RS1-0503S15AX RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (4) STAND Juni 2016 Rev 01 DC/DC-Converter RS1/RD1-S15 1.5W unregulated Single Output we energize electronics! an acal group company we energize electronics!

  • 4 Pin SIL/ 8Pin DIL Package
  • 1000VDC Isolation
  • Up to 3000VDC Isolation
  • Low Ripple and Noise
  • Efficiency up to 88%
  • Operating Temperature Range -40° ~ +85°C
  • Non Conductive Black Plastic Case OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: ±1.2% (per 1%Vin Change) LOAD REGULATION: ±10% ( from 20 to 100%) Load Output 3.3V Model: ±20% Ripple noise (20Mhz bandwidth): 100mV pk-pk Temperature coefficient: ±0.02%°C Capacitor load: see table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: see table No-Load/Full-Load Input Current: see table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 80kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.121MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material SIP Case: Ø 0.5mm Alloy42 Solder-coated PIN Material DIP Case: Ø 0.5mm Brass Solder-coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 1.5g Weight Case-DIP: 1.8g Dimmension SIP: 0.46 x 0.24 x 0.40“ Dimmension DIP: 0.50 x 0.40 x 0.27“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/

5 V Models: 7VDC max

12V Models: 15VDC max 24V Models: 28VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (4) STAND Juni 2016 Rev 01 RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V DC/DC-Converter RS1/RD1-S15 1.5W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation MODEL SELECTION GUIDE MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIE NCY Capacitor Load(uF) No-Load (mA) FullLoad (mA) Fullload (mA) RS1-0503S15AX 5 30 370 3.3 400 81 220 RS1-0505S15AX 5 30 380 5 300 79 220 RS1-0507S15AX 5 35 366 7.2 208 82 220 RS1-0509S15AX 5 25 400 9 166 75 220 RS1-0512S15AX 5 25 385 12 125 78 220 RS1-0515S15AX 5 30 375 15 100 80 220 RS1-0518S15AX 5 30 353 18 83 85 220 RS1-0524S15AX 5 35 357 24 63 84 220 RS1-1203S15AX 12 15 167 3.3 400 75 220 RS1-1205S15AX 12 25 156 5 300 80 220 RS1-1207S15AX 12 25 167 7.2 208 75 220 RS1-1209S15AX 12 20 151 9 166 83 220 RS1-1212S15AX 12 15 152 12 125 82 220 RS1-1215S15AX 12 15 156 15 100 80 220 RS1-1218S15AX 12 15 156 18 83 80 220 RS1-1224S15AX 12 15 164 24 63 76 220 RS1-2403S15AX 24 15 83 3.3 400 75 220 RS1-2405S15AX 24 15 76 5 300 82 220 RS1-2407S15AX 24 10 78 7.2 208 80 220 RS1-2409S15AX 24 10 78 9 167 80 220 RS1-2412S15AX 24 15 74 12 125 84 220 RS1-2415S15AX 24 10 74 15 100 84 220 RS1-2418S15AX 24 10 78 18 83 80 220 RS1-2424S15AX 24 8 71 24 63 88 220 RS1-4803S15AX 48 10 42 3.3 400 75 220 RS1-4805S15AX 48 10 42 5 300 75 220 RS1-4807S15AX 48 8 41 7.2 208 76 220 RS1-4809S15AX 48 8 41 9 167 76 220 RS1-4812S15AX 48 6 41 12 125 77 220 RS1-4815S15AX 48 6 41 15 100 77 220 RS1-4818S15AX 48 6 41 18 83 77 220 RS1-4824S15AX 48 6 40 24 63 78 220 Isolation “3” means 3 KVdc isolation The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg- electronic.de

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Full load (mA) RD1-0505S15AX 5 35 390 3.3 400 77 220 RD1-0507S15AX 5 30 385 5 300 78 220 RD1-0509S15AX 5 30 400 7.2 208 75 220 RD1-0512S15AX 5 25 400 9 167 75 220 RD1-0515S15AX 5 25 370 12 125 81 220 RD1-0518S15AX 5 25 366 15 100 82 220 RD1-0524S15AX 5 25 375 18 83 80 220 RD1-1203S15AX 5 30 361 24 63 83 220 RD1-1205S15AX 12 15 170 3.3 400 74 220 RD1-1207S15AX 12 15 154 5 300 81 220 RD1-1209S15AX 12 25 164 7.2 208 76 220 RD1-1212S15AX 12 15 149 9 167 84 220 RD1-1215S15AX 12 15 156 12 125 80 220 RD1-1218S15AX 12 15 156 15 100 80 220 RD1-1224S15AX 12 15 156 18 83 80 220 RD1-0505S15AX 12 15 164 24 63 76 220 RD1-1524S15AX 24 10 83 3.3 400 75 220 RD1-2403S15AX 24 9 76 5 300 82 220 RD1-2405S15AX 24 10 75 7.2 208 83 220 RD1-2407S15AX 24 10 74 9 167 85 220 RD1-2409S15AX 24 10 78 12 125 80 220 RD1-2412S15AX 24 8 76 15 100 82 220 RD1-2415S15AX 24 8 78 18 83 80 220 RD1-2418S15AX 24 9 76 24 63 82 220 Isolation“3”means 3 KVdc isolation +Vout DC/DC Converter -Vout Scope The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg- electronic.de NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Full load (mA) RD1-0505S15AX 5 35 390 3.3 400 77 220 RD1-0507S15AX 5 30 385 5 300 78 220 RD1-0509S15AX 5 30 400 7.2 208 75 220 RD1-0512S15AX 5 25 400 9 167 75 220 RD1-0515S15AX 5 25 370 12 125 81 220 RD1-0518S15AX 5 25 366 15 100 82 220 RD1-0524S15AX 5 25 375 18 83 80 220 RD1-1203S15AX 5 30 361 24 63 83 220 RD1-1205S15AX 12 15 170 3.3 400 74 220 RD1-1207S15AX 12 15 154 5 300 81 220 RD1-1209S15AX 12 25 164 7.2 208 76 220 RD1-1212S15AX 12 15 149 9 167 84 220 RD1-1215S15AX 12 15 156 12 125 80 220 RD1-1218S15AX 12 15 156 15 100 80 220 RD1-1224S15AX 12 15 156 18 83 80 220 RD1-0505S15AX 12 15 164 24 63 76 220 RD1-1524S15AX 24 10 83 3.3 400 75 220 RD1-2403S15AX 24 9 76 5 300 82 220 RD1-2405S15AX 24 10 75 7.2 208 83 220 RD1-2407S15AX 24 10 74 9 167 85 220 RD1-2409S15AX 24 10 78 12 125 80 220 RD1-2412S15AX 24 8 76 15 100 82 220 RD1-2415S15AX 24 8 78 18 83 80 220 RD1-2418S15AX 24 9 76 24 63 82 220 Isolation“3”means 3 KVdc isolation +Vout DC/DC Converter -Vout Scope The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg- electronic.de NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. DC/DC-Converter RS1/RD1-S15 1.5W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation TEST CONFIGURATION N O T E +Vout +Vin DC/DC Converter -Vin -Vout TEST CONFIGURATIONS Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0Ù at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load MODEL NUMBER IN PUT Voltage Range (Vdc) INPUT Current OUTPUT Voltage (Vdc) OUTPUT Current EFFICIENCY @FL(%) Capacitor Load(uF) No-Load (mA) Full Load (mA) Full load (mA) RD1-0505S15AX 5 35 390 3.3 400 77 220 RD1-0507S15AX 5 30 385 5 300 78 220 RD1-0509S15AX 5 30 400 7.2 208 75 220 RD1-0512S15AX 5 25 400 9 167 75 220 RD1-0515S15AX 5 25 370 12 125 81 220 RD1-0518S15AX 5 25 366 15 100 82 220 RD1-0524S15AX 5 25 375 18 83 80 220 RD1-1203S15AX 5 30 361 24 63 83 220 RD1-1205S15AX 12 15 170 3.3 400 74 220 RD1-1207S15AX 12 15 154 5 300 81 220 RD1-1209S15AX 12 25 164 7.2 208 76 220 RD1-1212S15AX 12 15 149 9 167 84 220 RD1-1215S15AX 12 15 156 12 125 80 220 RD1-1218S15AX 12 15 156 15 100 80 220 RD1-1224S15AX 12 15 156 18 83 80 220 RD1-0505S15AX 12 15 164 24 63 76 220 RD1-1524S15AX 24 10 83 3.3 400 75 220 RD1-2403S15AX 24 9 76 5 300 82 220 RD1-2405S15AX 24 10 75 7.2 208 83 220 RD1-2407S15AX 24 10 74 9 167 85 220 RD1-2409S15AX 24 10 78 12 125 80 220 RD1-2412S15AX 24 8 76 15 100 82 220 RD1-2415S15AX 24 8 78 18 83 80 220 RD1-2418S15AX 24 9 76 24 63 82 220 Isolation“3”means 3 KVdc isolation +Vout DC/DC Converter -Vout Scope The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail to : info@rsg- electronic.de NOTE 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications.

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (4) STAND Juni 2016 Rev 01 PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output The Pin Connection of high isolation one is the same with normal one. 11.68 (0.46) 9.65 (0.38) 0.50 (0.02) 3.00 (0.12) 2.54 (0.10) 1.60 (0.06) 0.25 (0.01) 0.50 (0.02) 0.50 (0.02) 6.00* (0.24) Printed Face 1 3 42 DC-DC CONVERTER x x x x 6. 85 (0.27) 12.70 (0.50) 10.16 (0.40) 7.62 (0.30) 7.62 (0.30) 0.50 (0.02) 2.54 (0.10) 0.50 (0.02) Bottom View 3. 00 (0.12) DIA 0. 50 (0.02) 1 4 5 7 DC-DC CONVERTER x x x x Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 )

8 Pin DIL Package

  • The thickness of 48V input voltage model i s 7.50(0.29)

4 Pin SIL Package

Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) The Pin Connection of high isolation one is the same with normal one. RS1-XXXXS15A1 RD1-XXXXS15A1 PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output The Pin Connection of high isolation one is the same with normal one. 11.68 (0.46) 9.65 (0.38) 0.50 (0.02) 3.00 (0.12) 2.54 (0.10) 1.60 (0.06) 0.25 (0.01) 0.50 (0.02) 0.50 (0.02) 6.00* (0.24) Printed Face 1 3 42 DC-DC CONVERTER x x x x 6. 85 (0.27) 12.70 (0.50) 10.16 (0.40) 7.62 (0.30) 7.62 (0.30) 0.50 (0.02) 2.54 (0.10) 0.50 (0.02) Bottom View 3. 00 (0.12) DIA 0. 50 (0.02) 1 4 5 7 DC-DC CONVERTER x x x x Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 )

  • The thickness of 48V input voltage model i s 7.50(0.29)

Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) The Pin Connection of high isolation one is the same with normal one. RS1-XXXXS15A1 RD1-XXXXS15A1 PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output PIN CONNECTIONS PIN NUMBER SINGLE V Input +V Input +V Output V Output The Pin Connection of high isolation one is the same with normal one. 11.68 (0.46) 9.65 (0.38) 0.50 (0.02) 3.00 (0.12) 2.54 (0.10) 1.60 (0.06) 0.25 (0.01) 0.50 (0.02) 0.50 (0.02) 6.00* (0.24) Printed Face 1 3 42 DC-DC CONVERTER x x x x 6. 85 (0.27) 12.70 (0.50) 10.16 (0.40) 7.62 (0.30) 7.62 (0.30) 0.50 (0.02) 2.54 (0.10) 0.50 (0.02) Bottom View 3. 00 (0.12) DIA 0. 50 (0.02) 1 4 5 7 DC-DC CONVERTER x x x x Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 )

  • The thickness of 48V input voltage model i s 7.50(0.29)

Notes : All dimensions are typical in millimeters ( inches ). 2. Pin pitch and length tolerance: ±0.35 ( ±0.014 ) 3. Case Tolerance: ±0.5 ( ±0.02 ) The Pin Connection of high isolation one is the same with normal one. RS1-XXXXS15A1 RD1-XXXXS15A1 DC/DC-Converter RS1/RD1-S15 1.5W unregulated Single Output we energize electronics! an acal group company we energize electronics!

8 PIN DIL 4 PIN SIL

The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28