RM5532 FAIRCHILD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 12

Technical content

Features

  • Small signal bandwidth – 10 MHz
  • Output drive capability – 600W, 10 VRMS
  • Input noise voltage – 5 nV/
  • DC voltage gain – 50,000
  • AC voltage gain – 2200 at 10 KHz
  • Power bandwidth – 140 KHz
  • Slew rate – 8 V/mS
  • Large supply voltage range – ±3V to ±20V

Description

The RC5532 is a high performance, dual low noise opera- tional amplifier. Compared to standard dual operational amplifiers, such as the RC747, it shows better noise perfor- mance, improved output drive capability, and considerably higher small-signal and power bandwidths. This makes the device especially suitable for application in high quality and professional audio equipment, instrumenta- tion, control circuits, and telephone channel amplifiers. The op amp is internally compensated for gains equal to one. If very low noise is of prime importance, it is recommended that the RC5532A version be used which has guaranteed noise specifications. Hz RC5532/RC5532A High Performance Dual Low Noise Operational Amplifier Rev. 1.1.2 Block Diagram A B 65-5532-01 Output A –Input A +Input A –VS +V S Output B –Input B +Input B

RC5532/RC5532A PRODUCT SPECIFICATION Pin Assignments Absolute Maximum Ratings (beyond which the device may be damaged)1 Notes: 1. Functional operation under any of these conditions is NOT implied. 2. For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage. 3. Short circuit to ground on one amplifier only. Operating Conditions Parameter Min. Typ. Max. Units Supply Voltage ±22 V Input Voltage ±VS V Differential Input Voltage 0.5 V PD TA < 50°C PDIP 468 mW CerDIP 833 SOIC 658 Junction Temperature PDIP 125 °C CerDIP, TO-99 175 Storage Temperature -65 150 °C Operating Temperature RM5532/A -55 125 °C RC5532/A 0 70 Lead Soldering Temperature (10 sec) 300 °C Parameter Min. Typ. Max. Units qJC Thermal resistance CerDIP 45 °C/W TO-99 50 qJA Thermal resistance PDIP 160 °C/W CerDIP 150 TO-99 190 For TA > 50°C Derate at PDIP 6.25 mW/ °C CerDIP 8.33 TO-99 5.26 65-5532-02 Output (A) –Input (A) +Input (A) Output (B) –Input (B) +Input (B) –VS +V S Output (A) –Input (A) +Input (A) –VS +V S Output (B) –Input (B) +Input (B) 65-5532-03

PRODUCT SPECIFICATION RC5532/RC5532A (VS = ±15V and TA = +25˚C unless otherwise noted) Notes: 1. Diodes protect the inputs against over-voltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential input voltage exceeds 0.6V. Maximum input current should be limited to ±10mA. 2. Over Temperature: RM = 55 °C £ TA £ 125°C; RC = 0°C £ TA £70°C

Electrical Characteristics

(VS = ±15V and TA = +25°C ) RM5532/5532A RC5532/5532A Input Offset Voltage 0.5 2.0 0.5 4.0 mV Over Temperature 3.0 5.0 mV Input Offset Current 100 10 150 nA Over Temperature 200 200 nA Input Bias Current 200 400 200 800 nA Over Temperature 700 1000 nA Supply Current 6.0 11 6.0 16 mA Over Temperature 13 22 mA Input Voltage Range ±12 ±13 ±12 ±13 V Common Mode Rejection Ratio 80 100 70 100 dB Power Supply Rejection Ratio 86 100 80 100 dB Large Signal Voltage Gain R L ³ 2 KW, VOUT = ±10V 50 25 100 V/mV Over Temperature 25 15 50 R L ³ 600W, VOUT = ±10V 40 15 50 Over Temperature 20 10 Output Voltage Swing R L ³ 600W ±12 ±13 ±12 ±13 V R L = 600W, VS = ±18V ±15 ±16 ±15 ±16 R L ³ 2kW ±12 ±13 Input Resistance (Diff. Mode) 300 300 KW Short Circuit Current 38 38 mA RC/RM5532 RC/RM5532A Input Noise Voltage DensityFO = 30 Hz 8.0 8.0 12 nV/ ÖHzFO = 1 kHz 5.0 5.0 6.0 Input Noise Current DensityFO = 30 Hz 2.7 2.7 pA/ ÖHzFO = 1 kHz 0.7 0.7 Channel Separation F = 1 kHz, RS = 5 kW 110 110 dB

Figure 1. Closed Loop Frequency Response Figure 2. Follower, Transient Response

PRODUCT SPECIFICATION RC5532/RC5532A Notes:

RC5532/RC5532A PRODUCT SPECIFICATION Notes:

PRODUCT SPECIFICATION RC5532/RC5532A Mec hanical Dimensions 8-Lead Ceramic DIP Package 5 8 A — .200 — 5.08 Symbol Inches Min. Max. Min. Max. Millimeters Notes b1 .014 .023 .36 .58 .065 1.65b2 .045 1.14 c1 .008 .015 .20 .38 E .220 .310 5.59 7.87 e .100 BSC 2.54 BSC L .125 .200 3.18 5.08 .015 .060 .38 1.52 .005 — .13 — 2, 8 5, 9 eA .300 BSC 7.62 BSC 7 Q 90¡ 105¡ 90¡ 105¡a D — .405 — 10.29 Notes: Index area: a notch or a pin one identification mark shall be located adjacent to pin one. The manufacturer's identification shall not be used as pin one identification mark. The minimum limit for dimension "b2" may be .023 (.58mm) for leads number 1, 4, 5 and 8 only. Dimension "Q" shall be measured from the seating plane to the base plane. This dimension allows for off-center lid, meniscus and glass overrun. The basic pin spacing is .100 (2.54mm) between centerlines. Each pin centerline shall be located within ±.010 (.25mm) of its exact longitudinal position relative to pins 1 and 8. Applies to all four corners (leads number 1, 4, 5, and 8). "eA" shall be measured at the center of the lead bends or at the centerline of the leads when "a" is 90¡. All leads – Increase maximum limit by .003 (.08mm) measured at the center of the flat, when lead finish applied. Six spaces. Note 1 D E Q A e L eA c1a

RC5532/RC5532A PRODUCT SPECIFICATION Mec hanical Dimensions (continued) 8-Lead Plastic DIP Package A — .210 — 5.33 Symbol Inches Min. Max. Min. Max. Millimeters Notes A1 .015 — .38 — .022 .56B .014 .36 B1 .045 .070 1.14 1.78 D .348 .430 8.84 10.92 .300 .325 7.62 8.26 .240 .280 6.10 7.11 E e — .430 — 10.92 .005 — .13 — A2 .115 .195 2.93 4.95 .100 BSC 2.54 BSC eB .115 .160 2.92 4.06L 8¡ 8¡ 5N C .008 .015 .20 .38 Notes: Dimensioning and tolerancing per ANSI Y14.5M-1982. "D" and "E1" do not include mold flashing. Mold flash or protrusions shall not exceed .010 inch (0.25mm). Terminal numbers are for reference only. "C" dimension does not include solder finish thickness. Symbol "N" is the maximum number of terminals. D e B A L 5 8 E eB C

PRODUCT SPECIFICATION RC5532/RC5532A Mec hanical Dimensions (continued) 8-Lead Metal Can IC Header Package k e a REFERENCE PLANE øb øb1 øD2 øD øD1 AQ FL1 L BASE and SEATING PLANE Notes: (All leads) øb applies between L1 & L2. øb1 applies between L2 & .500 (12.70mm) from the reference plane. Diameter is uncontrolled in L1 & beyond .500 (12.70mm) from the reference plane. Measured from the maximum diameter of the product. Leads having a maximum diameter .019 (.48mm) measured in below the reference plane of the product shall be within .007 (.18mm) of their true position relative to a maximum width tab. The product may be measured by direct methods or by gauge. All leads – increase maximum limit by .003 (.08mm) when lead finish is applied. A .165 .185 4.19 4.70 Symbol Inches Min. Max. Min. Max. Millimeters Notes øb .016 .019 .41 .48 .021 .53øb1 .016 .41 øD .335 .375 8.51 9.52 øD1 .305 .335 7.75 8.51 øD2 .110 .160 2.79 4.06 .200 BSC 5.08 BSCe .100 BSC 2.54 BSC 45¡ BSC 45¡ BSC F — .040 — 1.02 .027 .034 .69 .86 .027 .045 .69 1.14 2 1, 5 1, 5 a k L .500 .750 12.70 19.05 — .050 — 1.27 .250 — 6.35 — 1 .010 .045 .25 1.14Q

RC5532/RC5532A PRODUCT SPECIFICATION 2/98 0.0m Stock#DS30005532 Ó 1998 Fairchild Semiconductor Corporation LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonable expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com Fairchild Semiconductor Corporation Americas Customer Response Center Tel:1-888-522-5372 Fairchild Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 8 141-35-0 English Tel: +44 (0) 1 793-85-68-56 Italy Tel: +39 (0) 2 57 5631 Fairchild Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Center, 5 Canto Rd. Tsimshatsui, Kowloon Hong Kong Tel:+852 2737-7200 Fax:+852 2314-0061 National Semiconductor Japan Ltd. Tel:81-3-5620-6175 Fax:81-3-5620-6179

Ordering Information

Note: Product Number Temperature Range Screening Package RC5532D/RC5532AD 0°C to +70°C Commercial 8 Pin Ceramic DIP RC5532N/RC5532AN 0°C to +70°C Commercial 8 Pin Plastic DIP RM5532D/RM5532AD -55°C to +125°C Commercial 8 Pin Ceramic DIP RM5532D/883B -55°C to +125°C Military 8 Pin Ceramic DIP RM5532AD/883B -55°C to +125°C Military 8 Pin Ceramic DIP RM5532T/RM5532AT -55°C to +125°C Commercial 8 Pin TO-99 Metal Can RM5532T/883B -55°C to +125°C Military 8 Pin TO-99 Metal Can RM5532AT/883B -55°C to +125°C Military 8 Pin TO-99 Metal Can