KHP EDI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

MATCHED SILICON RECTIFIER ELEMENTS RATED CURRENT TO 3.0 AMPERES PRV 5,000 TO 50,000 VOLTS FAST RECOVERY (RHP SERIES) ALL APPLICABLE MIL-STD-750 TESTS HIGH THERMAL CONDUCTIVITY ENCAPSULATION Max. Reverse Recovery Time , Trr (Fig.4) 200 nanosec Max. DC Reverse Current @ PRV and 25 oC, IR 250 Amps Storage Temperature Range, TSTG A Ambient Operating Temperature Range,TA Max. DC Reverse Current @ PRV and 100 oC, IR 240 Amps25 A -55 to +150oC oC -55 to +150oC oC RHP SERIES FAST RECOVERY

ELECTRICAL CHARACTERISTICS

(at TA=25 C Unless Otherwise Specified) FRM Max.One-Half Cycle Surge Current, IFM (Surge )@ 60Hz 82 6.00 4.0 B FRM Max. DC Reverse Current @ PRV and 25 oC, IR 100 Max.One-Half Cycle Surge Current, IFM Amps Storage Temperature Range, TSTG A Ambient Operating Temperature Range,TA (at TA=25 C Unless Otherwise Specified) Max. DC Reverse Current @ PRV and 100 oC, IR 400 Amps40 A -55 to +150oC oC -55 to +150oC oC KHP SERIES STANDARD RECOVERY (Surge )@ 60Hz EDI Type No. Peak ReverseVoltage PRV (Volts) Avg. Fwd.Current IO at 25 oC (Am ps) Max. Fwd Voltage Drop at 25 o VF (Volts) Dim ens ion L Inches Fig .3 Dim ens ion W Inches Fig .3 Case Sty le Fig .3 STANDARD RECOVERY KHP5 5,000 3.00 8 4.00 1.0 A KHP6 6,000 9 4.75 1.0 A KHP7 7,000 10 5.50 1.0 A KHP8 8,000 11 6.00 1.0 A KHP9 9,000 14 6.50 1.0 A KHP10 10,000 15 7.00 1.0 A KHP15 15,000 21 4.00 2.0 B KHP20 20,000 28 6.00 2.0 B KHP25 25,000 36 8.00 2.0 B KHP30 30,000 42 4.00 3.0 B KHP35 35,000 49 6.00 3.0 B KHP40 40,000 63 8.00 3.0 B KHP50 50,000 70 6.00 4.0 B 200 NANOSECOND RECOVERY (FIG.4) RHP5 5,000 2.50 10 4.00 1.0 A RHP6 6,000 2.50 11 4.75 1.0 A RHP7 7,000 2.50 12 5.50 1.0 A RHP8 8,000 2.50 13 6.00 1.0 A RHP9 9,000 2.50 16 6.50 1.0 A RHP10 10,000 2.50 17 7.00 1.0 A RHP15 15,000 2.25 25 4.00 2.0 B RHP20 20,000 2.25 33 6.00 2.0 B RHP25 25,000 2.25 42 8.00 2.0 B RHP30 30,000 2.25 50 4.00 3.0 B RHP35 35,000 2.25 58 6.00 3.0 B RHP40 40,000 2.25 65 8.00 3.0 B RHP50 50,000 2.25 KILOVOLT HIGH CURRENT RECTIFIER ASSEMBLIES Forward Current Repetitive Peak,I Forward Current Repetitive Peak,I EDI reserves the right to change these specifications at any time without notice. 2.75 2.75 2.75 2.50 2.50 2.50 2.25 2.25 2.25 2.25 2.25 2.25

3 Amps

FIG.1 OUTPUT CURRENT vs AMBIENT TEMPERATURE FIG.2 NON-REPETITIVE SURGE CURRENT FIG.3 PACKAGE STYLE 21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 * FAX 914-965-5531 * 1-800-678-0828 ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951. AMBIENT TEMPERATURE ( O Prior to the manufacture of these assemblies, the individual silicon junction is measured for maximum recovery time in the test circuit shown. % RATED FWD CURRENT It is recommended that a proper heat sink be used on the terminals of this device between the body and the soldering point to prevent damage form excess heat. Ee-mail:sales@edidiodes.comWwebsite:http:// www.edidiodes.com* L R R1, 2 NON-INDUCTIVE RESISTORS PULSE GENERATOR - HEWLETT PACKARD 214A OR EQUIV. IKC REP.RATE, 10 SEC. PULSE WIDTH ADJUST PULSE AMPLITUDE FOR PEAK IR TEST CIRCUIT FIG.4 TYPICAL REVERSE RECOVERY WAVEFORM PULSE GENERATOR D.U.T. SCOPER2

1 OHM

50 OHM

NUMBER OF CYCLES(60 Hz) 150 200 300 80 100 IFSM. PEAK SURGE CURRENT (AMP) 1.0A 0.5A TRR ZERO REFERENCE 0.25A RHP KHP 18-32 THREAD X / DEEP4 (4) MTG. INSERTS W CASE STYLE B OUTLINE 8 MAX.L 16-32 THREAD X / DEEP4 (2) MTG. INSERTS W CASE STYLE A OUTLINE 18-32 THREAD X / DEEP4 (2) MTG. INSERTS 400 240