RD5-2403RD20A3

RS5-0503R20AX RSG | Alldatasheet

Document overview

• PDF pages: 6

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (6) STAND Juni 2016 Rev 01 DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 8 Pin SIL/ 16Pin DIL Package
• Wide 2:1 Input Range
• 1000VDC Isolation
• Up to 3000VDC Isolation
• Continuous Short Circuit Protection
• Efficiency up to 80%
• Operating Temperature Range -40° ~ +85°C
• Non Conductive Black Plastic Case, OptionalMetal Case
• Remote on/off Control(Optional) OUTPUT SPECIFICATION Voltage accuracy: ±2% Maximum Output Current: See table Line regulation: ± 0.5% max. LOAD REGULATION: from 25% to 100% Loading: ±1% max. Cross Regulation (Dual Output): ± 5% Short Circuit Protection : Indefinite (Automatic Recovery ) Ripple noise (20Mhz bandwidth): 80mV pk-pk max. Temperature coefficient: ±0.02%°C Capacitor load: See table INPUT SPECIFICATIONS Voltage Range: See table Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Voltage Metal Case: 1000VDC I/O Isolation Capacitance: 60pF max. I/O Isolation Resistance: 1000M Ohm, min Switching Frequency: 100 - 650kHz Humidity: 95% rel H Reliability Calculated MTBF : > 1.61MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC EN 60950-1 Remote ON/OFF Controll: see note ENVIRONMENTAL SPECIFICATON Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) Nickel-coated Copper PIN Material SIP Case: Alloy42 Solder-coated PIN Material DIP Case: Brass Solder-coated Ø 0.5mm Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 4.5g, (6.0g Metal Case) Weight Case-DIP: 6.5g, (8g Metal-Case) Dimmension SIP: 0.86 x 0.36 x 0.44“ Dimmension DIP: 0.92 x 0.55 x 0.40“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/max. 5 V Models: 12VDC max. 12V Models: 24VDC max. 24V Models: 40VDC max. 48V Models: 80VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria B RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria B SURGE: IEC 61000-4-5 Perf.Criteria B CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (6) STAND Juni 2016 Rev 01 RS5 - XX XX XX XX Power (W) Input Type A X * X Code internal Isolation (kVDC) MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RS5-0503R20AX 4.5-9 15 492 3.3 125 500 67 3300 RS5-0505R20AX 4.5-9 15 571 5 100 400 70 3300 RS5-0509R20AX 4.5-9 30 555 9 56 222 72 470 RS5-0512R20AX 4.5-9 30 555 12 42 167 72 470 RS5-0515R20AX 4.5-9 30 547 15 33 133 73 470 RS5-0524R20AX 4.5-9 60 533 24 21 83 75 220 RS5-1203R20AX 9-18 15 205 3.3 125 500 67 3300 RS5-1205R20AX 9-18 15 216 5 100 400 77 3300 RS5-1209R20AX 9-18 15 213 9 56 222 78 470 RS5-1212R20AX 9-18 15 208 12 42 167 80 470 RS5-1215R20AX 9-18 15 213 15 33 133 78 470 RS5-1224R20AX 9-18 15 208 24 21 83 80 220 RS5-2403R20AX 18-36 8 98 3.3 125 500 70 3300 RS5-2405R20AX 18-36 8 108 5 100 400 77 3300 RS5-2409R20AX 18-36 8 104 9 56 222 80 470 RS5-2412R20AX 18-36 8 104 12 42 167 80 470 RS5-2415R20AX 18-36 8 104 15 33 133 80 470 RS5-2424R20AX 18-36 8 104 24 21 83 80 220 RS5-4803R20AX 36-72 6 48 3.3 125 500 71 3300 RS5-4805R20AX 36-72 6 56 5 100 400 74 3300 RS5-4809R20AX 36-72 6 53 9 56 222 78 470 RS5-4812R20AX 36-72 6 53 12 42 167 78 470 RS5-4815R20AX 36-72 6 53 15 33 133 78 470 RS5-4824R20AX 36-72 6 52 24 21 83 80 220 RD5-0503R20AX 4.5-9 15 492 3.3 125 500 67 3300 RD5-0505R20AX 4.5-9 15 571 5 100 400 70 3300 RD5-0509R20AX 4.5-9 30 555 9 56 222 72 470 RD5-0512R20AX 4.5-9 30 555 12 42 167 72 470 RD5-0515R20AX 4.5-9 30 547 15 33 133 73 470 RD5-0524R20AX 4.5-9 60 533 24 21 83 75 220 RD5-1203R20AX 9-18 15 205 3.3 125 500 67 3300 RD5-1205R20AX 9-18 15 216 5 100 400 77 3300 RD5-1209R20AX 9-18 15 213 9 56 222 78 470 RD5-1212R20AX 9-18 15 208 12 42 167 80 470 RD5-1215R20AX 9-18 15 213 15 33 133 78 470 RD5-1224R20AX 9-18 15 208 24 21 83 80 220 Suffix “3”means 3KVdc isolation Suffix “C”means with control pin Suffix “M”means with Metal Case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o rm c o v e r o r e - ma i l to : info@rsg -electronic.de DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (6) STAND Juni 2016 Rev 01 DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RD5-2403R20AX 18-36 8 98 3.3 125 500 70 3300 RD5-2405R20AX 18-36 8 108 5 100 400 77 3300 RD5-2409R20AX 18-36 8 104 9 56 222 80 470 RD5-2412R20AX 18-36 8 104 12 42 167 80 470 RD5-2415R20AX 18-36 8 104 15 33 133 80 470 RD5-2424R20AX 18-36 8 104 24 21 83 80 220 RD5-4803R20AX 36-72 6 48 3.3 125 500 71 3300 RD5-4805R20AX 36-72 6 56 5 100 400 74 3300 RD5-4809R20AX 36-72 6 53 9 56 222 78 470 RD5-4812R20AX 36-72 6 53 12 42 167 78 470 RD5-4815R20AX 36-72 6 53 15 33 133 78 470 RD5-4824R20AX 36-72 6 52 24 21 83 80 220 RS5-0503RD20AX 4.5-9 20 471 ±3.3 ±63 ±250 70 ±1000 RS5-0505RD20AX 4.5-9 20 571 ±5 ±50 ±200 70 ±1000 RS5-0509RD20AX 4.5-9 20 540 ±9 ±28 ±111 74 ±220 RS5-0512RD20AX 4.5-9 25 533 ±12 ±21 ±83 75 ±220 RS5-0515RD20AX 4.5-9 25 533 ±15 ±17 ±67 75 ±220 RS5-0524RD20AX 4.5-9 60 563 ±24 ±10 ±42 71 ±100 RS5-1203RD20AX 9-18 15 188 ±3.3 ±63 ±250 73 ±1000 RS5-1205RD20AX 9-18 15 222 ±5 ±50 ±200 75 ±1000 RS5-1209RD20AX 9-18 15 210 ±9 ±28 ±111 79 ±220 RS5-1212RD20AX 9-18 15 208 ±12 ±21 ±83 80 ±220 RS5-1215RD20AX 9-18 15 210 ±15 ±17 ±67 79 ±220 RS5-1224RD20AX 9-18 30 219 ±24 ±10 ±42 76 ±100 RS5-2403RD20AX 18-36 8 94 ±3.3 ±63 ±250 73 ±1000 RS5-2405RD20AX 18-36 8 106 ±5 ±50 ±200 78 ±1000 RS5-2409RD20AX 18-36 8 105 ±9 ±28 ±111 79 ±220 RS5-2412RD20AX 18-36 8 104 ±12 ±21 ±83 80 ±220 RS5-2415RD20AX 18-36 8 104 ±15 ±17 ±67 80 ±220 RS5-2424RD20AX 18-36 20 106 ±24 ±10 ±42 78 ±100 RS5-4803RD20AX 36-72 6 47 ±3.3 ±63 ±250 73 ±1000 RS5-4805RD20AX 36-72 6 56 ±5 ±50 ±200 74 ±1000 RS5-4809RD20AX 36-72 6 53 ±9 ±28 ±111 79 ±220 RS5-4812RD20AX 36-72 6 53 ±12 ±21 ±83 79 ±220 RS5-4815RD20AX 36-72 6 52 ±15 ±17 ±67 80 ±220 RS5-4824RD20AX 36-72 12 55 ±24 ±10 ±42 75 ±100 RD5-0503RD20AX 4.5-9 20 471 ±3.3 ±63 ±250 70 ±1000 RD5-0505RD20AX 4.5-9 20 571 ±5 ±50 ±200 70 ±1000 RD5-0509RD20AX 4.5-9 20 540 ±9 ±28 ±111 74 ±220 RD5-0512RD20AX 4.5-9 25 533 ±12 ±21 ±83 75 ±220 RD5-0515RD20AX 4.5-9 25 533 ±15 ±17 ±67 75 ±220 RD5-0524RD20AX 4.5-9 60 563 ±24 ±10 ±42 71 ±100 RD5-1203RD20AX 9-18 15 188 ±3.3 ±63 ±250 73 ±1000 RD5-1205RD20AX 9-18 15 222 ±5 ±50 ±200 75 ±1000 RD5-1209RD20AX 9-18 15 210 ±9 ±28 ±111 79 ±220 RD5-1212RD20AX 9-18 15 208 ±12 ±21 ±83 80 ±220 RD5-1215RD20AX 9-18 15 210 ±15 ±17 ±67 79 ±220 RD5-1224RD20AX 9-18 30 219 ±24 ±10 ±42 76 ±100 RD5-2403RD20AX 18-36 8 94 ±3.3 ±63 ±250 73 ±1000 RD5-2405RD20AX 18-36 8 106 ±5 ±50 ±200 78 ±1000

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (6) STAND Juni 2016 Rev 01 MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RD5-2409RD20AX 18-36 8 105 ±9 ±28 ±111 79 ±220 RD5-2412RD20AX 18-36 8 104 ±12 ±21 ±83 80 ±220 RD5-2415RD20AX 18-36 8 104 ±15 ±17 ±67 80 ±220 RD5-2424RD20AX 18-36 20 106 ±24 ±10 ±42 78 ±100 RD5-4803RD20AX 36-72 6 47 ±3.3 ±63 ±250 73 ±1000 RD5-4805RD20AX 36-72 6 56 ±5 ±50 ±200 74 ±1000 RD5-4809RD20AX 36-72 6 53 ±9 ±28 ±111 79 ±220 RD5-4812RD20AX 36-72 6 53 ±12 ±21 ±83 79 ±220 RD5-4815RD20AX 36-72 6 52 ±15 ±17 ±67 80 ±220 RD5-4824RD20AX 36-72 12 55 ±24 ±10 ±42 75 ±100 Suffix “3”means 3KVdc isolation Suffix “C”means with control pin Suffix “M”means with Metal Case

05 Models

24 Models

12 Models

The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de 1. Maximum value at nominal input voltage and full load. 2. Typical value at nominal input voltage and full load. 3. 25% minimum loading is needed. 4. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 5. Ripple/Noise measured with 20MHz bandwidth. 6. Test by nominal input voltage and constant resistor load. 7. Measured Input reflected ripple current with a simulated source inductance of 12uH. 8. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 9. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 10. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. EFFICIENCYVS OUTPUTCURRENT

80 Lo Line

70 Nominal

0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT

70 Lo Line

60 Nominal

50 Hi Line

0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal 0% 20% 40% 60% Load 80% 100% 120% Efficiency(%) Efficiency(%) Efficiency(%) MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RD5-2409RD20AX 18-36 8 105 ±9 ±28 ±111 79 ±220 RD5-2412RD20AX 18-36 8 104 ±12 ±21 ±83 80 ±220 RD5-2415RD20AX 18-36 8 104 ±15 ±17 ±67 80 ±220 RD5-2424RD20AX 18-36 20 106 ±24 ±10 ±42 78 ±100 RD5-4803RD20AX 36-72 6 47 ±3.3 ±63 ±250 73 ±1000 RD5-4805RD20AX 36-72 6 56 ±5 ±50 ±200 74 ±1000 RD5-4809RD20AX 36-72 6 53 ±9 ±28 ±111 79 ±220 RD5-4812RD20AX 36-72 6 53 ±12 ±21 ±83 79 ±220 RD5-4815RD20AX 36-72 6 52 ±15 ±17 ±67 80 ±220 RD5-4824RD20AX 36-72 12 55 ±24 ±10 ±42 75 ±100 Suffix “3”means 3KVdc isolation Suffix “C”means with control pin Suffix “M”means with Metal Case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de 1. Maximum value at nominal input voltage and full load. 2. Typical value at nominal input voltage and full load. 3. 25% minimum loading is needed. 4. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 5. Ripple/Noise measured with 20MHz bandwidth. 6. Test by nominal input voltage and constant resistor load. 7. Measured Input reflected ripple current with a simulated source inductance of 12uH. 8. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 9. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 10. It’snecessary to add minimum capacitor in output for some models, please check single model datasheet for detail value. EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT 0% 20% 40% 60% Load 80% 100% 120% EFFICIENCYVS OUTPUTCURRENT Lo Line Nominal 0% 20% 40% 60% Load 80% 100% 120% Efficiency(%) Efficiency(%) Efficiency(%) DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 5 (6) STAND Juni 2016 Rev 01 The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +Vout +Vin L DC/DC Converter Load -Vin -Vout VB-1W&2W -Series C1 L 100uF/100V 12uH MCU CONVERTER 11. MCU (Master Control Unit) The MCU Pin Voltage is referenced to -Vin(Pin 1) ON:0 ~ 0.8VDC Max. (Short circuit Pin 1 and Pin 3) or open circuit OFF:4.5 to 15VDC Max.(or 3.5mA to 15mA Max.)(via R1、D1) OFF idle current:5mA typ. Connection example 1K 1N4148 R1 D1 PIN 3 12. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & test configuration. 13. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L RS5/RD5 -2W 100uF/100V 12uH The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +Vout +Vin L DC/DC Converter Load -Vin -Vout VB-1W&2W -Series C1 L 100uF/100V 12uH MCU CONVERTER 11. MCU (Master Control Unit) The MCU Pin Voltage is referenced to -Vin(Pin 1) ON:0 ~ 0.8VDC Max. (Short circuit Pin 1 and Pin 3) or open circuit OFF:4.5 to 15VDC Max.(or 3.5mA to 15mA Max.)(via R1、D1) OFF idle current:5mA typ. Connection example 1K 1N4148 R1 D1 PIN 3 12. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & test configuration. 13. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L RS5/RD5 -2W 100uF/100V 12uH The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +Vout +Vin L DC/DC Converter Load -Vin -Vout VB-1W&2W -Series C1 L 100uF/100V 12uH MCU CONVERTER 11. MCU (Master Control Unit) The MCU Pin Voltage is referenced to -Vin(Pin 1) ON:0 ~ 0.8VDC Max. (Short circuit Pin 1 and Pin 3) or open circuit OFF:4.5 to 15VDC Max.(or 3.5mA to 15mA Max.)(via R1、D1) OFF idle current:5mA typ. Connection example 1K 1N4148 R1 D1 PIN 3 12. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & test configuration. 13. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L RS5/RD5 -2W 100uF/100V 12uH DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - ma i l to : info@rsg- electronic.de Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. +Vout +Vin L DC/DC Converter Load -Vin -Vout VB-1W&2W -Series C1 L 100uF/100V 12uH MCU CONVERTER 11. MCU (Master Control Unit) The MCU Pin Voltage is referenced to -Vin(Pin 1) ON:0 ~ 0.8VDC Max. (Short circuit Pin 1 and Pin 3) or open circuit OFF:4.5 to 15VDC Max.(or 3.5mA to 15mA Max.)(via R1、D1) OFF idle current:5mA typ. Connection example 1K 1N4148 R1 D1 PIN 3 12. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & test configuration. 13. An external filter capacitor is required if the module has to meet IEC61000- 4-4 and IEC61000- 4-5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. C1 L RS5/RD5 -2W 100uF/100V 12uH

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 6 (6) STAND Juni 2016 Rev 01 RS5-XXXXR20A1 RS5-XXXXR20A1M RD5-XXXXR20A1 RD5-XXXXR20A1M DC/DC-Converter RS5/RD5-R20/RD20 2.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28