DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

■ Typical Specifications （Potentiometer） Items RKJXK RKJXV Rated power 0.0125W Maximum operating voltage 50V AC, 5V DC Operating angle 60° ±6° 23° max. in each direction ※ Operating force 8mN ・ m max. （Not lever return type） 6±4mN ・ m （Lever return type） 14±10mN ・ m Operating life 100,000 cycles 2,000,000 cycles ■ Typical Specifications （Center-push） Items RKJXK RKJXV Ratings（max.） 50mA 12V DC Operating force 5.2±2.6N 7.4±3N Travel 0.5 mm 0.4 mm Operating life 100,000 cycles 500,000 cycles ＋0.5 −0.4 ＋0.5 −0.3 Refer to P.442 for soldering conditions. ThumbPointerTM （Stick Controller）RKJXK RKJXV Compact size, standard type. Also available with lever return mechanism Packing Specifications Tray Product No. Number of packages （pcs.） Export package measurements （mm）1 case / Japan 1 case / export packing RKJXK 500 1 ,000 373×540×225 RKJXV 1,6 0 0 1,6 0 0 540×360×250 Product Line Product No. Lever return mechanism Center-push Total resistance （kΩ） Resistance taper Minimum order unit （pcs.） Drawing No.Japan Export RKJXK122400Y With With

10 B（ 0 B ）

500 1 ,000 RKJXK122000D Without 2 RKJXK1210002 Without RKJXV1224005 With With 1,6 0 0 1,6 0 0 RKJXV1220001 Without 4 Note ※ If the lever is tilted more than 23° from the vertical position, operating feel irregularities or return mechanism errors may occur. Therefore, please do not tilt more than 23° .

15.5 3.1 13.3 7.7 8.254.5 6-ø1 hole 5-ø2.6 4-ø1.5 hole 4-1.35 1 Square hole Prohibited wiring area All directions Return position3.7 60˚ 19.3 22.7 20.7 12.9 ø7.916 X X YY 20.7 16Y ø7.9X 25.4 X Y3.7 60˚ 12.9 19.3 4-ø2.6 3.113.3 215.5 4-ø1.5 holes 6-ø1 holes Prohibited wiring area 2.2 4- Ø 2.6 Ø 3.5 Ø 4 4- Ø 1.2 hole 4.5 Ø 1.5 hole 12.65 8.73 8.73 6- Ø 1 hole 6.5 2- Ø 1.6 hole 8.6 d c a b ① ② ③ Prohibited wiring area Height of boss 13.15 13.15 17.79 21.28 VR2VR2 VR1 b c d SW1 a ① ② 46° max. 11.2 2.5 2.610.8 12.45 18.95 2.9 0.75 Height to top frame Lever return position any directionAny direction Dimention of VR RKJXK1210 RKJXK1220 RKJXK1224 RKJXV1224 ThumbPointerTM （Stick Controller）RKJXK RKJXV Dimensions Unit:mm No. Photo Style PC board mounting hole dimensions （Viewed from mounting side）

2.22.2 4-φ2.6 4-φ2.6 φ3.5φ3.5 Ø4Ø4 1010 φ1.5 holeφ1.5 hole 12.6512.65 8.738.73 6-φ1 hole6-φ1 hole ①①②②③③ 2-φ1.6 hole 2-φ1.6 hole 8.68.6 8.738.73 B 13.15 17.5 VR2 VR1 b c d SW1 a 46° max. 11.2 0.75 2.6 18.95 12.45 2.9 Dimention of VR Height to top frame Lever return position Any direction Height of boss （10.8） 13.15 RKJXV1220 Dimensions Unit:mm No. Photo Style PC board mounting hole dimensions （Viewed from mounting side） RKJXK/RKJXV／ThumbPointerTM （Stick Controller）

Type Variable resistor type Series RKJXK RKJXV RKJXY RKJXU Photo Dimensions （typical value） （mm） W 20.7 17.8 19.6 18.6 D 25.4 21.3 18.1 24.3 H 12.9 11. 2 4.9 5.2 Number ofoperating shafts Single-shaft Shaft material Metal Resin Directional resolution Continuous Directional operating feeling （tactile feeling） Without Lever return mechanism With / Without With Center-push switch With / Without Without Encoder Without Operating temperature range − 10℃ to ＋ 70℃ Operating life Directional operation 100,000 cycles 2,000,000 cycles 1 ,000,000 cycles 2,000,000 cycles Center-push 100,000 cycles 500,000 cycles ー ー Automotive use ー ー ー ー Life cycle (availability) Electrical performance Insulation resistance 100MΩ min. 250V DC ー ー Voltage proof 250V AC for 1 minute ー ー Slider noise 300mV p-p max. by JIS method Mechanical performance Directional operating force 8mN ・ m max. Without Lever return mechanism 6±4mN ・ m With Lever return mechanism 14±10 m N･m 0.43±0.25N 0.73±0.3N Push operating force 5.2±2.6N 7.4±3N ー ー Lever return precision ±5° ±0.1mm Actuator strength Push / pull Operating direction 0.3N･m ー 50N Environmental performance Cold −30℃ 96h Dry heat 80℃ 96h Damp heat 60℃, 90 to 95％RH 96h Page 437 440 4 41 Variable Resistor Type Multi Control Devices Cautions

  • Variable Resistor Type
  • Switch Type 437 443 Multi Control Devices Switch Type Variable Resistor Type NEW List of Varieties Multi Control Devices NEW

[Fig.2] 〔Circuit Used for Analog Stick Controller〕 We recommend you use the variable resistor in a voltage divider type as shown in Fig. A. 〔Impedance on the Output Side〕 Since this pot is designed to use with its output is connected directly to A/D port. lmpedance is considered to be mega ohm level. Then contact resistance in the pot is higher. Please refer to Flg-1. So when you use it in the circuit like Flg-2.Please make sure that impedance should be over than 1M-ohm. 〔Dew Condensation〕 Avoid using the product when condensation or drops of water might occur inside the product. Otherwise, insulation deterioration or shorting may occur. 〔Soldering〕 Do not employ wiring designs and soldering methods as illustrated in the schematic drawing. Molten solder flowing over the upper surface of PC board can cause imperfect contacts. Solder all metal inserted fixing including terminals & metal lugs into a substrate. 〔Stress Being Applied to the Terminals〕 Always be careful not to apply excessive stress on the terminals. Design appropriate soldering conditions. 〔Handling of Variable Resistors Equipped with Switches〕 Exercise care when packing or storing. Packaging or storing while load is applied to the shaft may cause a malfunction in performance. 〔Storage〕 ① Store the products as delivered, at a normal temperature and humidity, without direct sunshine and corrosive gas ambient. Use them at an earliest possible timing, not later than six months upon receipt. ② After breaking the seal, keep the products in a plastic bag to shut out ambient air, store them in the same environment as above, and use them up as soon as possible. ③ Do not stack too many switches. The above operation notes are quoted from the “Precaution and Guideline of Potentiometer for Electrical Devices”, a technical report issued by the Japan Electronics and Information Technology Industries Association EIAJ RCR-2191A （in March 2002） . For details, refer to the original technical report. Variable Resistor Type / Soldering Conditions Soldering surface temperature Soldering temperatureHeating time Soldering time No. of solders RKJXV RKJXK, RKJXV RKJXK Series Series 350℃max. 3s max. 1 time 90 to 100℃ 260℃ 45s max. 5s 1 time 90 to 100℃ 260℃ 60s max. 5s 1 time Tip temperature Soldering time No. of solders Preheating Dip soldering Reference for Dip Soldering Reference for Manual Soldering Variable Resistor Type / Cautions V V Terminal Solder Solder PC board pp pp A / D A / D [Fig.1] Fig.A.Voltage divider type