of standard Plastic case TEST CONFIGURATIONS E C1 L C2 RR2-05XXS/D03AX 220uF/100V 12uH RR2-12XXS/D03AX 220uF/100V 12uH RR2-24XXS/D03AX 220uF/100V 12uH MLCC470pF RR2-48XXS/D03AX 220uF/100V 12uH MLCC470pF EMI FILTER Input Filter Components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These Components should be mounted as close as possible to the module, and all leads should be minimized to decrease radiated noise. DC/DC-Converter RR2-S03/D03 3.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RR2-XXXXS03A1 RR2-XXXXS03A1M RR2-XXXXS03A1 RR2-XXXXS03A1M DC/DC-Converter RR2-S03/D03 3.0W 2:1 Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28