RR1-1209D02A1

RR1-0503S02AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 OUTPUT SPECIFICATION Voltage accuracy: ±2% Line regulation: Single &Dual ±0.5% max. Load regulation: Single ( 0% to 100% ) : ±0.5%,max. Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 75mV pk-pk Temperature coefficient: ±0.02%°C Capacitor load: See table Transient Recovery Time: ±3% max. Transient Response: 3.3V Output ±5% max. INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1000 ~ 6000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Single 40kHz typ., Dual 250KHz typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material: Ø 0.5mm Alloy42 Solder-coated, Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 7VDC max

12V Models: 15VDC max 24V Models: 28VDC max Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR1-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 24 Pin DIL Package
• 1000VDC Isolation
• High Isolation up to 6000VDC (optional)
• Continuous Short Circuit Protection
• Efficiency up to 81%
• Operating Temperature Range -40° ~ +85°C
• Plastic Case Standard , Optional Metal Case RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR1 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0503S02AX 5 65 569 3.3 500 58 330 RR1-0505S02AX 5 42 588 5 400 68 330 RR1-0507S02AX 5 50 588 7.2 278 68 330 RR1-0509S02AX 5 55 571 9 222 70 330 RR1-0512S02AX 5 52 563 12 167 71 330 RR1-0515S02AX 5 55 588 15 133 68 330 RR1-0518S02AX 5 55 597 18 111 67 330 RR1-0524S02AX 5 95 606 24 83.3 66 330 RR1-1203S02AX 12 35 225 3.3 500 61 330 RR1-1205S02AX 12 20 256 5 400 65 330 RR1-1207S02AX 12 25 256 7.2 278 65 330 RR1-1209S02AX 12 31 238 9 222 70 330 RR1-1212S02AX 12 30 231 12 167 72 330 RR1-1215S02AX 12 35 238 15 133 70 330 RR1-1218S02AX 12 40 238 18 111 70 330 RR1-1224S02AX 12 40 235 24 83.3 71 330 RR1-2403S02AX 24 15 139 3.3 600 60 330 RR1-2405S02AX 24 15 121 5 400 69 330 RR1-2407S02AX 24 20 126 7.2 278 66 330 RR1-2409S02AX 24 25 128 9 222 65 330 RR1-2412S02AX 24 20 121 12 167 69 330 RR1-2415S02AX 24 20 121 15 133 69 330 RR1-2418S02AX 24 20 121 18 111 69 330 RR1-2424S02AX 24 20 116 24 83.3 72 330 RR1-0503D02AX 5 13 606 ±3.3 ±300 66 ±1000 RR1-0505D02AX 5 15 548 ±5 ±200 73 ±470 RR1-0507D02AX 5 20 548 ±7.2 ±278 73 ±470 RR1-0509D02AX 5 60 526 ±9 ±111 76 ±470 RR1-0512D02AX 5 20 563 ±12 ±83.3 71 ±470 RR1-0515D02AX 5 25 556 ±15 ±67 72 ±470 RR1-0518D02AX 5 42 556 ±18 ±111 72 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg- electronic.de DC/DC-Converter RR1-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D02AX 5 40 556 ±24 ±42 72 ±220 RR1-1203D02AX 12 6 231 ±3.3 ±300 72 ±1000 RR1-1205D02AX 12 7 219 ±5 ±200 76 ±470 RR1-1207D02AX 12 10 222 ±7.2 ±278 75 ±470 RR1-1209D02AX 12 10 208 ±9 ±111 80 ±470 RR1-1212D02AX 12 12 208 ±12 ±83.3 80 ±470 RR1-1215D02AX 12 15 208 ±15 ±67 80 ±470 RR1-1218D02AX 12 20 222 ±18 ±111 75 ±220 RR1-1224D02AX 12 20 216 ±24 ±42 77 ±220 RR1-2403D02AX 24 5 114 ±3.3 ±300 73 ±1000 RR1-2405D02AX 24 5 107 ±5 ±200 78 ±470 RR1-2407D02AX 24 6 104 ±7.2 ±278 80 ±470 RR1-2409D02AX 24 6 103 ±9 ±111 81 ±470 RR1-2412D02AX 24 6 103 ±12 ±83.3 81 ±470 RR1-2415D02AX 24 10 107 ±15 ±67 78 ±470 RR1-2418D02AX 24 10 110 ±18 ±111 76 ±220 RR1-2424D02AX 24 15 107 ±24 ±42 78 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS02AX 220uF/100V 12uH 220uF/100V RR1-12XXS02AX 220uF/100V 12uH 220uF/100V RR1-24XXS02AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD02AX 220uF/100V 12uH RR1-12XXD02AX 220uF/100V 12uH RR1-24XXD02AX 220uF/100V 12uH DUAL OUTPUT +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D02AX 5 40 556 ±24 ±42 72 ±220 RR1-1203D02AX 12 6 231 ±3.3 ±300 72 ±1000 RR1-1205D02AX 12 7 219 ±5 ±200 76 ±470 RR1-1207D02AX 12 10 222 ±7.2 ±278 75 ±470 RR1-1209D02AX 12 10 208 ±9 ±111 80 ±470 RR1-1212D02AX 12 12 208 ±12 ±83.3 80 ±470 RR1-1215D02AX 12 15 208 ±15 ±67 80 ±470 RR1-1218D02AX 12 20 222 ±18 ±111 75 ±220 RR1-1224D02AX 12 20 216 ±24 ±42 77 ±220 RR1-2403D02AX 24 5 114 ±3.3 ±300 73 ±1000 RR1-2405D02AX 24 5 107 ±5 ±200 78 ±470 RR1-2407D02AX 24 6 104 ±7.2 ±278 80 ±470 RR1-2409D02AX 24 6 103 ±9 ±111 81 ±470 RR1-2412D02AX 24 6 103 ±12 ±83.3 81 ±470 RR1-2415D02AX 24 10 107 ±15 ±67 78 ±470 RR1-2418D02AX 24 10 110 ±18 ±111 76 ±220 RR1-2424D02AX 24 15 107 ±24 ±42 78 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS02AX 220uF/100V 12uH 220uF/100V RR1-12XXS02AX 220uF/100V 12uH 220uF/100V RR1-24XXS02AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD02AX 220uF/100V 12uH RR1-12XXD02AX 220uF/100V 12uH RR1-24XXD02AX 220uF/100V 12uH DUAL OUTPUT +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D02AX 5 40 556 ±24 ±42 72 ±220 RR1-1203D02AX 12 6 231 ±3.3 ±300 72 ±1000 RR1-1205D02AX 12 7 219 ±5 ±200 76 ±470 RR1-1207D02AX 12 10 222 ±7.2 ±278 75 ±470 RR1-1209D02AX 12 10 208 ±9 ±111 80 ±470 RR1-1212D02AX 12 12 208 ±12 ±83.3 80 ±470 RR1-1215D02AX 12 15 208 ±15 ±67 80 ±470 RR1-1218D02AX 12 20 222 ±18 ±111 75 ±220 RR1-1224D02AX 12 20 216 ±24 ±42 77 ±220 RR1-2403D02AX 24 5 114 ±3.3 ±300 73 ±1000 RR1-2405D02AX 24 5 107 ±5 ±200 78 ±470 RR1-2407D02AX 24 6 104 ±7.2 ±278 80 ±470 RR1-2409D02AX 24 6 103 ±9 ±111 81 ±470 RR1-2412D02AX 24 6 103 ±12 ±83.3 81 ±470 RR1-2415D02AX 24 10 107 ±15 ±67 78 ±470 RR1-2418D02AX 24 10 110 ±18 ±111 76 ±220 RR1-2424D02AX 24 15 107 ±24 ±42 78 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS02AX 220uF/100V 12uH 220uF/100V RR1-12XXS02AX 220uF/100V 12uH 220uF/100V RR1-24XXS02AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD02AX 220uF/100V 12uH RR1-12XXD02AX 220uF/100V 12uH RR1-24XXD02AX 220uF/100V 12uH DUAL OUTPUT DC/DC-Converter RR1-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RR1-XXXXS02A1 RR1-XXXXS02A1M DC/DC-Converter RR1-S02/D02 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28