RR1-0515S03A1

RR1-0503S03AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RR1-S03/D03 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 24 Pin DIL Package
• 1000VDC Isolation
• High Isolation up to 6000VDC (optional)
• Continuous Short Circuit Protection
• Efficiency up to 83%
• Operating Temperature Range -40° ~ +85°C
• Plastic Case Standard , Optional Metal Case OUTPUT SPECIFICATION Voltage accuracy: ±2% Line regulation: Single &Dual ±0.5% max. Load regulation: Single ( 0% to 100% ) : ±1%,max. Short Circuit Protection : Indefinite (Automatic Recovery) Ripple noise (20Mhz bandwidth): 75mV pk-pk max. Temperature coefficient: ±0.02% °C Capacitor load: See table Transient Recovery Time: ±3% max. Transient Response: 3.3V Output ±5% max. INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: PI Type Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage Metal Case (3 sec.): 1000VDC I/O Isolation Voltage (3 sec.): 1000 ~ 6000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Single 40kHz typ., Dual 250KHz typ. Humidity: 95% rel H Reliability Calculated MTBF : > 1.00MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material: Ø 0.5mm Alloy42 Solder-coated, Brass Solder coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 12.5 (plastic), 15.0g ( Metal) Dimmension DIP: 1.25“ x 0.8“ x 0.4“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 7VDC max

12V Models: 15VDC max 24V Models: 28VDC max Soldering Temperature: 260°C max. EMC SPECIFICATIONS (2) Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RR1 - XX XX S/D XX Power (W) Input Type A X X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current VoltageRange No-Load Full Load Voltage Full load EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RR1-0503S03AX 5 62 683 3.3 600 58 470 RR1-0505S03AX 5 65 909 5 600 66 470 RR1-0507S03AX 5 65 923 7.2 417 65 470 RR1-0509S03AX 5 70 882 9 333 68 470 RR1-0512S03AX 5 60 845 12 250 71 470 RR1-0515S03AX 5 70 833 15 200 72 470 RR1-0518S03AX 5 70 857 18 167 70 470 RR1-0524S03AX 5 100 896 24 125 67 470 RR1-1203S03AX 12 30 232 3.3 600 71 470 RR1-1205S03AX 12 36 253 5 600 66 470 RR1-1207S03AX 12 32 235 7.2 417 71 470 RR1-1209S03AX 12 32 235 9 333 71 470 RR1-1212S03AX 12 37 231 12 250 72 470 RR1-1215S03AX 12 35 225 15 200 74 470 RR1-1218S03AX 12 35 222 18 167 75 470 RR1-1224S03AX 12 55 235 24 125 71 470 RR1-2403S03AX 24 10 158 3.3 700 61 470 RR1-2405S03AX 24 23 187 5 600 67 470 RR1-2407S03AX 24 25 189 7.2 417 66 470 RR1-2409S03AX 24 27 184 9 333 68 470 RR1-2412S03AX 24 30 181 12 250 69 470 RR1-2415S03AX 24 28 179 15 200 70 470 RR1-2418S03AX 24 16 169 18 167 74 470 RR1-2424S03AX 24 20 167 24 125 75 470 RR1-0503D03AX 5 15 776 ±3.3 ±400 68 ±1000 RR1-0505D03AX 5 20 845 ±5 ±300 71 ±470 RR1-0507D03AX 5 20 811 ±7.2 ±417 74 ±470 RR1-0509D03AX 5 25 789 ±9 ±167 76 ±470 RR1-0512D03AX 5 40 822 ±12 ±125 73 ±470 RR1-0515D03AX 5 30 811 ±15 ±100 74 ±470 RR1 -0518D03AX 5 45 822 ±18 ±167 73 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to :info@rsg-electronic.de DC/DC-Converter RR1-S03/D03 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current VoltageRange No-Load Full Load Voltage Full load EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RR1-0524D03AX 5 45 800 ±24 ±62.5 75 ±220 RR1 -1203D03AX 12 7 306 ±3.3 ±400 72 ±1000 RR1-1205D03AX 12 8 321 ±5 ±300 78 ±1000 RR1 -1207D03AX 12 8 313 ±7.2 ±417 80 ±470 RR1-1209D03AX 12 10 313 ±9 ±167 80 ±470 RR1-1212D03AX 12 10 321 ±12 ±125 78 ±470 RR1-1215D03AX 12 15 309 ±15 ±100 81 ±470 RR1-1218D03AX 12 15 309 ±18 ±167 81 ±220 RR1-1224D03AX 12 20 316 ±24 ±62.5 79 ±220 RR1 -2403D03AX 24 5 174 ±3.3 ±455 72 ±1000 RR1-2405D03AX 24 6 158 ±5 ±300 79 ±470 RR1 -2407D03AX 24 5 158 ±7.2 ±417 79 ±470 RR1-2409D03AX 24 7 152 ±9 ±167 82 ±470 RR1-2412D03AX 24 8 151 ±12 ±125 83 ±470 RR1-2415D03AX 24 10 154 ±15 ±100 81 ±470 RR1-2418D03AX 24 15 156 ±18 ±167 80 ±220 RR1-2424D03AX 24 15 154 ±24 ±62.5 81 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR1-05XXS03AX 220uF/100V 12uH 220uF/100V RR1-12XXS03AX 220uF/100V 12uH 220uF/100V RR1-24XXS03AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD03AX 220uF/100V 12uH RR1-12XXD03AX 220uF/100V 12uH RR1-24XXD03AX 220uF/100V 12uH DUAL OUTPUT +Vin +Vout DC/DC Converter -Vin -Vout +Vin +Vout DC/DC Converter -Vin -Vout EMI Filter Input filter components (C1,C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L L Load Load C1 C2 C1 Single Output Dual Output MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current VoltageRange No-Load Full Load Voltage Full load EFFICIENCY Capacitor (Vdc) (mA) (mA) (Vdc) (mA) @FL(%) Load(uF) RR1-0524D03AX 5 45 800 ±24 ±62.5 75 ±220 RR1 -1203D03AX 12 7 306 ±3.3 ±400 72 ±1000 RR1-1205D03AX 12 8 321 ±5 ±300 78 ±1000 RR1 -1207D03AX 12 8 313 ±7.2 ±417 80 ±470 RR1-1209D03AX 12 10 313 ±9 ±167 80 ±470 RR1-1212D03AX 12 10 321 ±12 ±125 78 ±470 RR1-1215D03AX 12 15 309 ±15 ±100 81 ±470 RR1-1218D03AX 12 15 309 ±18 ±167 81 ±220 RR1-1224D03AX 12 20 316 ±24 ±62.5 79 ±220 RR1 -2403D03AX 24 5 174 ±3.3 ±455 72 ±1000 RR1-2405D03AX 24 6 158 ±5 ±300 79 ±470 RR1 -2407D03AX 24 5 158 ±7.2 ±417 79 ±470 RR1-2409D03AX 24 7 152 ±9 ±167 82 ±470 RR1-2412D03AX 24 8 151 ±12 ±125 83 ±470 RR1-2415D03AX 24 10 154 ±15 ±100 81 ±470 RR1-2418D03AX 24 15 156 ±18 ±167 80 ±220 RR1-2424D03AX 24 15 154 ±24 ±62.5 81 ±220 Suffix “3”means 3KVdc isolation Suffix “5”means 5.2KVdc isolation Suffix “6”means 6KVdc isolation Suffix “M”means Metal Case Up To 3KVdc isolation 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ) 4.Measured Input reflected ripple current with a simulated source inductance of 12uH. 5.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 7.Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 8.An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000 -4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L C2 RR1-05XXS03AX 220uF/100V 12uH 220uF/100V RR1-12XXS03AX 220uF/100V 12uH 220uF/100V RR1-24XXS03AX 220uF/100V 12uH 220uF/100V SINGEL OUTPUT C1 L RR1-05XXD03AX 220uF/100V 12uH RR1-12XXD03AX 220uF/100V 12uH RR1-24XXD03AX 220uF/100V 12uH DUAL OUTPUT DC/DC-Converter RR1-S03/D03 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RR1-XXXXS03A1 RR1-XXXXS03A1M DC/DC-Converter RR1-S03/D03 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28