RD1-0312S05AX

RS1-0303S05AX RSG | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 1 (5) STAND Juni 2016 Rev 01 DC/DC-Converter RS1/RD1-S05 0.5W unregulated Single Output we energize electronics! an acal group company we energize electronics!

• 4 Pin SIL/ 8Pin DIL Package
• 1000VDC Isolation
• Up to 3000VDC Isolation
• Low Ripple and Noise
• Efficiency up to 83%
• Operating Temperature Range: -40° ~ +85°C
• Non Conductive Black Plastic Case
• EMI Complies with EN55022 Class B OUTPUT SPECIFICATION Voltage accuracy: ±3% Line regulation: ±1.2% (per 1%Vin Change) LOAD REGULATION: ±10% ( from 20 to 100%) Load Output 3.3V Model: ±20% Ripple noise (20Mhz bandwidth): 100mV pk-pk Temperature coefficient: ±0.02% °C Capacitor load: see table INPUT SPECIFICATIONS Voltage Range: ±10% Max. Input Current: see table No-Load/Full-Load Input Current: see table Input Filter: Capacitors Input Reflected Ripple Current : 20mA pk-pk GENERAL SPECIFICATIONS Efficiency: See table I/O Isolation Voltage (60sec): 1000 ~ 3000VDC I/O Isolation Capacitance: 60pF typ. I/O Isolation Resistance: 1000M Ohm Switching Frequency: Variable 80kHz Humidity: 95% rel H Reliability Calculated MTBF : >1.121MHrs (MIL-HDBK-217 f) Safety Standard: (designed to meet): IEC 60950-1 1) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. 2) (1.5mm from case 10sec Max.) 3) All specifications typical at TA= 25°C, nominal input voltage and full load unless otherwise specified. 4) The information and specification contained in this data sheet are believed to be correct at time of publication. However RSG accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. ENVIRONMENTAL SPECIFICATION Operating Temperature range: -40°C ~+85°C (see Derating Curve) Maximum Case Temperature: 100°C Storage Temperature : -40°C ~+125°C Cooling : Nature Convection PHYSICAL SPECIFICATIONS: Case Material: Non-conductive Black Plastic (UL94V-0 rated) PIN Material SIP Case: Ø 0.5mm Alloy42 Solder-coated PIN Material DIP Case: Ø 0.5mm Brass Solder-coated Potting Material: Epoxy (UL94V-0 rated) Weight Case- Sip: 1.5g Weight Case-DIP: 1.8g Dimmension SIP: 0.46 x 0.24 x 0.40“ Dimmension DIP: 0.50 x 0.40 x 0.27“ ABSOLUTE MAXIMUM RATINGS (1) Input Surge Voltage (100ms)/ 3.3V Models: 6VDC max

5 V Models: 7VDC max

12V Models: 15VDC max 15V Models: 18VDC max 24V Models: 28VDC max 48V Models: 54VDC max Soldering Temperature (2): 260°C max. EMC SPECIFICATIONS Radiated-/Conducted Emissions: EN55022 Class B ESD: IEC 61000-4-2 Perf.Criteria A RS: IEC 61000-4-3 Perf.Criteria A EFT: IEC 61000-4-4 Perf.Criteria A SURGE: IEC 61000-4-5 Perf.Criteria A CS: IEC 61000-4-6 Perf.Criteria A PFMF IEC 61000-4-8 Perf.Criteria A

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 2 (5) STAND Juni 2016 Rev 01 RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V RD1 - XX XX X XX Power (W) Input 03=3.3V Type A X Code internal Isolation (kVDC) 48=48V 20=2.0 48=48V MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current Voltage Range (Vdc) No-Load (mA) Full Load (mA) Voltage (Vdc) Full load (mA) EFFICIENCY @FL(%) Capacitor Load(uF) RS1-0303S05AX 3. 3 20 205 3.3 152 76 100 RS1-0305S05AX 3. 3 25 216 5 100 70 100 RS1-0307S05AX 3. 3 25 216 7.2 69 70 100 RS1-0309S05AX 3. 3 25 216 9 56 70 100 RS1-0312S05AX 3. 3 25 201 12 42 72 100 RS1-0315S05AX 3. 3 25 208 15 33 73 100 RS1-0318S05AX 3. 3 25 208 18 28 73 100 RS1-0324S05AX 3.3 25 208 24 21 73 100 RS1-0503S05AX 5 20 132 3.3 151.5 76 100 RS1-0505S05AX 5 13 121 5 100 83 100 RS1-0507S05AX 5 15 134 7.2 69.44 75 100 RS1-0509S05AX 5 15 128 9 55.55 78 100 RS1-0512S05AX 5 18 127 12 41.67 79 100 RS1-0515S05AX 5 22 130 15 33.33 77 100 RS1-0518S05AX 5 20 127 18 27.77 79 100 RS1-0524S05AX 5 25 134 24 20.83 75 100 RS1-1203S05AX 12 15 58 3.3 151.5 72 100 RS1-1205S05AX 12 10 54 5 100 78 100 RS1-1207S05AX 12 15 57 7.2 69.44 73 100 RS1-1209S05AX 12 15 57 9 55.56 73 100 RS1-1212S05AX 12 20 58 12 41.67 72 100 RS1-1215S05AX 12 20 61 15 33.33 69 100 RS1-1218S05AX 12 15 61 18 27.77 68 100 RS1-1224S05AX 12 15 59 24 20.83 71 100 RS1-1503S05AX 15 10 44 3.3 151.5 75 100 RS1-1505S05AX 15 8 43 5 100 78 100 RS1-1507S05AX 15 12 44 7.2 69.44 75 100 RS1-1509S05AX 15 12 44 9 55.55 75 100 RS1-1512S05AX 15 10 44 12 41.67 77 100 RS1-1515S05AX 15 15 48 15 33.33 70 100 RS1-1518S05AX 15 12 51 18 27.77 66 100 RS1-1524S05AX 15 10 51 24 20.83 66 100 RS1-2403S05AX 24 8 31 3.3 151.5 69 100 RS1-2405S05AX 24 8 29 5 100 73 100 RS1-2407S05AX 24 10 30 7.2 69.44 70 100 RS1-2409S05AX 24 10 30 9 55.55 71 100 RS1-2412S05AX 24 8 30 12 41.67 71 100 RS1-2415S05AX 24 10 29 15 33.33 73 100 RS1-2418S05AX 24 10 29 18 27.77 73 100 RS1-2424S05AX 24 10 29 24 20.83 72 100 RS1-4803S05AX 48 6 17 3.3 151.5 60 100 RS1-485S05AX 48 6 16 5 100 66 100 RS1-4807S05AX 48 6 17 7.2 69.44 60 100 RS1-4809S05AX 48 6 17 9 55.55 62 100 RS1-4812S05AX 48 6 17 12 41.67 64 100 RS1-4815S05AX 48 6 17 15 33.33 62 100 RS1-4818S05AX 48 6 17 18 27.77 62 100 RS1-4824S05AX 48 10 18 24 20.83 61 100 Suffix “3”means 3 KVdc isolation DC/DC-Converter RS1/RD1-S05 0.5W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (5) STAND Juni 2016 Rev 01 MODEL SELECTION GUIDE MODEL NUMBER INPUT INPUT Current OUTPUT OUTPUT Current Voltage Range (Vdc) No-Load (mA) Full Load (mA) Voltage (Vdc) Full load (mA) EFFICIENCY @FL(%) Capacitor Load(uF) RD1-0303S05AX 3.3 20 205 3.3 152 76 100 RD1-0305S05AX 3.3 25 216 5 100 70 100 RD1-0307S05AX 3.3 25 216 7.2 69 70 100 RD1-0309S05AX 3.3 25 216 9 56 70 100 RD1-0312S05AX 3.3 25 201 12 42 72 100 RD1-0315S05AX 3.3 25 208 15 33 73 100 RD1-0318S05AX 3.3 25 208 18 28 73 100 RD1-0324S05AX 3.3 25 208 24 21 73 100 RD1-0503S05AX 5 16 132 3.3 151.5 76 100 RD1-0505S05AX 5 15 124 5 100 81 100 RD1-0507S05AX 5 15 134 7.2 69.44 75 100 RD1-0509S05AX 5 15 128 9 55.55 78 100 RD1-0512S05AX 5 18 127 12 41.67 79 100 RD1-0515S05AX 5 22 130 15 33.33 77 100 RD1-0518S05AX 5 20 127 18 27.77 79 100 RD1-0524S05AX 5 25 134 24 20.83 75 100 RD1-1203S05AX 12 15 58 3.3 151.5 73 100 RD1-1205S05AX 12 12 54 5 100 78 100 RD1-1207S05AX 12 15 57 7.2 69.44 73 100 RD1-1209S05AX 12 15 58 9 55.56 73 100 RD1-1212S05AX 12 20 58 12 41.67 72 100 RD1-1215S05AX 12 20 61 15 33.33 69 100 RD1-1218S05AX 12 15 61 18 27.77 68 100 RD1-1224S05AX 12 15 59 24 20.83 71 100 RD1-1503S05AX 15 10 44 3.3 151.5 75 100 RD1-1505S05AX 15 8 43 5 100 78 100 RD1-1507S05AX 15 12 44 7.2 69.44 75 100 RD1-1509S05AX 15 12 44 9 55.55 75 100 RD1-1512S05AX 15 10 44 12 41.67 77 100 RD1-1515S05AX 15 15 48 15 33.33 70 100 RD1-1518S05AX 15 12 51 18 27.77 66 100 RD1-1524S05AX 15 10 51 24 20.83 66 100 RD1-2403S05AX 24 8 31 3.3 151.5 69 100 RD1-2405S05AX 24 10 29 5 100 74 100 RD1-2407S05AX 24 10 31 7.2 69.44 69 100 RD1-2409S05AX 24 10 30 9 55.55 71 100 RD1-2412S05AX 24 10 31 12 41.67 69 100 RD1-2415S05AX 24 9 31 15 33.33 69 100 RD1-2418S05AX 24 10 29 18 27.77 73 100 RD1-2424S05AX 24 10 29 24 20.83 72 100 Suffix “3”means 3 KVdc isolation DC/DC-Converter RS1/RD1-S05 0.5W unregulated Single Output we energize electronics! an acal group company we energize electronics! Suffix “3” means 3KVdc isolation

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 4 (5) STAND Juni 2016 Rev 01 +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS05AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS05AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS05AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS05AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. +Vout +Vin DC/DC Converter -Vin -Vout +Vout +Vin DC/DC Converter -Vin -Vout Input Reflected Ripple Current Test Step Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin(47uF, ESR<1.0© at 100KHz) at nominal input and full load. Lin Current Probe Cin Load Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 20MHz . Load EMI Filter Input filter components (C1 , L , C2 , C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. L Load C1 C2 +Vout DC/DC Converter -Vout Scope C1 L C2 C3 RS1/RD1-03XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-05XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-12XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-15XXS05AX 1210, 2.2uF/100V 18uH RS1/RD1-24XXS05AX 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS1/RD1-48XXS05AX Electrolytic capacitor, 10uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV The models listed above is just for standard type. If you need the special specification product, please contact our service member by telephone presented in shortform cover or e-mail t o : info@rsg -electronic.de 1.Ripple/Noise measured with 20MHz bandwidth. 2.Tested by minimal Vin and constant resistive load. 3.Measured Input reflected ripple current with a simulated source inductance of 12uH. 4.Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design & feature configuration. 7. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4- 5. The filter capacitor RSG suggest: Nippon - chemi - con KY series, 470uF/100V. DC/DC-Converter RS1/RD1-S05 0.5W unregulated Single Output we energize electronics! an acal group company we energize electronics!

RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 5 (5) STAND Juni 2016 Rev 01 RS1-XXXXS05A1 RD1-XXXXS05A1 RS1-XXXXS05A1 RD1-XXXXS05A1 RS1-XXXXS05A1 RD1-XXXXS05A1 DC/DC-Converter RS1/RD1-S05 0.5W unregulated Single Output we energize electronics! an acal group company we energize electronics!

8 PIN DIL 4 PIN SIL

The models listed here are just standard type. If you need a product with special specification or you have questions regarding packing standards (Tube oder Tape/Reel) as well as application support, please contact our specialists: sales@rsg-electronic.de or +49 69-984047-41/-28