RD1-0505S02AX

RS1-0303S02AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (5) STAND Juni 2016 Rev 01 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. DC/DC-Converter RS1/RD1-S02 0.25W unregulated Single Output we energize electronics! an acal group company we energize electronics!

• 4 Pin SIL/ 8Pin DIL Package
• 1000VDC Isolation
• Up to 3000VDC Isolation
• Low Ripple and Noise
• Efficiency up to 77%
• Operating Temperature Range: -40° ~ +85°C
• Non Conductive Black Plastic Case
• EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: ±1.2% (per 1%Vin Change) LOAD REGULATION: ±10% ( from 20 to 100%) Load Output 3.3V Model: ±20% Ripple noise (20Mhz bandwidth): 100mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: see table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: see table No-Load/Full-Load Input Current: see table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC (Input/Output) I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 80kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.121MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material SIP Case: Ø 0.5mm Alloy42 Solder-coated PIN Material DIP Case: Ø 0.5mm Brass Solder-coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 1.5g Weight Case-DIP: 1.8g Dimmension SIP: 0.46 x 0.24 x 0.40“ Dimmension DIP: 0.50 x 0.40 x 0.27“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 3.3V Models: 5VDC max

5 V Models: 7VDC max

12V Models: 15VDC max 15V Models: 18VDC max 24V Models: 28VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class B ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A RoHS

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (5) STAND Juni 2016 Rev 01 RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC)48=48V 20=2.0 48=48V MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current Voltage Range (Vdc) No-Load (mA) Full Load (mA) Voltage (Vdc) Full load (mA) EFFICIENCY @FL(%) Capacitor Load(uF) RS1-0303S02AX 3.3 30 120 3.3 75.7 63 100 RS1-0305S02AX 3.3 25 115 5 50 66 100 RS1-0307S02AX 3.3 25 118 7.2 34.7 64 100 RS1-0309S02AX 3.3 25 118 9 27.7 64 100 RS1-0312S02AX 3.3 32 113 12 20.8 67 100 RS1-0315S02AX 3.3 25 118 15 16.6 64 100 RS1-0318S02AX 3.3 25 115 18 13.8 66 100 RS1-0324S02AX 3.3 20 115 24 10.4 66 100 RS1-0503S02AX 5 20 78 3.3 75.7 64 100 RS1-0505S02AX 5 17 70 5 50 71 100 RS1-0507S02AX 5 18 74 7.2 34.7 68 100 RS1-0509S02AX 5 15 68 9 27.7 73 100 RS1-0512S02AX 5 14 66 12 20.8 76 100 RS1-0515S02AX 5 20 70 15 16.6 71 100 RS1-0518S02AX 5 17 69 18 13.8 72 100 RS1-0524S02AX 5 18 65 24 10.4 77 100 RS1-1203S02AX 12 10 32 3.3 75.7 65 100 RS1-1205S02AX 12 12 31 5 50 67 100 RS1-1207S02AX 12 10 31 7.2 34.7 67 100 RS1-1209S02AX 12 12 33 9 27.7 64 100 RS1-1212S02AX 12 15 33 12 20.8 63 100 RS1-1215S02AX 12 13 31 15 16.6 67 100 RS1-1218S02AX 12 13 32 18 13.8 65 100 RS1-1224S02AX 12 18 38 24 10.4 55 100 RS1-1503S02AX 15 12 26 3.3 75.7 63 100 RS1-1505S02AX 15 8 27 5 50 62 100 RS1-1507S02AX 15 12 28 7.2 34.7 60 100 RS1-1509S02AX 15 12 28 9 27.7 60 100 RS1-1512S02AX 15 12 27 12 20.8 62 100 RS1-1515S02AX 15 10 27 15 16.6 61 100 RS1-1518S02AX 15 12 29 18 13.8 57 100 RS1-1524S02AX 15 12 29 24 10.4 57 100 RS1-2403S02AX 24 8 17 3.3 75.7 60 100 RS1-2405S02AX 24 7 17 5 50 61 100 RS1-2407S02AX 24 8 18 7.2 34.7 57 100 RS1-2409S02AX 24 8 17 9 27.7 62 100 RS1-2412S02AX 24 10 19 12 20.8 56 100 RS1-2415S02AX 24 7 19 15 16.6 55 100 RS1-2418S02AX 24 10 18 18 13.8 57 100 RS1-2424S02AX 24 10 18 24 10.4 59 100 RS1-4803S02AX 48 8 9 3.3 75.7 55 100 RS1-485S02AX 48 8 10 5 50 53 100 RS1-4807S02AX 48 8 10 7.2 34.7 54 100 RS1-4809S02AX 48 8 10 9 27.7 54 100 RS1-4812S02AX 48 8 9 12 20.8 55 100 RS1-4815S02AX 48 8 10 15 16.6 54 100 RS1-4818S02AX 48 8 11 18 13.8 49 100 RS1-4824S02AX 48 10 11 24 10.4 49 100 Suffix “3”means 3 KVdc isolation DC/DC-Converter RS1/RD1-S02 0.25W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (5) STAND Juni 2016 Rev 01 MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current Voltage Range (Vdc) No-Load (mA) Full Load (mA) Voltage (Vdc) Full load (mA) EFFICIENCY @FL(%) Capacitor Load(uF) RD1-0303S02AX 3.3 25 124 3.3 75.7 61 100 RD1-0305S02AX 3.3 25 118 5 50 64 100 RD1-0307S02AX 3.3 25 118 7.2 34.7 64 100 RD1-0309S02AX 3.3 25 118 9 27.7 64 100 RD1-0312S02AX 3.3 25 120 12 20.8 63 100 RD1-0315S02AX 3.3 25 118 15 16.6 64 100 RD1-0318S02AX 3.3 25 115 18 13.8 66 100 RD1-0324S02AX 3.3 20 115 24 10.4 66 100 RD1-0503S02AX 5 20 83 3.3 75.7 60 100 RD1-0505S02AX 5 15 72 5 50 69 100 RD1-0507S02AX 5 18 71 7.2 34.7 70 100 RD1-0509S02AX 5 18 71 9 27.7 70 100 RD1-0512S02AX 5 20 74 12 20.8 68 100 RD1-0515S02AX 5 20 74 15 16.6 68 100 RD1-0518S02AX 5 17 68 18 13.8 73 100 RD1-0524S02AX 5 23 72 24 10.4 69 100 RD1-1203S02AX 12 12 31 3.3 75.7 67 100 RD1-1205S02AX 12 10 32 5 50 65 100 RD1-1207S02AX 12 15 32 7.2 34.7 65 100 RD1-1209S02AX 12 12 35 9 27.7 60 100 RD1-1212S02AX 12 13 31 12 20.8 68 100 RD1-1215S02AX 12 16 37 15 16.6 57 100 RD1-1218S02AX 12 16 38 18 13.8 55 100 RD1-1224S02AX 12 18 41 24 10.4 51 100 RD1-1503S02AX 15 12 26 3.3 75.7 63 100 RD1-1505S02AX 15 10 26 5 50 63 100 RD1-1507S02AX 15 12 28 7.2 34.7 60 100 RD1-1509S02AX 15 12 28 9 27.7 60 100 RD1-1512S02AX 15 12 28 12 20.8 60 100 RD1-1515S02AX 15 13 28 15 16.6 59 100 RD1-1518S02AX 15 12 29 18 13.8 57 100 RD1-1524S02AX 15 12 29 24 10.4 57 100 RD1-2403S02AX 24 8 18 3.3 75.7 58 100 RD1-2405S02AX 24 7 17 5 50 60 100 RD1-2407S02AX 24 8 18 7.2 34.7 59 100 RD1-2409S02AX 24 8 18 9 27.7 58 100 RD1-2412S02AX 24 10 19 12 20.8 55 100 RD1-2415S02AX 24 7 18 15 16.6 59 100 RD1-2418S02AX 24 10 20 18 13.8 53 100 RD1-2424S02AX 24 10 19 24 10.4 55 100 Suffix “3”means 3 KVdc isolation DC/DC-Converter RS1/RD1-S02 0.25W unregulated Single Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (5) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS02AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS02AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic. de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS02AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS02AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic. de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS02AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS02AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS02AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic. de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5.Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. DC/DC-Converter RS1/RD1-S02 0.25W unregulated Single Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 5 (5) STAND Juni 2016 Rev 01 RS1-XXXXS02A1 RD1-xxxxS02A1 DC/DC-Converter RS1/RD1-S02 0.25W unregulated Single Output we energize electronics! an acal group company we energize electronics! RS1-XXXXS02A1 RD1-xxxxS02A1 RS1-XXXXS02A1 RD1-xxxxS02A1

8 PIN DIL 4 PIN SIL

The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28