RC5532 FAIRCHILD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • Small signal bandwidth – 10 MHz
  • Output drive capability – 600 Ω , 10 VRMS
  • Input noise voltage – 5 nV/
  • DC voltage gain – 50,000
  • AC voltage gain – 2200 at 10 KHz
  • Power bandwidth – 140 KHz
  • Slew rate – 8 V/µS
  • Large supply voltage range – ±3V to ±20V

Description

The RC5532 is a high performance, dual low noise opera- tional amplifier. Compared to standard dual operational amplifiers, such as the RC747, it shows better noise perfor- mance, improved output drive capability, and considerably higher small-signal and power bandwidths. This makes the device especially suitable for application in high quality and professional audio equipment, instrumenta- tion, control circuits, and telephone channel amplifiers. The op amp is internally compensated for gains equal to one. If very low noise is of prime importance, it is recommended that the RC5532A version be used which has guaranteed noise specifications. Hz RC5532/RC5532A High Performance Dual Low Noise Operational Amplifier Block Diagram A B 65-5532-01 Output A –Input A +Input A –VS +VS Output B –Input B +Input B

RC5532/RC5532A PRODUCT SPECIFICATION REV. 1.1.3 6/14/01 Pin Assignments Absolute Maximum Ratings (beyond which the device may be damaged)1 Notes: 1. Functional operation under any of these conditions is NOT implied. 2. For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage. 3. Short circuit to ground on one amplifier only. Operating Conditions Parameter Min. Typ. Max. Units Supply Voltage ±22 V Input Voltage ±V S V Differential Input Voltage 0.5 V P D T A < 50°C PDIP 468 mW Junction Temperature PDIP 125 °C Storage Temperature -65 150 °C Operating Temperature RC5532/A 0 70 °C Lead Soldering Temperature (10 sec) 300 °C Parameter Min. Typ. Max. Units θ JA Thermal resistance PDIP 160 °C/W For T A > 50°C Derate at PDIP 6.25 mW/°C Output (A) –Input (A) +Input (A) –VS +VS Output (B) –Input (B) +Input (B)

8 PIN PDIP

PRODUCT SPECIFICATION RC5532/RC5532A REV. 1.1.3 6/14/01 S = ±15V and T A = +25˚C unless otherwise noted) Notes: 1. Diodes protect the inputs against over-voltage. Therefore, unless current-limiting resistors are used, large currents will f low if the differential input voltage exceeds 0.6V. Maximum input current should be limited to ±10mA. 2. Over Temperature: RC = 0 °C T A 70°C

Electrical Characteristics

S = ±15V and T A = +25°C ) RC5532/5532A Parameters Test Conditions Min. Typ. Max. Units Input Offset Voltage 0.5 4.0 mV Over Temperature 5.0 mV Input Offset Current 10 150 nA Over Temperature 200 nA Input Bias Current 200 800 nA Over Temperature 1000 nA Supply Current 6.0 16 mA Over Temperature 22 mA Input Voltage Range ±12 ±13 V Common Mode Rejection Ratio 70 100 dB Power Supply Rejection Ratio 80 100 dB Large Signal Voltage Gain R L 2 K Ω , V OUT = ±10V 25 100 V/mV Over Temperature 15 50 R L 600 Ω , V OUT = ±10V 15 50 Over Temperature 10 Output Voltage Swing R L 600 Ω ±12 ±13 V R L = 600 Ω , V S = ±18V ±15 ±16 R L Ω Input Resistance (Diff. Mode) 300 K Ω Short Circuit Current 38 mA RC/RM5532A Parameters Test Conditions Min. Typ. Max. Units Input Noise Voltage Density F O = 30 Hz 8.0 12 nV/ Hz F O = 1 kHz 5.0 6.0 Input Noise Current Density F O = 30 Hz 2.7 pA/ Hz F O = 1 kHz 0.7 Channel Separation F = 1 kHz, R S = 5 k Ω 110 dB

Figure 1. Closed Loop Frequency Response Figure 2. Follower, Transient Response

10 MHz

PRODUCT SPECIFICATION RC5532/RC5532A REV. 1.1.3 6/14/01 7 Mechanical Dimensions (continued) 8-Lead Plastic DIP Package A — .210 — 5.33 Symbol Inches Min. Max. Min. Max. Millimeters Notes A1 .015 — .38 — .022 .56B .014 .36 B1 .045 .070 1.14 1.78 D .348 .430 8.84 10.92 .300 .325 7.62 8.26 .240 .280 6.10 7.11 E e — .430 — 10.92 .005 — .13 — A2 .115 .195 2.93 4.95 .100 BSC 2.54 BSC eB .115 .160 2.92 4.06L 8° 8° 5N C .008 .015 .20 .38 Notes: Dimensioning and tolerancing per ANSI Y14.5M-1982. "D" and "E1" do not include mold flashing. Mold flash or protrusions shall not exceed .010 inch (0.25mm). Terminal numbers are for reference only. "C" dimension does not include solder finish thickness. Symbol "N" is the maximum number of terminals. D e B A L 5 8 E eB C

RC5532/RC5532A PRODUCT SPECIFICATION 6/14/01 0.0m 003 Stock#DS30004841 © 2001 Fairchild Semiconductor Corporation LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

Ordering Information

Product Number Temperature Range Screening Package RC5532N/RC5532AN 0 °C to +70°C Commercial 8 Pin Plastic DIP