RBBLN16083G6W0T WALSIN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
Page 1 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016 RBBLN Series – 1608(0603)- RoHS Compliance MULTILAYER CERAMIC BALUN TRANSFORMER Halogens Free Product LTE Band RF Application P/N: RBBLN16083G6W0T *Contents in this sheet are subject to change without prior notice.
Page 2 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016
FEATURES
- Miniature footprint: 1.6 X 0.8X 0.6 mm3 2. Low insertion loss which can reduce power consumption 3. Low in-band amplitude and phase imbalance enhances system performance 4. LTCC process
APPLICATIONS
- 3550 ~ 3700 MHz working frequency CONSTRUCTION Top view DIMENSIONS Figure Symbol Dimension (mm) L 1.60 ± 0.15 W 0.80 ± 0.15 T 0.60 ± 0.10 A 0.175 ± 0.15 B 0.25 ± 0.15 C 0.25 ± 0.15 D 0.50 ± 0.15 E 0.20 ± 0.15 PIN Definition PIN Definition P1 Unbalance Port P4 Balance Port P2 DC or GND P5 GND P3 Balance Port P6 NC Top view Bottom view Side view P3 P2 P1 P4 P5 P6
Page 3 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016
ELECTRICAL CHARACTERISTICS
RBBLN16083G6W0T Specification Frequency Range 3550 ~ 3700 MHz Insertion Loss 1.2 dB max. Phase Difference 180° ± 10° Amplitude Difference 2.0 dB max. VSWR 2.0 max. Impedance( Unbalanced) 50 Ω Impedance( Balanced) 50 Ω Operating temperature Range -40℃~85℃ Moisture sensitivity levels MSL is LEVEL 1 (Refer to : IPC/JEDEC J-STD-020) Typical Electrical Chart SOLDER LAND PATTERN SOLDER LAND PATTERN Unit : mm Line width to be designed to match 50 Ω characteristic impedance, depending on PCB material and thickness.
Page 4 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016 RELIABILITY TEST Test item Test condition / Test method Specification Solderability JIS C 0050-4.6 JESD22-B102D *Solder bath temperature：235 5C *Immersion time：2 0.5 sec Solder：Sn3Ag0.5Cu for lead-free At least 95% of a surface of each terminal electrode must be covered by fresh solder. Leaching (Resistance to dissolution of metallization) IEC 60068-2-58 *Solder bath temperature：260 5C *Leaching immersion time：30 0.5 sec Solder : SN63A Loss of metallization on the edges of each electrode shall not exceed 25%. Resistance to soldering heat JIS C 0050-5.4 *Preheating temperature：120~150℃, 1 minute. *Solder temperature：2705C *Immersion time：101 sec Solder：Sn3Ag0.5Cu for lead-free Measurement to be made after keeping at room temperature for 242 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. Loss of metallization on the edges of each electrode shall not exceed 25%. Drop Test JIS C 0044 Customer’s specification. *Height：75 cm *Test Surface：Rigid surface of concrete or steel. *Times：6 surfaces for each units；2 times for each side. No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. Vibration JIS C 0040 *Frequency：10Hz~55Hz~10Hz(1min) *Total amplitude：1.5mm *Test times：6hrs.(Two hrs each in three mutually perpendicular directions) No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. Adhesive Strength of Termination JIS C 0051- 7.4.3 *Pressurizing force： *Test time：10±1 sec No remarkable damage or removal of the termination. Bending test JIS C 0051- 7.4.1 The middle part of substrate shall be pressurized by means of the pressurizing rod at a rate of about 1 mm/s per second until the deflection becomes 1mm/s and then pressure shall be maintained for 51 sec. Measurement to be made after keeping at room temperature for 242 hours No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C.
Page 5 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016 Temperature cycle JIS C 0025 1. 303 minutes at -40C3C, 2. 10~15 minutes at room temperature, 3. 303 minutes at +85C3C, 4. 10~15 minutes at room temperature, Total 100 continuous cycles Measurement to be made after keeping at room temperature for 242 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. High temperature JIS C 0021 *Test duration：1000+24/-0 hours Measurement to be made after keeping at room temperature for 242 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. Humidity (steady conditions) JIS C 0022 *Humidity：90% to 95% R.H. *Temperature：402C *Time：1000+24/-0 hrs. Measurement to be made after keeping at room temperature for 242 hrs ※ 500hrs measuring the first data then 1000hrs data No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C. Low temperature JIS C 0020 *Test duration：1000+24/-0 hours Measurement to be made after keeping at room temperature for 242 hrs No mechanical damage. Electrical specification shall satisfy the descriptions in electrical characteristics under the operational temperature range within -40 ~ 85°C.
Page 6 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016 SOLDERING CONDITION Typical examples of soldering processes that provide reliable joints without any damage are given in Fig 2, Fig 2. Infrared soldering profile ORDERING CODE RB BLN 1608 3G6 W 0 T Walsin RF device with DC block Product Code BLN : BALUN Dimension code Per 2 digits of Length, Width: e.g. : 1608 = Length 16, Width 08, Central Frequency 3G6:3.6GHz Application W:Wi-Max Specification Design Code Packing T : Reeled Minimum Ordering Quantity: 4000 pcs per reel. PACKAGING Paper Tape specifications (unit :mm) Index Ao Bo D T W Index E F Po P1 P2
Page 7 of 7 ASC_RBBLN16083G6W0T_V02 Nov. 2016 Reel dimensions A B C Taping Quantity: 4000 pieces per 7” reel CAUTION OF HANDLING Limitation of Applications Please contact us before using our products for the applications listed below which require especia lly high reliability for the prevention of defects, which might directly cause damage to the third party’s life, body or property. (1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Medical equipment (5) Disaster prevention / crime prevention equipment (6) Traffic signal equipment (7) Transportation equipment (vehicles, trains, ships, etc.) (8) Applications of similar complexity and /or reliability requirements to the applications listed in the above. Storage condition (1) Products should be used in 6 months from the da y of WALSIN outgoing inspection, which can be confirmed. (2) Storage environment condition. Products should be storage in the warehouse on the following conditions. Temperature : -10 to +40℃ Humidity : 30 to 70% relative humidity Don’t keep products in corrosi ve gases such as sulfur. Ch lorine gas or acid or it may cause oxidization of electrode, resulting in poor solderability. Products should be storage on the palette for the prevention of the influence from humidity, dust and son on. Products should be storage in the warehouse without heat shock, vibration, direct sunlight and so on. Products should be storage under the airtight packaged condition. Index A B C Dimension (mm) Φ178.0 Φ60.0 Φ13.0