RD5-1203R30A1

RS5-0503R30A1 RSG | Alldatasheet

Document overview

• PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS5-R30/RD30 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics!

• 8 Pin SIL Package
• Wide 2:1 Input Range
• 1600VDC Isolation
• Continuous Short Circuit Protection
• Efficiency up to 84%
• Operating Temperature Range -40° ~ +85°C
• Plastic Case Standard , Metal Case (optional)
• Remote on/off control (optional) OUTPUT SPECIFICATION Voltage accuracy: ±1% Maximum Output Current: See table Line regulation: ± 0.5% max. LOAD REGULATION: From 25% to 100% Loading ±1% max Cross Regulation (Dual Output): ± 5% Short Circuit Protection : Indefinite (Automatic Recovery ) Ripple noise (20Mhz bandwidth): 75mV pk-pk max. Temperature coefficient: ±0.02% °C Capacitor load: See table Transient Recovery Time: 300us, typ. Transient Response: ( Deviation) ±3% max. INPUT SPECIFICATIONS Voltage Range: See table Start up Time: 20ms, typ. Max. Input Current: See table No-Load/Full-Load Input Current: See table Input Filter: Capacitors Input Reflected Ripple Current : 35mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1600VDC I/O Isolation Capacitance: 680pF max. I/O Isolation Resistance: 1000M Ohm, min Switching Frequency: 100 - 650kHz Humidity: 95% rel H Reliability Calculated MTBF : > 1.34MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC EN 60950-1 Remote on Controll: on: open or high impedance Remote off Controll: off: 3-6mA input current (via 1K) Off stand by current (Nominal Vin): 3mA max. ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: PIN Material: Non conductive black plastic PIN Material SIP Case: C519R-H Solder -coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 4.8g, typ. Dimmension SIP: 0.86 x 0.36 x 0.44“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ max. 5 V Models: 15VDC max. 12V Models: 36VDC max. 24V Models: 50VDC max. 48V Models: 100VDC max. Soldering Temperature: 260°C max. (2) EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class A (see EMI Filter note) ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 MODEL SELECTION GUIDE MODEL NUMBER INPUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Min. load (mA) Full load (mA) RS5-0503R30A1 4.5-9 65 640 3.3 175 700 74 2200 RS5-0505R30A1 4.5-9 70 800 5 150 600 76 2200 RS5-0512R30A1 4.5-9 75 750 12 62.5 250 82 470 RS5-0515R30A1 4.5-9 75 750 15 50 200 82 470 RS5-1203R30A1 9-18 25 260 3.3 175 700 76 2200 RS5-1205R30A1 9-18 15 320 5 150 600 81 2200 RS5-1212R30A1 9-18 35 305 12 62.5 250 84 470 RS5-1215R30A1 9-18 35 305 15 50 200 84 220 RS5-2403R30A1 18-36 15 133 3.3 175 700 74 2200 RS5-2405R30A1 18-36 15 160 5 150 600 79 2200 RS5-2412R30A1 18-36 20 156 12 62.5 250 82 470 RS5-2415R30A1 18-36 20 152 15 50 200 84 470 RS5-4803R30A1 36-72 10 66 3.3 175 700 75 2200 RS5-4805R30A1 36-72 10 82 5 150 600 78 2200 RS5-4812R30A1 36-72 15 78 12 62.5 250 81 470 RS5-4815R30A1 36-72 15 78 15 50 200 81 220 RS5-0505RD30A1 4.5-9 90 800 ±5 ±75 ±300 77 ±470 RS5-0512RD30A1 4.5-9 90 760 ±12 ±31.25 ±125 81 ±220 RS5-0515RD30A1 4.5-9 90 750 ±15 ±25 ±100 82 ±100 RS5-1205RD30A1 9-18 45 320 ±5 ±75 ±300 80 ±470 RS5-1212RD30A1 9-18 45 308 ±12 ±31.25 ±125 83 ±220 RS5-1215RD30A1 9-18 45 312 ±15 ±25 ±100 82 ±100 RS5-2405RD30A1 18-36 20 160 ±5 ±75 ±300 80 ±470 RS5-2412RD30A1 18-36 20 154 ±12 ±31.25 ±125 83 ±220 RS5-2415RD30A1 18-36 20 154 ±15 ±25 ±100 83 ±100 RS5-4805RD30A1 36-72 15 82 ±5 ±75 ±300 78 ±470 RS5-4812RD30A1 36-72 20 80 ±12 ±31.25 ±125 80 ±220 RS5-4815RD30A1 36-72 15 78 ±15 ±25 ±100 81 ±100 Suffix “C”means with control pin Suffix “M”means with Metal Case The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o rm c o v e r o r e - m a i l t o : info@rsg -electronic.de DC/DC-Converter RS5-R30/RD30 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! RS5 - XX XX XX 30 Power (W) Input Type A X * X Code internal Isolation (kVDC)

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. + V o u t + V inL D C /D C C o n ve rte r Lo a d C 1 -V in -V o u t C 1 L V B -0 5 X X X X X 2 2 0 u F /2 5 V 5 .6 u H V B -1 2 X X X X X S in g le 1 0 0 u F /1 0 0 V 18 u HD u a l 1 2 1 0 , 2 .2 u F /1 0 0 V V B -2 4 X X X X X 1 2 1 0 , 1 0 u F /3 5 V 18 u H V B -4 8 X X X X X 1 0 0 u F /1 0 0 V 56 u H The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg -electronic.d CONVERTER PIN 3 1. Operation at no load condition will not damage the produce ; however, it will not meet all specifications. 2. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 3. Measured with 20MHz bandwidth . 4. Test by minimal Vin and constant resistive load. 5. Test by normal Vin and 100%-25% load,25% Ioad step change . 6. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 7. The Remote on/off controll : ON: open or high impedance OFF: 3.0~6.0mA input current (via 1K) 8. Exceeding the absolute ratings of the unit could cause damage. It's not allowed for continuous operating ratings. 9. 25% minimum loading is needed. 10. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 11. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. +Vin 3~6 mA -Vin C1 L RS5-05xxR30/RD30A1 220uF/25V 5.6uH RS5-12xxR30A1 100uF/100V 18uH RS5-12xxRD30A1 1210, 2.2uF/100V 18uH RS5-24xxR30/RD30A1 1210, 10uF/35V 18uH RS5-48xxR30/RD30A1 100uF/100V 56uH DC/DC-Converter RS5-R30/RD30 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz. +Vout +Vout +VinLin Current Probe Cin DC/DC Converter Load DC/DC Converter Scope Load -Vin -Vout -Vout EMI Filter Input filter components (C1, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. + V o u t + V inL D C /D C C o n ve rte r Lo a d C 1 -V in -V o u t C 1 L V B -0 5 X X X X X 2 2 0 u F /2 5 V 5 .6 u H V B -1 2 X X X X X S in g le 1 0 0 u F /1 0 0 V 18 u HD u a l 1 2 1 0 , 2 .2 u F /1 0 0 V V B -2 4 X X X X X 1 2 1 0 , 1 0 u F /3 5 V 18 u H V B -4 8 X X X X X 1 0 0 u F /1 0 0 V 56 u H The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@rsg -electronic.d CONVERTER PIN 3 1. Operation at no load condition will not damage the produce ; however, it will not meet all specifications. 2. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 3. Measured with 20MHz bandwidth . 4. Test by minimal Vin and constant resistive load. 5. Test by normal Vin and 100%-25% load,25% Ioad step change . 6. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF,ESR<1.0© at 100KHz). 7. The Remote on/off controll : ON: open or high impedance OFF: 3.0~6.0mA input current (via 1K) 8. Exceeding the absolute ratings of the unit could cause damage. It's not allowed for continuous operating ratings. 9. 25% minimum loading is needed. 10. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI Filter of design & feature configuration. 11. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 220uF/100V. +Vin 3~6 mA -Vin C1 L RS5-05xxR30/RD30A1 220uF/25V 5.6uH RS5-12xxR30A1 100uF/100V 18uH RS5-12xxRD30A1 1210, 2.2uF/100V 18uH RS5-24xxR30/RD30A1 1210, 10uF/35V 18uH RS5-48xxR30/RD30A1 100uF/100V 56uH

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 RS5-XXXXR30A1 RS5-XXXXR30A1M RS5-XXXXR30A1 RS5-XXXXR30A1M RS5-XXXXR30A1 RS5-XXXXR30A1M DC/DC-Converter RS5-R30/RD30 3.0W Regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! MECHANICAL SPECIFICATIONS The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28