RR1-1203S01A1

RR1-0503S01AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 OUTPUT SPECIFICATION Voltage accuracy: ±2% Line regulation: Single &Dual ±0.5% max. Load regulation: Single ( 0% to 100% ) : ±0.5%,max. Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 75mV pk-pk max. Temperature coefficient: ±0.02% °C Capacitor load: See table Transient Recovery Time: ±3% max. Transient Response: 3.3V Output ±5% max. INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3sec.): 1000 ~ 6000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Single 40kHz typ., Dual 350KHz typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material: Ø 0.5mm Alloy42 Solder-coated, Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 7VDC max

12V Models: 15VDC max 24V Models: 28VDC max Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR1-S01/D01 1.5W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 24 Pin DIL Package
• 1000VDC Isolation
• High Isolation up to 6000VDC Isolation (optional)
• Continuous Short Circuit Protection
• Efficiency up to 79%
• Operating Temperature Range -40° ~ +85°C
• Plastic Case Standard , Optional Metal Case RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR1 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0503S01AX 5 50 426 3.3 400 62 220 RR1-0505S01AX 5 42 448 5 300 67 220 RR1-0507S01AX 5 50 462 7.2 208 65 220 RR1-0509S01AX 5 65 462 9 167 65 220 RR1-0512S01AX 5 50 429 12 125 70 220 RR1-0515S01AX 5 65 441 15 100 68 220 RR1-0518S01AX 5 60 448 18 83 67 220 RR1-0524S01AX 5 60 448 24 63 67 220 RR1-1203S01AX 12 50 177 3.3 400 62 220 RR1-1205S01AX 12 25 187 5 300 67 220 RR1-1207S01AX 12 50 189 7.2 208 66 220 RR1-1209S01AX 12 40 192 9 167 65 220 RR1-1212S01AX 12 26 179 12 125 70 220 RR1-1215S01AX 12 40 195 15 100 64 220 RR1-1218S01AX 12 45 198 18 83 63 220 RR1-1224S01AX 12 40 202 24 63 62 220 RR1-2403S01AX 24 35 104 3.3 400 53 220 RR1-2405S01AX 24 20 98 5 300 64 220 RR1-2407S01AX 24 35 98 7.2 208 64 220 RR1-2409S01AX 24 35 98 9 167 64 220 RR1-2412S01AX 24 16 93 12 125 67 220 RR1-2415S01AX 24 40 95 15 100 66 220 RR1-2418S01AX 24 40 96 18 83 65 220 RR1-2424S01AX 24 40 96 24 63 65 220 RR1-0503D01AX 5 15 377 ±3.3 ±200 70 ±1000 RR1-0505D01AX 5 40 417 ±5 ±150 72 ±470 RR1-0507D01AX 5 35 429 ±7.2 ±208 70 ±470 RR1-0509D01AX 5 20 429 ±9 ±83 70 ±470 RR1-0512D01AX 5 25 423 ±12 ±63 71 ±470 RR1-0515D01AX 5 30 423 ±15 ±50 71 ±470 RR1-0518D01AX 5 30 429 ±18 ±83 70 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@ rsg-electronic.de DC/DC-Converter RR1-S01/D01 1.5W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D01AX 5 35 435 ±24 ±31.5 69 ±220 RR1-1203D01AX 12 15 147 ±3.3 ±200 75 ±1000 RR1-1205D01AX 12 6 162 ±5 ±150 77 ±470 RR1-1207D01AX 12 8 167 ±7.2 ±208 75 ±470 RR1-1209D01AX 12 10 158 ±9 ±83 79 ±470 RR1-1212D01AX 12 24 164 ±12 ±63 76 ±470 RR1-1215D01AX 12 20 169 ±15 ±50 74 ±470 RR1-1218D01AX 12 20 169 ±18 ±83 74 ±220 RR1-1224D01AX 12 20 164 ±24 ±31.5 76 ±220 RR1-2403D01AX 24 8 76 ±3.3 ±200 72 ±1000 RR1-2405D01AX 24 5 83 ±5 ±150 75 ±470 RR1-2407D01AX 24 8 83 ±7.2 ±208 75 ±470 RR1-2409D01AX 24 10 82 ±9 ±83 76 ±470 RR1-2412D01AX 24 10 81 ±12 ±63 77 ±470 RR1-2415D01AX 24 10 82 ±15 ±50 76 ±470 RR1-2418D01AX 24 13 89 ±18 ±83 70 ±220 RR1-2424D01AX 24 16 87 ±24 ±31.5 72 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS01AX 220uF/100V 12uH 220uF/100V RR1-12XXS01AX 220uF/100V 12uH 220uF/100V RR1-24XXS01AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD01AX 220uF/100V 12uH RR1-12XXD01AX 220uF/100V 12uH RR1-24XXD01AX 220uF/100V 12uH DUAL OUTPUT +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D01AX 5 35 435 ±24 ±31.5 69 ±220 RR1-1203D01AX 12 15 147 ±3.3 ±200 75 ±1000 RR1-1205D01AX 12 6 162 ±5 ±150 77 ±470 RR1-1207D01AX 12 8 167 ±7.2 ±208 75 ±470 RR1-1209D01AX 12 10 158 ±9 ±83 79 ±470 RR1-1212D01AX 12 24 164 ±12 ±63 76 ±470 RR1-1215D01AX 12 20 169 ±15 ±50 74 ±470 RR1-1218D01AX 12 20 169 ±18 ±83 74 ±220 RR1-1224D01AX 12 20 164 ±24 ±31.5 76 ±220 RR1-2403D01AX 24 8 76 ±3.3 ±200 72 ±1000 RR1-2405D01AX 24 5 83 ±5 ±150 75 ±470 RR1-2407D01AX 24 8 83 ±7.2 ±208 75 ±470 RR1-2409D01AX 24 10 82 ±9 ±83 76 ±470 RR1-2412D01AX 24 10 81 ±12 ±63 77 ±470 RR1-2415D01AX 24 10 82 ±15 ±50 76 ±470 RR1-2418D01AX 24 13 89 ±18 ±83 70 ±220 RR1-2424D01AX 24 16 87 ±24 ±31.5 72 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS01AX 220uF/100V 12uH 220uF/100V RR1-12XXS01AX 220uF/100V 12uH 220uF/100V RR1-24XXS01AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD01AX 220uF/100V 12uH RR1-12XXD01AX 220uF/100V 12uH RR1-24XXD01AX 220uF/100V 12uH DUAL OUTPUT +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout TEST CONFIGURATIONS EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RR1-0524D01AX 5 35 435 ±24 ±31.5 69 ±220 RR1-1203D01AX 12 15 147 ±3.3 ±200 75 ±1000 RR1-1205D01AX 12 6 162 ±5 ±150 77 ±470 RR1-1207D01AX 12 8 167 ±7.2 ±208 75 ±470 RR1-1209D01AX 12 10 158 ±9 ±83 79 ±470 RR1-1212D01AX 12 24 164 ±12 ±63 76 ±470 RR1-1215D01AX 12 20 169 ±15 ±50 74 ±470 RR1-1218D01AX 12 20 169 ±18 ±83 74 ±220 RR1-1224D01AX 12 20 164 ±24 ±31.5 76 ±220 RR1-2403D01AX 24 8 76 ±3.3 ±200 72 ±1000 RR1-2405D01AX 24 5 83 ±5 ±150 75 ±470 RR1-2407D01AX 24 8 83 ±7.2 ±208 75 ±470 RR1-2409D01AX 24 10 82 ±9 ±83 76 ±470 RR1-2412D01AX 24 10 81 ±12 ±63 77 ±470 RR1-2415D01AX 24 10 82 ±15 ±50 76 ±470 RR1-2418D01AX 24 13 89 ±18 ±83 70 ±220 RR1-2424D01AX 24 16 87 ±24 ±31.5 72 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V . C1 L C2 RR1-05XXS01AX 220uF/100V 12uH 220uF/100V RR1-12XXS01AX 220uF/100V 12uH 220uF/100V RR1-24XXS01AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD01AX 220uF/100V 12uH RR1-12XXD01AX 220uF/100V 12uH RR1-24XXD01AX 220uF/100V 12uH DUAL OUTPUT DC/DC-Converter RR1-S01/D01 1.5W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RR1-XXXXS01A1 RR1-XXXXS01A1M DC/DC-Converter RR1-S01/D01 1.5W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28