RFANT8010080A3T WALSIN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
Page 1 of 9 ASC_RFANT8010080A3T_V04 May.2013 RFANT Series – RoHS Compliance CERAMIC ANTENNA Halogens Free Product
2.4 GHz ISM Band Working Frequency
P/N: RFANT8010080A3T *Contents in this sheet are subject to change without prior notice.
Page 2 of 9 ASC_RFANT8010080A3T_V04 May.2013
FEATURES
- Low profile for thin type terminal 3. High Stability in Temperature / Humidity Change 4. High mechanical strength
APPLICATIONS
- Bluetooth 2. Wireless LAN 3. HormRF 4. ISM band 2.4GHz wireless applications CONSTRUCTION DIMENSIONS Figure Symbol Dimension (mm) L 8.00 ± 0.20 W 1.05 ± 0.20 T 0.80 ± 0.10 A 0.30 ± 0.20 PIN Connection
1 Identification Mark
2 Soldering terminal
3 Feeding
Page 3 of 9 ASC_RFANT8010080A3T_V04 May.2013
ELECTRICAL CHARACTERISTICS
RFANT8010080A3T Specification Working Frequency Range 2.4 GHz ～ 2.5GHz Gain 2 dBi (Typical) VSWR 2 max. Polarization Linear Azimuth Beamwidth Omni-directional Impedance 50 Ω Rated Power (max.) 3 Watts Maximum Input Power 5 Watts for 5 minutes Operation Temperature -40˚C ~ +85˚C Remark: The specification is defined based on the test board dimension as in below SOLDER LAND PATTERN DESIGN Figure (Vertical type)
Page 4 of 9 ASC_RFANT8010080A3T_V04 May.2013 Antenna on Test Board ( FR4 Thickness 0.8mm) Vertical type Antenna S11 on Test Board Vertical type -15.34 dB @ 2.40 GHz -17.55 dB @ 2.45 GHz -15.17 dB @ 2.50 GHz
Page 5 of 9 ASC_RFANT8010080A3T_V04 May.2013 RADIATION PATTERN (Vertical type) Radiation Pattern and Gain were dependent on measurement board design. The specification of RFANT8010080A3T antenna was measur ed based on the PCB size and installation position as shown in the below figure Test Board Vertical Horizontal Y - Z Plane Average Gain= 1.136 dBi -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain = 3.25 dBi Average Gain = 0.44 dBi -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain= -0.06 dBi Average Gain=-7.16 dBi X - Z Plane Average Gain= -1.750dBi X Cut -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain= -2.68 dBi Average Gain= -9.30dBi X Cut -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain= 3.12 dBi Average Gain= -2.59 dBi X - Y Plane Average Gain= -2.322 dBi X Cut -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain= -2.43 dBi Average Gain= -7.10dBi X Cut -40 -30 -20 -10 120 150 180 210 240 270 300 330 Peak Gain= 0.96 dBi Average Gain= -4.08 dBi x Y Z x Y x Y Z X Z X Z Y Z Y
Page 6 of 9 ASC_RFANT8010080A3T_V04 May.2013 RELIABILITY TEST Test item Test condition / Test method Specification Solderability JIS C 0050-4.6 JESD22-B102D *Solder bath temperature ：235 ± 5 °C *Immersion time ：2 ± 0.5 sec Solder ：Sn3Ag0.5Cu for lead-free At least 95% of a surface of each terminal electrode must be covered by fresh solder. Leaching (Resistance to dissolution of metallization) IEC 60068-2-58 *Solder bath temperature ：260 ± 5 °C *Leaching immersion time ：30 ± 0.5 sec Solder : SN63A Loss of metallization on the edges of each electrode shall not exceed 25%. Resistance to soldering heat JIS C 0050-5.4 *Preheating temperature ：120~150 ℃, 1 minute. *Solder temperature ：270 ±5°C *Immersion time ：10 ±1 sec Solder ：Sn3Ag0.5Cu for lead-free Measurement to be made after keeping at room temperature for 24 ±2 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Loss of metallization on the edges of each electrode shall not exceed 25%. Drop Test JIS C 0044 Customer’s specification. *Height ：75 cm *Test Surface ：Rigid surface of concrete or steel. *Times ：6 surfaces for each units ；2 times for each side. No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Vibration JIS C 0040 *Frequency ：10Hz~55Hz~10Hz(1min) *Total amplitude ：1.5mm *Test times ：6hrs.(Two hrs each in three mutually perpendicular directions) No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Adhesive Strength of Termination JIS C 0051- 7.4.3 *Pressurizing force ： *Test time ：10±1 sec No remarkable damage or removal of the termination.
Page 7 of 9 ASC_RFANT8010080A3T_V04 May.2013 Bending test JIS C 0051- 7.4.1 The middle part of substrate shall be pressurized by means of the pressurizing rod at a rate of about 1 mm/s per second until the deflection becomes 1mm/s and then pressure shall be maintained for 5 ±1 sec. Measurement to be made after keeping at room temperature for 24 ±2 hours No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Temperature cycle JIS C 0025 1. 30 ±3 minutes at -40 °C ±3°C, 2. 10~15 minutes at room temperature, 3. 30 ±3 minutes at +85 °C ±3°C, 4. 10~15 minutes at room temperature, Total 100 continuous cycles Measurement to be made after keeping at room temperature for 24 ±2 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. High temperature JIS C 0021 *Temperature ：85 °C ±2°C *Test duration ：1000+24/-0 hours Measurement to be made after keeping at room temperature for 24 ±2 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Humidity (steady conditions) JIS C 0022 *Humidity ：90% to 95% R.H. *Temperature ：40 ±2°C *Time ：1000+24/-0 hrs. Measurement to be made after keeping at room temperature for 24 ±2 hrs ※ 500hrs measuring the first data then 1000hrs data No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C. Low temperature JIS C 0020 *Temperature ：-40 °C ±2°C *Test duration ：1000+24/-0 hours Measurement to be made after keeping at room temperature for 24 ±2 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85° C.
Page 8 of 9 ASC_RFANT8010080A3T_V04 May.2013 SOLDERING CONDITION Typical examples of soldering processes that provide reliable joints without any damage are given in Fig 2 Fig 2. Infrared soldering profile ORDERING CODE RF ANT 801008 0 A 3 T Walsin HF: RF /Pb free device Product code ANT : Antenna Dimension code Per 2 digits of Length, Width, Thickness : e.g. : 801008 = Length 80, Width 10, Thickness 8 Unit of dimension 0 : 0.1 mm 1 : 1.0 mm Application A : 2.4GHz ISM Band Specification Design Code Packing T : Reeled Minimum Ordering Quantity: 2000 pcs per reel. PACKAGING Plastic Tape specifications (unit :mm) Index Ao Bo Φ D T W Index E F Po P1 P2
Page 9 of 9 ASC_RFANT8010080A3T_V04 May.2013 A B C Reel dimensions Typing Quantity: 2000 pieces per 7” reel CAUTION OF HANDLING Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects, which might directly cause damage to the third party’s life, body or property. (1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Medical equipment (5) Disaster prevention / crime prevention equipment (6) Traffic signal equipment (7) Transportation equipment (vehicles, trains, ships, etc.) (8) Applications of similar complexity and /or reliability requirements to the applications listed in the above. Storage condition (1) Products should be used in 6 months from the day of WALSIN outgoing inspection, which can be confirmed. (2) Storage environment condition. Products should be storage in the warehouse on the following conditions. Temperature : -10 to +40 °C Humidity : 30 to 70% relative humidity Don’t keep products in corrosive gases such as sulfur. Chlorine gas or acid or it may cause oxidization of electrode, resulting in poor solderability. Products should be storage on the palette for the prevention of the influence from humidity, dust and son on. Products should be storage in the warehouse without heat shock, vibration, direct sunlight and so on. Products should be storage under the airtight packaged condition. Index A B C Dimension (mm) Φ 178 Φ 60.0 Φ 13.0